Octek SOCKET ROCKET 336 Reference Guide
Socket Rocket 336
™
COMMAND CARD
Connection Commands
Command Description
A Answer call
D Dial number
H Hang up modem
O Enter On-line state
Dial Modifiers
Dial Digits 0-9, A, B, C, D, #, *
, Pause while dialling
F or ^ Disable calling tones
L Redial last number
P Pulse dial number
R Switch to answer mode
S=n Dial stored number ‘n’ (where n=0-9)
T Tone dial number
W Wait for dial tone
; Return to Local command state
! Hook flash
@ Wait for quiet answer
General Commands
Command Description
+++ Escape Sequence
**** Universal Remote Access Sequence
? Displays help. May be followed by the command(s) or a
keyword for which help is needed
A/ Repeat Command
B0 ■ Auto-Connect
B1 Auto-Connect
B2 Auto-Connect
B3 V.21 - 300 bps
B4 Bell 103 - 300 bps
B5 V.23 - 1200/75 bps
B6 V.22 - 1200 bps
B7 Bell 212A - 1200 bps
B8 V.22bis - 2400 bps
B9 Auto-Connect
■ Indicates factory defaults
▲ Changing the default is not
allowed by Austel
☞ If no value is entered in a
command for ‘n’ or ‘x’, a
value of 0 is selected.
E
N
H
I
L
-
N
O
*
E
A
S
AT?
Y
C
O
M
E
M
E
R
A
N
D
B10 V.32 - 4800 bps
B11 V.32bis - 7200 bps
B12 V.32 (Non-TCM) - 9600 bps
B13 V.32 - 9600 bps
B14 V.32bis - 12000 bps
B15 V.32bis - 14400 bps
B16 V.34 - 14400 bps
B17 V.34 - 16800 bps
B18 V.34 - 19200 bps
B19 V.34 - 21600 bps
B20 V.34 - 24000 bps
B21 V.34 - 26400 bps
B22 V.34 - 28800 bps
B23 V.34 - 31200 bps
B24 V.34 - 33600 bps
E0 Local command state echo off
E1 ■ Local command state echo on
H1 Go off-hook
I0 Numeric firmware identity
I1 Checksum of firmware - return checksum
I2 Checksum of firmware - return OK/ERROR
I3 Modem Model
I4 Firmware Version and date
I5 Manufacturer ID
L
P
*
E
C
N
E
R
E
F
1
I9 Verbal firmware identity
I10 Modem Statistics
M0 Speaker is always off
M1 ■ Speaker on when connecting, off when connected
M2 Speaker always on
M3 Speaker off when dialling or after connection established
M4 Speaker on during dial, answer, retrain or rate change
O1 Enter On-line state and force communication retrain
O2 Retrain, don’t go on-line
P Pulse dialling
Q0 ■ Modem returns response codes
Q1 Modem does not return response codes
Q2 Modem does not return RINGING or response codes when
answering
R0 ■ Autobaud
☞ Although other R settings are accepted, the modem
always reads the terminal speed directly from the internal
16550UART.
