Odyssey Oblivion NX, ODY-2017BF1 Installation Manual

FOR AGES

14

+

WHAT’S IN THE BOX

1
2
3
4
5

Oblivion NX Drone Unit

2.4 Ghz Radio Transmitter
USB Charging Cable

3.7V Rechargeable Lithium Battery
Spare Propellers & Micro Screwdriver

360º FLIP
(see page 4)

INITIATE HOMEBEACON®
(PRESS & HOLD FOR 3 SECONDS,
see page 5 for details)

INITIATE SMARTFLY®
(PRESS & HOLD FOR 3 SECONDS,
see page 5 for details)

IGNITION

SIDE TRIM

DIRECTION CONTROL STICK

FORWARDS / BACKWARDS TRIM

SPEED

(3 SETTINGS)

DIRECTION TRIM

POWER SWITCH

THROTTLE STICK

POWER LED

Thank you for your purchase of the Oblivion NX Live
Streaming HD Video Drone. You’re just moments away
from creating stunning aerial acrobatics!

5

INSTRUCTION & REFERENCE MANUAL • Model no. ODY-2017BF1

CHARGING THE Oblivion NX DRONE

SETUP OVERVIEW RADIO CONTOL TRANSMITTER •BATTERY INSTALLATION

If the Radio Control Transmitter will not be used
for extended periods of time, please remove the
batteries.

Please use 4 AA batteries. Use
the polarity markings to install
in the correct orientation. Do
not mix batteries of different
types.

Unscrew the screw
holding the battery lid to
the body. Then lightly pull
the clip down to pull the
lid away from the
transmitter body.

Insert 4xAA batteries into
the battery compartment,
making sure to match the polarities. Then replace the lid and
firmly tighten the screw to secure the battery compartment.

NOTICE

NOTICE

The Oblivion NX battery comes partially charged and is ready to fly. Skip to Remote

Control Battery Installation section and use your Seeker now. Use this charge

completely before charging the Galaxy Seeker battery for the first time.

WE RECOMMEND!

1. Locate the battery compartment under the tail of the Drone. Open the lid by pulling up on the tab.

2. Gently extend the red connector without tugging on the wire.

3. Connect the red-and-black tip of the USB charging cable to the red connector in the tail of the Drone. Please note: Not all USB
ports provide power. Typically, only ports mounted on a computer and not through a peripheral will provide enough power for
charging.

4. After charging the battery, disconnect the USB cord and carefully, without pulling on the internal wire, disconnect the battery
cord and close the battery compartment lid.

CAUTION: Battery may be hot if being disconnected right after use. If hot, then wait a few minutes to let the battery cool down.

When charging with the included USB cable, the LED light will light up red,
indicating it is charging. Once charging is complete, the LED light will tur n

off. Discontinue charging immediately.

Rechargeable Lithiu m

Polymer Battery

3.7V / 7 00 mAh

Please check the AA batteries routinely. If the AA
batteries are left within the Radio Control Transmitter,
potential leakage and/or corrosion may occur, which
can damage the transmitter and create a fire hazard.

Attach the X-Guard propeller defense system.

STEP 1

Install batteries into the radio control transmitter.

STEP 2

Charge the Oblivion NX and monitor.

STEP 3

Attach the monitor to the radio control

transmitter when charging is complete.

STEP 4

CAUTION

WARNING

ATTACHING YOUR SMARTPHONE to the PHONE HOLDER

PAIR THE UNITS & START TO FLY

Step 1: Switch on the Drone. The LED lights will start to blink.
Step 2: Turn on the Remote Transmitter. Its power light will illuminate. Wait 7 seconds for the electronic gyro to
stabilize*.
Step 3: Push the throttle (left) stick up to the 12 o'clock position and then down to the 6 o'clock position. As the remote
transmitter searches for the Drone, the power light on the transmitter blinks rapidly.
Step 4: Connection is complete once the power light and the LEDs on the Drone stop blinking. You're ready to fly!

Your Oblivion NX WiFi Live Streaming HD Drone comes with a plastic smartphone holder equipped with suction
cups that lets you view the Oblivion NX’s footage as it flies. This is done via the Odyssey VR app that you can
download for free. Please refer to the Odyssey VR 3D App Guide included in your package for further instructions
on how to utilize the free app with your drone.

Take the back of your smartphone and press the back firmly into the suction cups to make sure it
has a secure hold. Attach the smartphone holder to your remote control transmitter, start up the
Odyssey VR app and you are good to go!

Be sure to place the quadcopter on a level surface to ensure a proper and neutral alignment of the gyro.

NOTICE