Calibration Light Source
CAL-2000
Installation and Operation Manual
Document Number 000-10000-010-02-1209
Offices: Ocean Optics, Inc. World Headquarters
830 Douglas Ave., Dunedin, FL, USA 34698
Phone 727.733.2447
Fax 727.733.3962
8 a.m.– 8 p.m. (Mon-Thu), 8 a.m.– 6 p.m. (Fri) EST
Ocean Optics Mikropack
Maybachstraße 11, D-73760, Ostfildern, Germany
Phone +49 (0)711 34 16 96-0
Fax +49 (0)711 34 16 96-85
000-00000-000-02-A
E-mail: Info@OceanOptics.com (General sales inquiries)
Info@Mikropack.de (Mikropack sales inquiries)
Orders@OceanOptics.com (Questions about orders)
TechSupport@OceanOptics.com (Technical support)
Protective Eye Wear Must Be Worn When
Using This Instrument Intense Ultraviolet Radiation Present
See Important Safety Notices inside.
Copyright © 2009 Ocean Optics, Inc.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, by any means, electronic, mechanical,
photocopying, recording, or otherwise, without written permission from Ocean Optics, Inc.
This manual is sold as part of an order and subject to the condition that it shall not, by way of trade or otherwise, be lent, re-sold, hired out or otherwise
circulated without the prior consent of Ocean Optics, Inc. in any form of binding or cover other than that in which it is published.
Trademarks
Microsoft, Windows, Windows 95, Windows 98, Windows Me, Windows NT, Windows 2000, Windows XP and Excel are either registered trademarks or
trademarks of Microsoft Corporation.
Limit of Liability
Every effort has been made to make this manual as complete and as accurate as possible, but no warranty or fitness is implied. The information provided is
on an “as is” basis. Ocean Optics, Inc. shall have neither liability nor responsibility to any person or entity with respect to any loss or damages arising from
the information contained in this manual.
C 000-00000-000-02-0604
1. Do not remove or modify any installed safety device on this equipment. Doing so will void
2. Dangerous voltages are present in this device. There are NO user serviceable parts inside.
3. Only allow qualified personnel to service this unit.
4. Do not use the unit if it is damaged in any way. Contact your dealer for repair or replacement
5. Always screw in the fiber optic cables before starting the instrument.
WARNING
Important Safety Notices
your warranty and create an unsafe operating environment.
information.
Protective eyewear must be worn when using this equipment - Intense
ultraviolet radiation present.
Never look directly into the light beam, as this can cause eye damage.
000-10000-010-02-1209 A
Important Safety Notices
B 000-10000-010-02-1209
Table of Contents
About This Manual .............................................................................................................iii
Document Purpose and Intended Audience..............................................................................iii
What’s New in this Document ................................................................................................... iii
Document Summary..................................................................................................................iii
Product-Related Documentation ............................................................................................... iii
Upgrades ............................................................................................................................iii
Chapter 1: Setup ...................................................................................1
Overview.............................................................................................................................1
Unpacking the CAL-2000 .......................................................................................................... 2
Contents ....................................................................................................................................2
Chapter 2: CAL-2000 Specifications ..................................................3
Operating Environment ......................................................................................................3
Spectral Lines.....................................................................................................................5
Appendix A: Bulb Replacement ..........................................................7
Replacing the Bulb .............................................................................................................7
Index ......................................................................................................9
000-10000-010-02-1209 i
Table of Contents
ii 000-10000-010-02-1209
About This Manual
Document Purpose and Intended Audience
This document provides you with an installation section to get your system up and running.
What’s New in this Document
This version of the Calibration Light Source CAL2000 Installation and Operation Manual updates the
logo and contact information..
Document Summary
Chapter Description
Chapter 1: Setup
Chapter 2: CAL-2000 Specifications
Appendix A: Bulb Replacement
Contains a list of package contents and unpacking
instructions.
Contains operating environment specifications, as
well as other physical details of the product.
Provides instructions for changing the bulb.
