OEM N330 User Manual

OEM ITX-945GC3B N330 Motherboard

User’ s Manual V1.0

The ownership of all parts of this product, including the accessories and software, is enjoyed by OEM production Electronics Co. Ltd. Imitating, replicating, abstracting or transferring of the product is not permitted without the consent of OEM. The product specifications and other information provided in this Manual are only used for reference and shall be subject to change without prior notice.

The names mentioned in this Manual are only used for purpose of identification. Some of them may be the trademarks of other companies, or their copyrights are owned by those companies.

We will be appreciate if we are informed about any error or ambiguous description in whichever part of this Manual,

including that of the hardware and software.

Service hot line (US): 800-664-8917 Email: info@OEMproduction.com

Contents

I. About the product

1. Gratitude 1

2. Accessories 1

3. Picture of the motherboard 2

4. Features 3 System processor System memory System BIOS Interface of peripheral equipment Power management Expansion slot

II. Installing hardware

1. Layout of motherboard 6

2. Installing memory card 7

3. Installing extension interface card 8 Installing PCIE video card

4. Setting motherboard’s jump wire and inserts 9 SATA1/SATA2/SATA3/SATA4 (Serial ATA wire-harness receptacle)

CPU_FAN1/SYS_FAN1(CPU fan’s receptacle / system fan’s receptacle)

CLR_CMOS(CMOS pin) F_USB1/ F_USB2(Frond-end USB pin) F_ AU DI O(Pin for front-end sound card) A TX 24 P(Power receptacle) F_ PA NE L(Front-end control panel) I D E 1 (Wire-harness receptacle for hard disk)

5. Rear interfaces of motherboard 1 4

III. BIOS Setup

1. Main menu 1 6

2. Standard CMOS setup 1 8

3. Advanced BIOS setup 18 CPU Configuration 1 8 IDE Configuration 1 9 IO Chip Configure 2 0 PC Health Configuration 2 1

4. Power management 2 2

5. BOOT setup 2 3

6. Security setup 2 5

7. Chipset setup 2 6

8. Exit 2 8

IV. Installing software

1. Installing driver for motherboard 2 9 Installing driver for main chip 3 0 Installing driver for sound card 3 0 Installing driver for on-board network interface card 3 1 Installing driver for video card 3 1

2. HD-AUDIO sound card setup 3 2

Chapter I

About the Product

1.1 Gratitude

Thank you for purchasing ITX-945GC3B N330 Motherboard made by OEM. Employing INTEL 945GC+ICH7 and on-board IN TEL A tom N330 CPU, this product supports front-end wire harness 1066MHz, dual-channel memory standards of DDR II 667/533 and USB2.0, and is built with onboard HD-AUIO sound card.

1.2 Accessories

Your Mini ATOM N330 Motherboard consists of the following accessories. If any of them is missing, please contact your local distributor as soon as possible.

1. ITX-945GC3B N330 Motherboard

2. User’s Manual V1.0 for Mini ATOM N330 Motherboard

3. W arranty Card/QA Card

4. Data cable for hard disk (80-Pin)

5. SATA hard disk cable

6. Driver’s disk

One piece One copy One for each One piece One piece One piece

3. Picture of the motherboard

Note: The above figure is the picture of ITX-94GC3B motherboard.

This picture is only used for reference and the physical object shall prevail.

4. Features

System processor

1) Built with on-board INTEL Atom N330 CPU

System memory

1) Supports one 240-Pin DDR

2) Supports 2GB of memory at maximum;

3) Supports single-channel memory mode.

System BIOS

1) Supports PNP, APM and ATAPI;

2) Supports ACPI and DMI;

3) Automatic detection and supporting hard disk the LBA mode of which is over 160G;

4) Easy for end-users to upgrading the motherboard with BIOS.

