Oemtools 24454 Operating Instructions And Parts Manual

Operating Instructions and Parts Manual 24454

Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect
yourself and others by observing all safety information, warnings, and cautions. Failure to comply with instructions
could result in personal injury and/or damage to product or property. Please retain instructions for future reference.

PPS-MARINE PERSONAL POWER

SOURCE WITH JUMPER CABLES

FOR CUSTOMER SERVICE

Technical Question?

CALL 1-866-458-2472

[e-mail]

UNPACKING

After unpacking unit, inspect carefully for any damage
that may have occurred during transit. Check for loose,
missing, or damaged parts. If any damage is observed, a
shipping damage claim must be filed with carrier.
Do not use the OEMTOOLS Portable Power Source if
broken, bent, cracked or damaged parts (including labels)
are noted. Any Portable Power Source that appears
damaged in any way, operates abnormally or
is missing parts should be removed from
service immediately. If you suspect that
the Portable Power Source was subjected
to shock load (a load that was dropped
suddenly, unexpectedly, etc.) immediately
discontinue use until it has been
checked by a factory authorized
service center.

WARNING

The following safety information is provided as a guideline to help you operate your Portable Power Source under the
safest possible conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe
handling instructions are not known or not followed. The following safety instructions are to provide the user with the
information necessary for safe use and operation. Please read and retain these instructions for the continued safe use
of your service system. Failure to follow instructions listed below may result in serious injury. In addition, make certain
that anyone that uses the equipment understands and follows these safety instructions as well.

Explanation of Safety Signal Words

WARNING
CAUTION

CAUTION
Notes

: Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

: Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury.

: Used without the safety alert symbol indicates a potentially hazardous situation which, if

not avoided, may result in property damage.

: Provide clarity and helpful information.

WARNING Pursuant to California Proposition 65, this product contains chemicals known to the state of

California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

3/16

2016 ©OEMTOOLS

Operating Instructions and Parts Manual 24454

PPS-MARINE PERSONAL POWER

SOURCE WITH JUMPER CABLES

Thank you very much for choosing an OEMTOOLS
Product!

For future reference, please complete the owner’s
record below:

Model: _______________ Purchase Date: _______________

Save the receipt, warranty and these instructions. It is
important that you read the entire manual to become
familiar with this product before you begin using it.
This machine is designed for certain applications only.
OEMTOOLS cannot be responsible for issues
arising from modification. We strongly recommend
this machine is not modified and/or used for any
application other than that for which it was
designed. If you have any questions relative to a
particular application, DO NOT use the machine until
you have first contacted OEMTOOLS to determine if
it can or should be performed on the product.

For technical questions please call 1-866-458-2472.

IMPORTANT INSTRUCTIONS
AND SAFETY RULES

1. Know your tool. Read this manual carefully. Learn
the tool’s applications and limitations, as well as,
potential hazards specific to it.

2. Keep work area clean and well lit. Cluttered or dark
work areas invite accidents.

3. Keep children away. All children should be kept
away from the work area. Never let a child handle
a tool without strict adult supervision.

4. Do not operate this tool if under the influence
of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or
reflexes are impaired while taking drugs. If there is
any doubt, do not attempt to operate.

5. Use safety equipment. Eye protection should be
worn at all times when operating this tool. Use ANSI
approved safety glasses. Everyday eyeglasses are
NOT safety glasses. Dust mask, non-skid safety
shoes, hard hat or hearing protection should be used
in appropriate conditions.

6. Wear proper apparel. Loose clothing, gloves, neck­ties, rings, bracelets or other jewelry may present a
potential hazard when operating this tool. Keep all
apparel clear of the tool.

7. Don’t overreach. Keep proper footing and balance
at all times when operating this tool.

8. Check for damage. Check your tool regularly. If
part of the tool is damaged it should be carefully
inspected to make sure that it can perform its
intended function correctly. If in doubt, the part
should be repaired. Refer all servicing to a qualified
technician. Consult your dealer for advice.

9. Keep away from flammables. Do not attempt
to operate this tool near flammable materials
or combustibles. Failure to comply may cause
serious injury or death.

10. Store idle tools out of the reach of children and
untrained persons. Tools may be dangerous in the
hands of untrained users.

• Maintain tools with care.

• Keep tools dry and clean.

• Do not use a damaged tool. Tag damaged tools “Do

not use” until repaired.

• Use only accessories that are recommended by the

manufacturer for your model. Accessories that may
be suitable for one tool may become hazardous
when used on another tool.

• Tool service must be performed only by qualified repair

personnel. Service or maintenance performed by
unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement

parts. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of injury.

• Maintain a safe working environment. Keep the

work area well lit. Make sure there is adequate
surrounding workspace. Keep the work area free of
obstructions, grease, oil, trash, and other debris. Do
not use this product in a damp or wet location.

• Maintain labels and nameplates on this product.

These carry important information. If unreadable or
missing, contact OEMTOOLS for a replacement.

• Before use, read and understand all warnings, safety

precautions, and instructions as outlined in the
vehicle manufacturer’s service manual. It is beyond
the scope of this manual to properly describe the
correct procedure and test data for each vehicle.

• Always perform vehicle service in a properly

ventilated area. Never run an engine without proper
ventilation for its exhaust. Stop work and take
necessary steps to improve ventilation in the work
area if you develop momentary eye, nose, or throat
irritation as this indicates inadequate ventilation.

3/16

2016 ©OEMTOOLS

2

Operating Instructions and Parts Manual 24454

PPS-MARINE PERSONAL POWER

SOURCE WITH JUMPER CABLES

WARNING

• Engine parts that are in motion and unexpected
movement of a vehicle can injure or kill. When
working near moving engine parts, wear snug fit
clothing and keep hands and fingers away from
moving parts. Keep hoses and tools clear of moving
parts. Always stay clear of moving engine parts.
Hoses and tools can be thrown through the air if not
kept clear of moving engine parts. The unexpected
movement of a vehicle can injure or kill. When
working on vehicles always set the parking brake or
block the wheels.

• Avoid accidental fire and/or explosion. Do not smoke
near engine fuel and battery components.

NOTE: The manufacturer declines any and all
responsibility for damage to vehicles or components if
said damage is the result of unskillful handling by the
operator or of failure to observe the basic safety rules
set forth in the instruction manual.

WARNING

Read Rules for Safe Operation and Instructions Carefully.

PERSONAL PRECAUTIONS AND SAFETY

• Working in vicinity of a lead-acid battery is dangerous.
Batteries generate explosive gases during normal
battery operation. For this reason, it is of utmost
importance that each time before using your Portable
Power Source, you read this manual and follow the
instructions exactly.

WARNING

Wear complete eye protection and clothing protection,
when working with lead-acid batteries.

1. Use only attachments recommended or sold by

manufacturer. Use of non-recommended attachments
may result in fire, electric shock or injury.

2. Do not disassemble the Portable Power Source.

Take it to a qualified professional when service or
repair is required. Incorrect reassembly may result
in electric shock or fire.

3. To reduce risk of electric shock, unplug charger

from outlet before attempting any maintenance
or cleaning.

4. Make sure someone is within range of your voice

or close enough to come to your aid when you
work with or near a lead-acid battery.

5. Have plenty of fresh water and soap nearby for
use if battery acid contacts skin, clothing, or eyes.
If battery acid contacts skin or clothing wash
immediately with soap and water.

6. Avoid touching your eyes while working with a
battery. Acid particles (corrosion) may get into your
eyes! If acid enters your eye, immediately flood
eye with running cold water for at least 10 minutes.
Get medical attention immediately.

7. Remove all personal metal items such as
rings, bracelets, necklaces, and watches when
working with a lead-acid battery. A lead-acid
battery can produce a short-circuit current
high enough to weld a ring (or the like) to
metal, causing a severe burn.

8. Take care not to drop a metal tool or other metal
onto the battery. Metal may cause sparking or
short circuit the battery or another electrical
devise. Sparking may cause an explosion.

9. NEVER smoke or allow a spark or flame in

the vicinity of the battery or engine. Batteries
generate explosive gases!

GENERAL BATTERY SAFETY

• To reduce the risk of battery explosion, follow
these instructions and those published by the
manufacturer and the manufacturer of any
equipment you intend to use in the vicinity of
a battery. Review cautionary marking on these
products and on the engine.

• When connecting to a battery in the vehicle, take
care to determine which post is grounded. To
reduce risk of a spark near battery, follow these
steps when battery is installed in vehicle.

•

WARNING: A spark near a battery may cause battery
explosion.

1. Stay clear of fan blades, belts, pulleys, and other
parts that can cause injury.

2. Check polarity of battery posts. Battery case will
be marked by each post: POSITIVE (POS, P, +)
and NEGATIVE (NEG, N, -). NOTE: The positive
battery post usually has a larger diameter than the
negative post.

3. Determine which post of battery is ground
(connected) to chassis.

NOTE: The negative post is normally grounded.

3/16

2016 ©OEMTOOLS

3

Operating Instructions and Parts Manual 24454

PPS-MARINE PERSONAL POWER

SOURCE WITH JUMPER CABLES

IMPORTANT SAFETY INSTRUCTIONS

The warnings, precautions, and instructions discussed
in this manual cannot cover all possible conditions
and situations that may occur. The operator must
understand that common sense and caution are
factors which cannot be built into this product, but
must be supplied by the operator.

DISPOSAL

At the end of the useful life of the OEMTOOLS Portable
Power Source, dispose of the components according
to all state, federal, and local regulations.

PURPOSE

The OEMTOOLS PPS-Marine Portable Power Source
24454 is a power source that is pocket sized but powerful
enough to start a car, light duty truck, motorcycles, boat or
ATV many times and can also charge cell phones, tablets
and cameras. Comes in an air tight storage case that is
perfect for boating or outdoor use.

PRODUCT SPECIFICATIONS

Size

Weight

Battery Capacity

Output

Input

Full Charging
Time

Starting Current

Peak Current

Operating
Temperature

6.3” x 3.0” x 1.1”

14.8 Ounces

44.4Wh

5V=2A; 12V=10A

14V=1A

3 Hours

200A

400A

-5°F ~ 140°F

Portable Power Source. If your vehicle will not
start, check for other problems.

4. DO NOT connect the two clamps. Otherwise, it
may be dangerous!

5. DO NOT disassemble the OEMTOOLS Portable
Power Source. Otherwise, it may be dangerous!

6. This power source is not intended for use by young
or infirm persons without supervision.

7. Do not use as a toy.

8. Do not allow the power source to become wet.

9. Do not immerse power source in water.

10. Do not operate the power source in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust.

11. Do not expose the power source to heat. Do not
store in locations where the temperature may
exceed 70°C.

12. Charge only at ambient temperatures between

-5°F ~ 140°F. Charge only using the charger
provided with the power source.

13. At the end of their useful life, discard the power
source with due care for our environmentCharge
only using the charger provided with the
OEMTOOLS Portable Power Source.

14. Under extreme conditions, battery leakage may
occur. Carefully wipe the liquid off using a cloth
and avoid skin contact when you notice liquid
on the batteries. In case of skin or eye contact,
rinse immediately with clean water and seek
medical attention.

15. Do not attempt to jump start Diesel Engines.

16. Always disconnect the jumper cables from the
Personal Power Source when finished jump
starting. Never store the Personal Power Source
with jumper cables attached to the battery source.

WARNING

1. Always make sure the blue plug of the jumper
cable is fully engaged in the jump start socket
before jump starting the vehicle. This can limit the
available power and may cause damage or melting
of the blue plug.

2. Always make sure jumper clamps are well
connected, check if the vehicle’s battery
connections are rusted or dirty and if necessary,
clean before jumping start the vehicle.

3. DO NOT attempt to jump start more than 3
times. Otherwise, it can damage the OEMTOOLS

3/16

2016 ©OEMTOOLS

4

Operating Instructions and Parts Manual 24454

PPS-MARINE PERSONAL POWER

SOURCE WITH JUMPER CABLES

INDICATOR

Press the switch to
check the charge level
of the OEMTOOLS
Portable Power Source.

The indicator lights
will flash one by one
during charging.
Different number
of solid indicators
show charge level of the OEMTOOLS Portable Power
Source. All indicators light up when the charging is
paused or completed.

Indicator Storage Level

Unlit 0%

5 Flashing 10%

1 Solid 20%

2 Solid 40%

3 Solid 60%

4 Slolid 80%

5 Solid 100%

OPERATING INSTRUCTIONS

IMPORTANT! Charge immediately after purchase, after
each use and every 3 to 6 months to keep the internal
battery fully charged and to prolong battery life.
The OEMTOOLS Portable Power Source Charging
Instructions:

1. Plug the home adapter into the universal socket.

2. Connect 12V 1A input port of the OEMTOOLS
Portable Power Source to the other end of
home adapter.

OR

3. Plug the car adapter into the socket of
cigarette lighter.

4. Connect 12V 1A input port of the OEMTOOLS Portable
Power Source to the other end of car adapter.

4. Attach clips to battery post and twist or rock
back and forth several times to make a good
connection. This helps to keep clips from slipping
off terminals and helps to reduce risk of sparking.

5. Plug the cord of jumper cable into the jump
start socket.

6. Start the vehicle.

7. When the vehicle is started, remove jumper cable
from the OEMTOOLS Portable Power Source and
disconnect red and black clamps from the vehicle
battery terminals.

8. Leave the vehicle’s engine running.

CHARGING CELL PHONE OR TABLET
INSTRUCTION:

1. Plug the pigtail cable B into the USB 5V 2A
output port.

2. Select appropriate connector and connect it to
your mobile phone or tablet.

3. Press the switch button to charge.

FOR POWER SUPPLY TO 12V VEHICLE

JUMP START 12V GASOLINE VEHICLE
INSTRUCTIONS:

1. Make sure that the number of indicators is not less
than 3 bars.

2. Connect POSITIVE (RED) clip from Portable Power
Source to POSITIVE (POS, P, +) ungrounded post
of battery. Connect NEGATIVE (BLACK) clip to
vehicle chassis or engine block away from battery.
Connect to a heavy gauge unpainted metal part of
the frame or engine block.