Product-Related Documentation
You can access documentation for Ocean Optics products by visiting our website at
http://www.oceanoptics.com. Select Technical → Operating Instructions, then choose the appropriate
document from the available drop-down lists. Or, use the
of the web page.
You can also access operating instructions for Ocean Optics products on the
Resources
Engineering-level documentation is located on our website at Technical → Engineering Docs.
CD included with the system.
Search by Model Number field at the bottom
Software and Technical
Upgrades
Occasionally, you may find that you need Ocean Optics to make a change or an upgrade to your system.
To facilitate these changes, you must first contact Customer Support and obtain a Return Merchandise
Authorization (RMA) number. Please contact an Ocean Optics Application Scientist for specific
instructions when returning a product.
000-10000-010-02-1209 iii
About This Manual
iv 000-10000-010-02-1209
Chapter 1
Setup
Overview
The following sections provide instructions on unpacking and setting up your CAL-2000 Calibration
Light Source.
Before using the CAL-2000 for the first time check for transport damage. Be sure to adhere to all
warnings on the unit and in this manual.
000-10000-010-02-1209 1
1: Setup
Unpacking the CAL-2000
► Procedure
1. Unpack your lamp assembly carefully. Although the lamp is rigidly mounted, dropping this
instrument can cause permanent damage.
2. Inspect the outside of the instrument and make sure that there is no damage. Do not use the
instrument if damage is present.
3. Use this instrument in a clean laboratory environment.
Contents
Your CAL-2000 package should contain the following:
CAL-2000
Additionally, you will need a 12 volt DC power supply, such as the Mikropack PS220.
2 000-10000-010-02-1209
Chapter 2
CAL-2000 Specifications
This section provides information on the operating environment, physical controls, and dimensions of the
CAL-2000. It also provides a graph of spectral lines.
Operating Environment
The following table provides information on optimizing the operating environment of your CAL-2000.
Operating Environment The Cal-2000 Unit . . .
Moisture Is designed for operation in dry rooms only.
Ventilation Should be situated so that its location or position does not interfere
with proper ventilation.
Heat Should be situated away from any device that emits excessive heat.
Object and Liquid Entry Should be positioned so that objects do not fall on top of the unit.
Additionally, ensure that no liquids are spilled into the enclosure
through openings.
Power Sources Should be connected to a power supply with the following
specifications:
12 VDC 1000mA analog regulated (e.g. Mikropack PS 220)
000-10000-010-02-1209 3
2: Cal-2000 Specifications
Front of Unit: Fiber optic SMA 905 compatible connector.
LED – Indicates power status of the CAL-2000
Back of Unit: Power Input -12VDC ON/OFF-Switch
Battery Compartment:Use only 9V E-Block Battery VARTA Type 4022 Alkaline
Housing Dimensions: 141 mm x 124 mm x 53 mm
Power LED
SMA Connector
4 000-10000-010-02-1209
Spectral Lines
2: Cal-2000 Specifications
000-10000-010-02-1209 5
2: Cal-2000 Specifications
6 000-10000-010-02-1209
Appendix A
Bulb Replacement
To order replacement bulbs for the CAL-2000, order item number: CAL-2000B
Replacing the Bulb
► Procedure
1. Remove the four screws that secure the curved top of the CAL-2000.
2. Remove the bulb from the CAL-2000 by gently pulling the lamp out of the internal lamp
socket.
3. Insert the new CAL-2000B firmly into the internal lamp socket.
4. Resecure the curved top onto the CAL-2000 with the four mounting screws.
000-10000-010-02-1209 7
A: Bulb Replacement
8 000-10000-010-02-1209
Index
B
bulb replacement, 7
D
dimensions, 4
document
audience, iii
purpose, iii
summary, iii
O
operating environment, 3
P
package contents, 2
product-related documentation, iii
S
setup, 1
specifications, 3
spectral lines, 5
U
unpacking procedure, 2
upgrades, iii
W
what's new, iii
000-10000-010-02-1209 9
Index
10 000-10000-010-02-1209
Loading...