Interface of peripheral equipment

1) One quick IDE port, supporting DMA33/66/100 hard disk,

CD-ROM, ZIP, LS120 and other drivers;

2) Integrated with PCIE kilo-mega network interface card

(RTL8111C);

3) One 16650-compatible UART serial interface;

4) Supports 4 SATA II hard disk interface;

5) 6 high-speed transmission ports (max. 480Mb/s) which sup-

port USB2.0, compatible with USB1.1;

6) One PS/2 keyboard connector;

7) One PS/2 mouse connector;

8) One CMOS pin;

9) One receptacle for system fan;

10) One interface for case panel, compatible with HDD LED and

Speaker.

II 667/533 memory;

11) On-board HD-AUDIO sound card:

(1) Integrating HD-AUDIO sound-effect controller; (2) Supports Director Sound and Sound Blaster; (3) Supports NPN and APM 1.2; (4) Supports Win2000/XP/Vista driver; (5) Supports Line-in, Line-out and Mic-in; (6) Supports front audio ports.

Power management

1) Supports APM and ACPT;

2) Compatible with “Green PC”.

Extended interface

One PCI Express x16 graphics card interface.

Chapter II

Installing Hardware

Warning

The motherboard consists of a great number of ICs and other components. These ICs are apt to be damaged by the static charge. Therefore, the user must make the following preparations before formal installation:

1. Turn off the power of the computer. It is preferable the power cord be unplugged.

2. Take care not to contact the metal wires and theirs joints on the motherboard when handling it.

3. It is preferable that the anti-static wrist strap be worn.

4. Before the ICs are installed, the components of the motherboard should be placed on the anti-static mat or bag.

5. When you remove the plug on the ATX power supply of the motherboard, make sure the switch of the power supply is in OFF state.

Installing the motherboard onto the computer case: For most of the computer cases, the multiple fixing holes left on their bottoms can be used for securing the motherboard and no short circuit can occur therefrom. During your operation, take care not to allow the screws to contact any circuit or part on PCB. When circuits on the surface of the motherboard get close to the fixing holes, you can use the plastic sheet to separate the screws from the board surface so as to avoid damage or failure of the motherboard.

1. Layout of motherboard

2. Installing memory card

Please install the memory card in accordance with the following procedures:

1) Remove the white tenon at the two ends of the interface slot for the memory card;

2) Align the golden finger of the memory card to the throve of the interface slot and pay attention the concave hole of golden finger should be aligned to the convex point of the slot;

Remove outward the white tenon at the two ends of the interface slot for module of the memory card.

3) Finally, insert the memory card into the interface slot gentlely. If no error occurs at the moment, insert the card forward in the slot till the white buckle is automatically engaged in the concave hole at the two sides of the memory card.

Note

In order to avoid damages to the motherboard or the components, the user must make sure the power supply to the computer is turned off before the memory card or other system component is installed or removed. As the throve is set at the golden finger of the DDR DIMM memory card, the memory card can only be inserted into the slot with one direction. During installation, the user only needs to align the golden finger and the dual-channel throve of the interface slot and insert it gentlely. To avoid damage, never apply excessive force in that process.

3. Installing extension interface card

Installing graphics card

This motherboard provides one interface slot for PCIEx 16 graphics card. When you install the PCIE graphics card, you should note that throve of the golden finger must be exactly engaged into the interface slot. In that process, it is preferable that you be in grounded state, and you should carefully take out the graphics card from the anti-static bag. Then align the graphics card to the PCIE interface slot and insert it. After that, tighten the screw on the metal baffle.

Bracket Screw

Graphics card

Motherboard

4. Setting motherboard’s jump wire and inserts Note

The user should note that all receptacles are marked with PIN1. The symbol “#” indicates the ex-factory default value of the motherboard.

1) SATA1/SATA2/SATA3/SATA4 (Serial ATA wire-harness receptacle)

Serial ATA receptacle can offer a transmission speed of 300MB/sec. You can connect the Serial ATA devices to this receptacle.

2) CPU_FAN1/SYS_FAN1(CPU fan’s receptacle)

This receptacle can be used for connecting CPU/system fan. Its pins’ function are defined below. The user shall make sure the fan is conforming.

+ 26 hidden pages

OEM N330 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual