Officezone IDEAL 4810 (18-3/4''), IDEAL 4810-11 (18-3/4''), IDEAL 5210 (20-1/2''), 4810, 4810-11 Operating Instructions Manual

1

Office Zone

1-800-543-5454

1-800-543-5454

[phone]

IDEAL CUTTERS

Model 4810 (18-3/4”)

Model 4810-11 (18-3/4”)

Model 5210 (20-1/2”)

2

Safety Rules

• Ensure that at no time more than one person is working at the machine.

• Leave the key for the safety lock with the person responsible for the cutting machine.

• Power operated cutting machines must be operated only by trained and reliable personnel. Part of

the training is to become familiar with the operating instructions.

• The operating instructions must be accessible at any time and must be strictly observed.

• Do not reach into cutting area while the knife is in operation.

• Change knife and cutting stick only with the main switch in “off” position. For other maintenance

and repair, which requires removal of machine covers, always disconnect the plug.

• Defects in or damage to cutting machines, which affect the safety, must be repaired immediately.

Until such faults have been eliminated, the cutting machine must be put out of operation.

• Annual routine inspection by specially trained service technicians are recommended for all safety

devices, particularly the electrical control measures in the cutting machine. Records should be
kept of these safety inspections.

• Transportation of knives is only allowing specially designed wooden ca ses supplied by your local

distributor. When inserting knife into the wooden case, ensure that the sharp edge lies flush with
that side of the case into which the holes for the securing screws have been drilled.

• IMPORTANT – The safety rules must be strictly observed. Please make sure that you are

familiar with the operation of the paper cutter.

Installation

The entire machine is dispatched in one package, but the stand (#7) and the hand wheel (#19) for
the paper clamp have been dismounted from the machine.

The tool box contains:

- a set of tools for service and maintenance,

- the mounting hardware for the stand,

- the back gauge crank (#3) with a mounting screw,

- two keys for the safety lock.

• Place machine (#1) on stand (#2).

• Insert securing bolts for the st and into provided holes and secure with nuts.

• Place paper tray (#8) into the stand (#7).

• Mount the hand wheel for the paper clamp (#19) and the crank for the back gauge (#3). Secure

these parts with provided screws.

• Connect power cord with plug to a normal single phase AC socket.

The machine is now ready to be operated.

3

Performance

All paper qualities and light cardboard can be cut using the full cutting height and cutting length of
the machine.

4810

Cutting Length 475 mm

Cutting Height 80 mm

Table depth 460 mm

Narrow cut 30 mm

Features and Operation

• Main Switch (#11)

Turn main switch (#11) to position “|” (on), in order to begin operation. The main switch can be
sued as an EMERGENCY SWITCH, which stops the machine immediately.

• Safety lock with key (#6)

The key can be removed to prevent unauthorized use. To activate the machine, turn key 45º to the
right.

• Re-set button (#12)

Before the knife can be activated on models IDEAL 4810 and IDEAL 5210, the re-set button has
to be pressed to re-establish the “ready to cut” status of the machine. The yellow pilot light in the
viewing window (#14) comes on and indicates, that the machine s is ready for use. The model
IDEAL 4810-11 does not have a re-set button.

• Two-hand operation

Only by pressing the right and the left push button switch (#5) simultaneously (within half a
second), can a cut be executed. Keep push buttons (#5) depressed until the knife has reached it
lowest position. As soon as the push buttons have been released, the knife returns automatically to
its home position.

• Automatic knife return

If a cut cycle is interrupted by releasing both push button switches (#5), the knife returns
automatically to its home position. IF only one of push buttons is released, the knife stops in the
reached position until the second push button is released as well.

• Spindle clamp system

The clamp holds the paper pile in position while cutting. The paper clamp (#15) is lowered and
raised by turning the hand wheel (#19).

(18-3/4”)

(3-1/8”)

(18-1/8”)

(1-3/16”)

5210

4810-11

520 mm
(20-1/2”)
80 mm
(3-1/8”)
520 mm
(20-1/2”)
35 mm
(1-3/8”)