3. WARNING: Do not connect clip to carburetor,

fuel lines, or sheet metal body parts.

3/16

2016 ©OEMTOOLS

ACCESSORIES OR 12V ELECTRONICS

1. Plug the optional pigtail cable to 12V 10A
output port.

2. Connect the optional pigtail cable and 12V vehicle
accessories or 12V electronics.

3. Press the switch button to power supply.

LED FLASHLIGHT

1. Press the switch 3 seconds to start the LED
flash light.

5

Operating Instructions and Parts Manual 24454

Compositio n and amount of to xic and harmful substances in "The Tiny"

Portable Power Source

Pb Hg Cd Cr(Vi) PBB PBDE

0 0 0 0 0 0

0: Indicate all homogeneous ma terials' hazardo us substances co ntent are

below the MCV limit specified in the Standard 2002/95/EC (RoHs).

PPS-MARINE PERSONAL POWER

SOURCE WITH JUMPER CABLES

Figure Description Quantity

A

B

Portable Power
Source Battery Unit

5V-2A USB Port with
Pigtail Adapters

1

1

C Wall Charger 1

D Auto Charger 1

E Jumper Cables 1

F Watertight

1

Storage Case

G Rubber Bumper 1

(F)
Watertight
Storage Case

(E)
Jumper Cables

(G)
Rubber Bumper
(Battery Unit Not Included)

(A)
Portable Power
Source Battery Unit

(B)
5V-2A USB Port with
Pigtail Adapters

(C)
Wall
Charger

(D)
Auto Charger

TOXIC AND HARMFUL SUBTANCES:

Composion and amount of toxic and harmful substances in the

Mul-Use Portable Power Source with Jumper Cables.

TROUBLE SHOOTING:

Problem Cause Remedies

The OEMTOOLS
Portable Power
Source is still not
fully charged while
it’s 5 indicator
lights are solid.

No response
when pressing the
switch button.

3/16

2016 ©OEMTOOLS

Charger may auto
stop at 60% if
battery is very
low to prevent
damage.

Low voltage
protection of
the OEMTOOLS
Portable Power
Source.

Unplug the adapter
and plug it in again.

Plug the adapter into
the 12V 1A input port
to activate.

MAINTENANCE

Very little maintenance is required for the OEMTOOLS
Portable Power Source. Follow common sense in
wiping the charger clean and store in a clean, dry area.

1. After use, wipe all battery corrosion and other dirt
or oil from clip, cord, and the OEMTOOLS Portable
Power Source case. Use a dry cloth.

2. Coil charger cords to prevent damage.

3. Replace any cracked or frayed cords.

4. Store the OEMTOOLS Portable Power Source in a
clean, dry area.

6

Operating Instructions and Parts Manual 24454

PPS-MARINE PERSONAL POWER

SOURCE WITH JUMPER CABLES

OEMTOOLS™ 90 DAYS LIMITED WARRANTY

From 90 days from the original purchase of this product, OEMTOOLS will warranty this item. If you find any
defect in material or workmanship, through normal usage, return it to the place of purchase or to OEMTOOLS
for repair or replacement at our discretion. In order to obtain this service send your tool and proof of purchase,
transportation pre-paid, to OEMTOOLS Q.A. Dept., 3580 E. Raines Road #3, Memphis, TN 38118. We will not
be responsible for lost or damaged goods during transportation, please insure your package. If our inspection
verifies the defect, we will either repair or replace the product at our election, or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products
at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the
scope of our warranty, then you must bear the cost of returning the product.

OEMTOOLS does not provide warranty for products labeled other than OEM or OEMTOOLS. OEMTOOLS will
not provide any warranty for products subjected to abnormal use. Abnormal use includes, but is not limited to,
abuse, accident, alteration, neglect, and unauthorized or unreasonable use or repairs. This warranty does not
cover bits, blades, files, batteries, or calibration. We recommend that you maintain your tools and sharpen or
replace blades, bits, files, and batteries as necessary. OEMTOOLS reserves the right to makes any changes in
construction or design at any time without any obligation in incorporating such changes to tools or equipment
previously sold.

OEMTOOLS makes every effort to assure that its products meet high quality and durability standards, and
warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear or to lack of maintenance.

We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS
WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS. This warranty gives you specific legal rights, and you may
also have other rights, which vary from state to state.

• Consumable components such as batteries are not covered by the warranty.

• This warranty is invalidated if any of the following occurs, but not limited to this list:

• Failure to follow instructions in the User’s Manual

• Accidental and or unreasonable use or misuse

• Mishandling

• Over charging or overloading

• Extended storage without recharging

• Repairs by and un-authorized person or any modification

• Normal wear or accident

3580 E. Raines Road, Suite 3, Memphis, TN 38118

[e-mail]

3/16

2016 ©OEMTOOLS

CONTACT US

Tel: [phone]

7