RAIDER
ASSEMBLY
INSTRUCTIONS
Model Year: 2015
Model Engine Size Category
2 Door 800cc/1000cc Off-road
IMPORTANT INFORMATION
The assembly instructions in this guide are for the Raider models only. Please make sure a PDI was
performed on each unit before the assembly begins.
ALSO
• Do PDI with customer before unit leaves.
• Fill out proper warranty registration completely with customer (explain to them in detail what coverage they have.)
• Submit to ODES within 5 days.
• Go over maintenance charts with customer.
Uncrating/ Removing Parts
1-1
Carefully remove the tarp and plastic wrap
covering the crate.
Pop off all of the tabs from the crate bars.
Once all tabs are removed the crate bars
will fold open and you can begin removing
them.
Uncrating/ Removing Parts
1-2
Once you have fully uncrated your Raider,
you can begin to remove all loose parts.
There are loose parts on the inside, frame
and underneath the unit, please be sure to
remove everything.
The fender ares will be zip tied to the rear
fender area.
Bottom Plate Removal
Lift the Raider slighty off the ground to
begin unbolting the bottom plate of the
crate.
Unbolt the brackets on all 4 hubs to detach the Raider from the bottom plate.
Once all hubs are unbolted, you can now
lift the Raider higher and begin putting on
the shocks.
Toolbox/ Bolt Bags
The bolt bag is located underneath the
passenger side seat plate.
Remove the plate and toolbox cover. Once
removed, you can begin removing the bolt
bags from the toolbox.
Be sure all bags are accounted for, a bolt
bag form should come with your UTV. If
you cannot locate the bolt bag form, you
can download it on our website www.
odesutvs.com underneath SUPPORT > My
Dealer Services.
Shocks 1-1
Once your UTV is raised off the ground
and all the nessacary bolts are accounted
for, you can begin to put the front and rear
shocks on.
When unboxing the shocks it is important that you immediately identify which
shocks are the rear and front to pair them
accordingly.
Once you have the shocks paired with
their partner, we suggest laying the front
shocks down by the front hubs and rear
shocks down by the rear hubs.
Shocks 1-2
Once all of your shocks are in place you
can begin to place the shocks in the arms
and bolt them down.
Remember to bolt both the top and bottom
of the shocks into place.
Once you have bolted down all shocks be
sure to tighten the bolts to eliminate any
unwanted play.
Tires
Once the shocks are securely attached to
the unit, you can now begin to put on the
tires. Please make sure to inate the tires
to 15psi before bolting onto the unit.
Once you have all 4 tires bolted on, you
will need to tighten all of the bolts with a
torque wrench.
Battery Box
Once the unit is back on the ground, you
can begin attaching the battery box to the
frame.
There are 4 bolts that connect the battery
box to the frame. Two on the left side and
two on the right side, be sure to bolt all 4
bolts down and tighten them.
Front Bumper 1-1
Once the battery box is bolted down you
can now attach the front bumper to the
frame.
Make sure all holes and brackets align in
their positions.
Bolt down the two bottom holes rst to
help keep the bumper in place.
Front Bumper 1-2
From there, slowly work your way up the
bumper applying bolts where nessacary.
Once you have placed all bolts in positon,
drill all bolts into place to secure the front
bumper down.
Auxilary Tank/ Radiator Cap
Once the front bumper is in place, you can
now attach the auxilary tank and radiator
cap.
Simply line the auxilary tank up with with
the brackets shown in the image and
tighten the screws.
The same procedure applies for the radiator cap.
Radiator Guard/ Shields
You can now attach the front radiator
guard, radiator shields and horn. Align the
radiator with the holes on the frame.
Align the left and right shields with the
holes on the radiator guard and bolt them
down.
On the driver side shield, be sure to bolt
down the horn on the driver side radiator
shield. Once all bolts are in place tighten
them and wire the horn.
Passenger Handlebar
Align the bar with the two holes on the
dash as seen in the image.
Make sure you push the bar all the way
through and align it with the bracket on
the other side of the dash.
Once the bar is in place and aligned as
shown in the image, you can begin bolting down the bar on both the left and right
side. Be sure to tighten all 4 bolts.
Hood 1-1
You can now begin attaching the hood.
First place all of the hood clips on the
provided holes located on the top of the
dashboard. The holes run across the entire UTV. Be sure to not miss or skip any
of the hood clips, these clips help make
the screw secure once the hood is in
place.
Once all clips are inserted you can now
place the hood on the unit. Make sure all
holes line up.
Hood 1-2
Once the hood is aligned start off by securing the driver and passenger sides of
the hood.
Once the driver and passenger sides are
secure you can begin making your way
across the entire hood. Be sure to not accidently miss or skip over any holes.
Once the top of the hood is secure you
will also need to secure the area in which
the hood cover will lay. Refer to the image
for location.
Front Fender Flares
Place the clips in the area in which the
front fender ares will go.
Once all 4 clips are in place, you can
begin to secure the fender are onto the
unit.
It is easy to forget the front screw under-
neath the fender are, please be secure to
double check and secure this one as well.
Front Winch 1-1
Place the winch bracket on the front bumper and align it with the holes provided.
You can then place the winch on top of the
bracket and wire the winch.
Once the winch is in place you can secure
the bracket down.
Once the winch is secure, you can now attach the front winch plate.
Front Winch 1-2
Clip the hook onto the winch wire as
shown in the image.
Tighten all bolts completely securing the
winch in place.
Attach the stopper to the winch wire, test
whether your winch is operational or not
and pull the wire back in.
Rear Hitch
Push the hitch into the hitch bracket provided in the rear.
Make sure the holes on the hitch are
aligned with the holes on the hitch bracket
Secure the hitch with the clip.
Front Bumper Guard
Align the bumper guard on the front bumper.
Secure the bumper guard down with 4
screws.
Tighten the 4 screws to hold the front
bumper in place.
Taillights/ Rear Fenders 1-1
Insert the clips on the tailight panel.
Align the tailight panel with the unit.
Once the tailight panel is in place you can
begin to secure it with screws going all
across the top, sides and middle.
Taillights/ Rear Fenders 1-2
Do not forget to secure the rear driver and
passenger sides of the taillight panel as
shown in the image.
Place the clips for the rear fender are.
Align the rear fender are underneath the
tailight panel and cargo bed and secure it
with the nessacary screws.
Taillights/ Rear Fenders 1-3
Secure the middle of the taillight panel
with 2 screws.
The middle of the tailight panel should be
the last section needing to be secured.
Please go back and check that you have
all areas secured and both passenger and
driver side rear fender ares installed.
Once the tailight panel and rear fender
ares are installed you can then connect
the taillight lights.
Rollcage Assembly 1-1
Unbolt the cross member attached to the
frame.
Assemble the rollcage by sliding the two
pieces together and aligning the holes.
Don’t forget to attach the lightbar brackets
before bolting everything together.
Rollcage Assembly 1-2
Place the rollcage onto the unit, make
sure to leave it a little loose so you can
push the bolts through the holes.
Once everything is aligned and in place
you can begin tightening all of the bolts.
Don’t forget to also tighten the lightbar
brackets.
Seatbelts
Unclip the zip tie holding the seatbelt together.
Pull the seatbelt down and align it with the
bracket at the bottom of the driver/ passenger side seat.
Bolt the seatbelt down and tighten the
bolt. Please make sure all bolts are properly tightened to ensure no play in the
seatbelts.
Windshield
Place the windshield on the hood of the
unit laying against the rollcage.
Assemble the brackets on both the passenger and driver side of the windshield.
There will be 6 brackets total on the windshield, 3 on the passenger side and 3 on
the driver side. Make sure you tighten all
bracket bolts.
Roof
Once the windshield is installed you can
now attach the roof.
Slide the roof on the top of the rollcage
and make sure it is properly aligned.
Secure the roof with the 5 roof brackets
provided. Be sure to tighten all bolts on
the brackets to ensure no roof rattle.
LED Lightbar
Attach the brackets to both sides of the
lightbar and ensure all nuts and bolts are
tightened.
Align the bracket on the roof and make
sure the lighbar is centered. From there,
you can begin to secure the lightbar down
from the inside of the roof. Make sure to
tighten all led lightbar brackets down.
Once the lightbar is completely secure,
you can begin running the wire through
the roof and down the passenger side of
the rollcage. Be sure to zip tie or secure
your wire in someway so it is not hanging
while riding.
Battery Box
Make sure the battery is fully secure by
tightening all the surrounding bolts.
Once all bolts are tightened you can begin
covering the terminals with the waterproof
covers and placing the battery box cover
over the battery box.
Battery Box Cover
You can now install the batery box hood
cover.
Make sure to properly align the cover with
the ridges in the hood before tightening
the hood down.
Tighten both passenger and driver sides
of the hood cover.
Seats
You can now place the storage box cover
over the storage box on the passenger
side.
Attach the bottom seat panels to both passenger and driver side seats. Make sure
you tighten all bolts holding the panel and
seat together.
Clip the seats into place.
Steering Wheel
Splin the steering wheel into the proper
position by making sure the wheels and
the steering wheel are straight/aligned.
Bolt down the middle of the steering
wheel.
Once the steering wheel is bolted down
you can screw on the steering wheel
cover.
Loading...