Sn? Display value in S Register ‘n’
Sn=x Place ‘x’ in S Register ‘n’
T ■ Tone dialling
V0 Numeric response codes
V1 ■ Verbal response codes
2
W0 CONNECT message reports the terminal speed
W1 CONNECT message reports the terminal speed
W2 ■ CONNECT message reports the line speed
X0 Basic response codes (codes 0-4,8)
X1 Extended response codes (codes 0-5,8,10-12,30-40,60-62)
X2 Extended response codes (codes 0-6,8,10-12,30-40,60-62)
X3 Extended response codes (codes 0-5,7,8,10-12,30-40,60-62)
X4 Extended response codes (codes 0-7,10-12,30-40,60-62)
X5 ■ Extended response codes (codes 0-7,10-13,30-40,60-62)
X6 Extended response codes (codes 0-5,7-8,10-13,30-40,60-62)
Zn Restore configuration profile n (n=0,1,2,3)
&C0 DCD signal always asserted
&C1 ■ DCD signal responds to remote modem
&C2 DCD signal always on, pulses low on disconnect
&D0 Ignore DTR
&D1 Return to Local command state if DTR goes low
&D2 ■ Hang up and return to Local command state if DTR goes low,
&D3 Initialise with values in &Y profile if DTR goes low
&F0 Restore factory defaults
&F1 Restore non-error correction factory defaults
&F. Reset modem (clear security database/Telephone numbers)
&G0 ■ No guard tone generated
&G1 550 Hz guard tone generated
&G2 1800 Hz guard tone generated
&K0 Flow control disabled
&K3 RTS/CTS flow control
&K4 XON/XOFF flow control
&K5 Transparent XON/XOFF flow control
&K9 ■ Failsafe flow control
&M0 ■ Asynchronous mode
&M4 Asynchronous mode with stored number dialling
&N0 Abort dial character disabled
&N1 ■ Abort dial character enabled
&P0 39/61 make/break ratio (USA)
&P1 ■▲ 33/67 make/break ratio (Aus/UK)
&S0 ■ DSR signal always asserted
&S1 DSR signal asserted at start of handshake
&S2 DSR signal asserted at end of handshake (before CONNECT
&T0 Terminate test
&T1 Local Analog Loopback test
&T3 Local Digital Loopback test
&T4 Grant Remote Digital Loopback test
&T5 Deny Remote Digital Loopback test
&T6 Remote Digital Loopback test
&T7 Remote Digital Loopback & Self test
disable auto-answer until DTR asserted
message)
3
&T8 Local Analog Loopback & Self test
&V View active configuration profile
&Vn View stored profile (n=0-3)
&V8 View differences between active and default
&Wn Save current configuration into stored profile n (n=0,1,2,3)
&Yn Select stored profile n for Power on and &D3
&Zn=x Store x as phone number n (x=0-9)
#A0 Prevent remote access
#A1 Allow remote access
#A2 ■ Allow remote access with security password
#B0 ■ In 1200bps originate mode B0=V.23, B2=V.22
#B1 In 1200bps originate mode B0=V.22, B2=V.23
#C0 V.25 calling tones disabled
#C1 ■ V.25 calling tones enabled
#E0 ■ DES encryption disabled
#E1 DES encryption enabled
#E2 Super secure enabled
#J0 Assume V.42 compatibility
#J1 ■ Check V.42 compatibility
#O0 ■ Characters ignored if modem buffers overflow
#O1 Disconnects if terminal buffer overflows
#O2 Disconnects if line buffer overflows
#O3 Disconnects if either buffer overflows
#S Enter security menu mode
#V0 Command and S Register verifier off
#V1 ■ Command and S Register verifier on
%B0 ■ S0=0 setting after AT&F
%B1 S0=2 setting after AT&F
%C0 Compression disabled
%C1 MNP 5 compression enabled
%C2 V.42bis data compression enabled
%C3 ■ V.42bis data compression enabled with fallback to MNP 5
%Dn Set disconnect delay to n seconds (default %D0)
%E0 Disable auto-retrain
%E1 Enable auto-retrain
%E2 ■ Automatic Speed Stepping
%K0 ■ CTS operates normally
%K1 CTS off during dial and handshake
%L0 Report current received signal level (-dBm)
%Ln Set transmit level (n=11 to 19; -11dBm to -19dBm)
%P0 ■ CONNECT message appears before DCD asserted
%P1 CONNECT message appears after DCD asserted
