OPTION 1
Volume controls mounted on rear of amplier. Order this option if expanding the amplier with the RABX2 or RAMX2 input mixers. Master volume can be preset
with the rear volume controls.
OPTION 2
Volume controls mounted on front panel. Order this option for devices such as TV’s, Background Music, Radio etc that require volume controls. Two modes of
operation via jumper. Independent two zone volume controls or two mixed input channel volume controls to one zone.
FCC INTERFERENCE STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used in accordance to the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by switching the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Consult the dealer or an experienced radio or TV technician for help.
RAAX2 - OPTION 1 RAAX2 - OPTION 2
OCTASOUND - RAAX2 - 2 CHANNEL REMOTE AUDIO AMPLIFIER
OWNERS MANUAL
POWER SUPPLY OPTIONS
Power supply is sold separately. Choose your power supply based on operation requirements of the RAAX2 Amplier.
PS-RAAX2-15-1600 15Vdc @ 1.6 amps. Maximum output power of RAAX2 = 12 Watts @ 8 Ohms . Ideal for low audio volume operation requirements.
PS-RAAX2-24-5000 24Vdc @ 5 amps. Maximum output power of the RAAX2 = 30 Watts RMS @ 8 Ohms. Ideal for high audio volume operation requirements.
POWER (Black 2 pin terminal, euro-style)
Power to the RAAX2 is provided via a 1.6 amp 15 Volt power pack. Insert the black male connector on the end of the power
supply into the +PWR- power connector on the rear of the RAAX2. Larger power supplies are available for higher power
operation. 15 Vdc to 24 Vdc - 5 amps maximum FCC compliant power supply.
AUX POWER: (Green 2 pin terminal)
15 Vdc auxiliary power is provided via the AUX OUT PWR terminal. This can be used to power an external RAMX2 or RABX2 input
mixer.
INPUTS: (Green 5 pin terminal)
Wire input signal to + - and GND terminals for balanced inputs. Use + and GND for unbalanced in.
OUTPUTS: (2 x Orange 2 pin terminals, euro-style)
CH1 and CH2 can be wired to 8 or 4 ohm speakers. Each channel can support two 8 Ohms speakers wired in parallel.
MUTE: (Green 2 pin terminal)
Wire to normally open switch. Contact closure mutes both outputs
MODE OF OPERATION: (Onboard jumper)
Jumper on = mixer mode. No Jumper = stereo mode
Stereo/Zone Mode: CH1 input to CH1 output, and CH2 input to CH2 output.
Mixer Mode (jumper installed): CH1 and CH2 inputs to both CH1 and CH2 outputs.
RAAX2 - 2 CHANNEL POWER AMPLIFIER WIRING INSTRUCTIONS
RAAX2 - 2 CHANNEL POWER AMPLIFIER SAMPLE APPLICATIONS
PWR GND PWR GND CH1+CH1- CH2 - CH2 +
Connectors Supplied
With RAMX2 and RABX2
MIXERS
WIRING TO RAMX2 OR RABX2 INPUT MIXERS
CH1+CH1
AUX
POWER OUT
2 PIN GREEN TERMINAL
5 PIN GREEN TERMINAL
TO RAAX2
FROM RAMX2 OR RABX2
OUTPUT CONNECTOR
RAAX2 REAR VIEW
OUT CH1
OUT CH2
POWER IN
CH1 CH2
SIGNAL IN
AUX
POWER
MUTE
TREBLE CH1
TREBLE CH2
BASS CH1
BASS CH2
VOLUME CH1
(Not installed option 02)
VOLUME CH2
(Not installed option 02)
STEREO / MIXER MODE
JUMPER
RAAX2 WITH RABX2 IN SMLV-2 CASE
Bluetooth and aux input amplifer - 2 x 50 Watts
5.75”
6 x RAAX2 INSTALLED INTO RM600 - Rack Mount Chasis 3RU
Multi Room Applications.
SPA 1 POOL BAR 1SPA 2 PATIO CABANATIKI BAR
Loading...