%Q Report current line quality (EQM) (0=perfect)
%R0 ■ &R command determines state of CTS
%R1 CTS always follows RTS (not reset by &F)
%R2 CTS follows DTR when offline (not reset by &F)
%S0 ■ DSR is not overridden
4
%S1 DSR mimics the state of DTR (not reset by &F)
%T0 ■ DCD always follows state of carrier
%U0 ■ Standard error correction response codes
%U1 V.42 response codes when V.42 connection established
%U2 V.42 response codes for V.42 connections, MNP 2,4, compres-
sion & DES messages displayed
%W0 ■ Disable welcome message
%W1 Send message specified by *W to remote modem after connect
\A0 MNP block size = 64
\A1 MNP block size = 128
\A2 MNP block size = 192
\A3 ■ MNP block size = 256
\Bn Send Break sequence to remote modem (default \B3)
\J0 ■ Fallback to direct mode disabled
\J1 Fallback to direct mode enabled
\Kn Received Break control (default \K5)
\N0 Constant speed mode
\N1 Variable speed mode
\N2 MNP reliable mode
\N3 ■ V.42/MNP auto-reliable mode
\N4 V.42 reliable mode
\N5 V.42 auto-reliable mode
\N6 V.42/MNP reliable mode, fallback to MNP reliable mode
\N7 MNP auto-reliable mode
\Q0 Flow control disabled
\Q1 XON/XOFF flow control from modem and computer
\Q2 CTS flow control
\Q3 CTS-RTS flow control (same as &K3)
\Q4 Modem-only XON/XOFF flow control
\Q5 CTS flow control (CTS low until connection)
\Q6 CTS-RTS flow control - CTS low until connect
\S Display active configuration with detailed description
\Tn Set inactivity timer to n seconds (Default \T0)
\V0 ■ Disable reliable response codes
\V1 Enable reliable response codes
\V8 Extended response codes
\V9 Extended response codes with diagnostic information
\X0 ■ XON/XOFF pass through disabled
\X1 XON/XOFF pass through enabled
*A0 Conservative Automatic Rate Selection
*A1 ■ Medium Automatic Rate Selection
*A2 Aggressive Automatic Rate Selection
*Wttt...tt Specify welcome message text used by %W1
ttt...tt = text use | for new line (max. 80 characters)
5
S Registers
Reg Range Def Unit Function
0 0-255 0 rings Rings Before Answer
1 0-255 00 rings Ring Count (read only)
2 1-255 43(+) ASCII Escape Sequence Character
3 0-127 13 ASCII Carriage Return Character
4 0-127 10 ASCII Line Feed Character
5 0-127 08 ASCII Backspace Character
6 4-7 04 secs Wait for Dial Tone
7 1-60 30 secs Wait for Carrier
8 1-7 04 secs Delay for Pause Modifier
9 1-255 06 0.1secs Carrier Detect Response Time (fsk only)
10 1-255 18 0.1secs Lost Carrier/Hang Up Delay (fsk only)
11 70-254 95 msecs Touch Tone Timing
12 3-255 50 0.02secs Escape Sequence Guard Time
16 0-8 00 Test in Progress (read only)
18 0-255 00 secs Test Timer
25 0-255 05 0.01secs DTR Loss Detection Time
26 0-255 00 0.01secs RTS-CTS Delay
27 0-255 00 secs Delay Before Security Dial-back
29 10-100 50 0.01secs Hook Flash Duration (also sets S100)
30 0-255 00 10secs Inactivity Timer (data mode)
33 0-1 1 Retrain Disable = 0
38 0-255 00 secs Disconnect Delay
42 0-255 Modem Disconnect Reason (read only)
43 0-255 15 msecs Break Sequence Length
62 0-255 75 0.01secs V.42 detection timer
66 1-255 10 0.1secs Remote Access Guard Time
67 1-127 42(*) ASCII Remote Access Character
69 0-255 60 secs Command line timeout
74 0-255 Disconnect Reason Previous Call
75 0-255 0 0.01secs DTR active detection time
80 1-19 15 5% Flow Control High Water Mark
81 1-19 03 5% Flow Control Low Water Mark
82 1-255 60 bytes Failsafe Flow Control Overrun
95 0-63 0 bitmap Extended Result Codes
96 1-255 80 Help Page Width
97 1-255 24 Help Page length
100 1-10 5 100msecs Hook Flash Duration (also sets S29)
Use AT? to see the Command Set supported by your modem's version
of code. For a detailed description of the modem commands, contact
NetComm TeleMarketing.
6
Distinctive Ring
AT-SDR=n, where n=0 to 7, default=0
AT-SDR=0 Any ring detected and reported as "RING"
AT-SDR=1 Single ring detected and reported as "RING1"
AT-SDR=2 Double ring detected and reported as "RING2"
AT-SDR=3 Single and Double ring detected and reported as
"RING1" or "RING2"
AT-SDR=4 Triple ring detected and reported as "RING3"
AT-SDR=5 Single and Triple ring detected and reported as
"RING1" or "RING3"
AT-SDR=6 Double and Triple ring detected and reported as
"RING2" or "RING3"
AT-SDR=7 Any ring detected and reported as "RING1" or
"RING2" or "RING3"
☞ Use AT-SDR=4 for Telstra's Duet service.
Do not set Auto Answer below 2 when Distinctive Ring is enabled.
Response Codes
Num Verbal Description
0 OK Command accepted
1 CONNECT Connection established
2 RING Incoming call detected
3 NO CARRIER Carrier not detected
4 ERROR Command error
6 NO DIALTONE Dial tone not detected, check phone
connection
7 BUSY The number dialled is busy
8 NO ANSWER Silence not detected
13 RINGING The number dialled is ringing
20 CONNECT/REL Connection established error corrected
22 CONNECT 1200/REL Connected at 1200 bps error corrected
23 CONNECT 2400/REL Connected at 2400 bps error corrected
24 CONNECT 4800/REL Connected at 4800 bps error corrected
28 CONNECT 7200/REL Connected at 7200 bps error corrected
25 CONNECT 9600/REL Connected at 9600 bps error corrected
26 CONNECT 12000/REL Connected at 12000 bps error corrected
27 CONNECT 14400/REL Connected at 14400 bps error corrected
43 CONNECT 16800/REL Connected at 16800 bps error corrected
44 CONNECT 19200/REL Connected at 19200 bps error corrected
45 CONNECT 21600/REL Connected at 21600 bps error corrected
46 CONNECT 24000/REL Connected at 24000 bps error corrected
47 CONNECT 26400/REL Connected at 26400 bps error corrected
48 CONNECT 28800/REL Connected at 28800 bps error corrected
96 CONNECT 31200/REL Connected at 31200 bps error corrected
98 CONNECT 33600/REL Connected at 33600 bps error corrected
49 CONNECT 38400/REL Connected at 38400 bps error corrected
50 CONNECT 57600/REl Connected at 57600 bps error corrected
70 CONNECT 76800/REL Connected at 76800 bps error corrected
71 CONNECT 96000/REL Connected at 96000 bps error corrected
72 CONNECT 115200/REL Connected at 115200 bps error corrected
5 CONNECT 1200 Connected at 1200 bps
10 CONNECT 2400 Connected at 2400 bps
11 CONNECT 4800 Connected at 4800 bps
32 CONNECT 7200 Connected at 7200 bps
12 CONNECT 9600 Connected at 9600 bps
30 CONNECT 12000 Connected at 12000 bps
31 CONNECT 14400 Connected at 14400 bps
33 CONNECT 16800 Connected at 16800 bps
34 CONNECT 19200 Connected at 19200 bps
35 CONNECT 21600 Connected at 21600 bps
36 CONNECT 24000 Connected at 24000 bps
37 CONNECT 26400 Connected at 26400 bps
38 CONNECT 28800 Connected at 28800 bps
95 CONNECT 31200 Connected at 31200 bps
97 CONNECT 33600 Connected at 33600 bps
39 CONNECT 38400 Connected at 38400 bps
40 CONNECT 57600 Connected at 57600 bps
60 CONNECT 76800 Connected at 76800 bps
61 CONNECT 96000 Connected at 96000 bps
62 CONNECT 115200 Connected at 115200 bps
63 CONNECT 230400 Connected at 230400 bps
7
© 1996 NetComm Limited
YPT125-3B
8
Loading...