Page 1
USER MANUAL
OMX-3GSDI-SC
3GSDI Extender Over Fiber Optical
812 Kings Highway · Saugerties, NY 12477
Ocean Matrix
www.oceanmatrix.com
Page 2
OMX-3GSDI-SC
3GSDI Extender
The Ocean Matrix OMX-3GSDI-SC extends 3GSDI signal transmission
beyond the standard cable distance limitations and transmits 1080p
3GSDI signal over a singlemode SC fiber optic cable up to 12.43 miles
(20km). Consisting of a transmitter and a receiver, this system supports
SD-SDI, HD-SDI and 3G-SDI signal input.
IR signal transmission allows for remote control of the source at a
secondary location using IR extension cables.
Includes
One transmitter
One receiver
Two 5VDC/2A power adapters
One IR blaster extension cable, connects to transmitter
One IR receiver extension cable, connects to receiver
Specifications
Supported Resolutions SD-SDI 480i@60Hz, 576i@50Hz
SDI Signal Format SD-SDI, HD-SDI, 3GSDI
SDI Rate
SDI Resistance 75Ω
Transmission Range 1080p resolution up to 12.43 miles (20km) over singlemode
IR Remote Control Supports 20-60kHz standard IR remote controls
Power Supply 5VDC/2A
Power Consumption Transmitter 10W, Receiver 10W
Working Temperature 32°F - 140°F (0°C- 60°C)
Dimensions (LxWxH) 6.6 x 3.74 x 0.87 in (168 x 95 x 22mm) TX & RX
Weight Transmitter: 14 oz (400g), Receiver: 14 oz (400g)
Ocean Matrix OMX-3GSDI-SC Page 2
HD-SDI 720p@50/60Hz,1080i@50/60Hz,1080p@24/25/30Hz
3GSDI 1080p@50/60Hz
270Mb/s，1.485Gb/s，2.97Gb/s
Page 3
OMX-3GSDI-SC
Installation Requirements
1. SDI source device such as a video camera, media player,
monitoring equipment or computer.
2. SDI display device such as an SDTV, HDTV, or projector.
3. SDI cables and singlemode SC fiber optic cables.
Installation Safety
1. Identify the receiver and the transmitter in order to make proper
connections during installation.
2. Do not hot plug/swap when in operation.
3. Use 5VDC power supply only.
IR User Guide
1. Plug the IR blaster extension cable into the IR-out port of the Transmitter TX.
2. Plug the the IR receiver extension cable into the IR-IN port of the
Receiver RX.
3. Place the emitter of the IR blaster as close as possible to the IR
receiver of the signal source device.
4. Direct the IR remote controller of the signal source device towards
the IR receiver (connected to the RX of HDMI extender), to remote
control source media playback.
Ocean Matrix OMX-3GSDI-SC Page 3
Page 4
OMX-3GSDI-SC
Transmitter
1
TX Power Input 5VDC
2
TX Reset Button
3
TX IR Blaster Extension Cable Port
Receiver
7 8 9
6
RX Power Input 5VDC
7
RX Reset Button
8
RX IR Extension Cable Port
Rear of Both Units
3 4
4
5
9
RX SDI Signal Output
10
RX Fiber Optic Signal Receive Port
5 1 2
TX SDI Signal Input
TX Fiber Optic Signal Transmit Port
10 6
11
12 13
11
Power Status Indicator
12
Data Transmission Indicator
13
Network Connection Indicator
Ocean Matrix OMX-3GSDI-SC Page 4
Page 5
OMX-3GSDI-SC
Installation Procedures
CONNECTION
Transmission distance up to 12.43 miles (20km) over singlemode SC
fiber optic cable.
HD
Camera
SDI In
TX
UTP Cat5e/6e/7
Cable
IR OUT
Troubleshooting
Display shows “ Waiting for Connection”
Ensure power supply is firmly connected.
Display shows “ Signal Loss”
Check signal input of the TX.
Connect the signal source directly to the display device to
ensure there is a signal output. Change the signal source if
necessary.
Degraded video signal
Check cable lengths between the TX to the switch, the
switch to RX.
RX
SDI Out
IR IN
TV
Ensure the connection between each level is within
required ranges.
Press the RESET button on the TX/RX front panel.
Ensure the fiber optic cables are clean.
Ocean Matrix OMX-3GSDI-SC Page 5
Page 6
SAFETY PRECAUTIONS
1. To prevent fire or shock hazard, do not expose this equipment to high
humidity and/or dust. Do not use in an unprotected outdoor installation
nor any area classified as overly damp or wet.
2. The temperature for installation should be kept between 32°F to 140°F
(0°C to 60°C). Avoid direct sunlight exposure or extreme changes of
temperature over a short period of time.
3. Do not disassemble the unit or place it on an unstable base.
4. Do not drop the unit and avoid heavy impact.
5. This unit should not be permanently installed unless proper ventilation is
provided. Any enclosure openings must not be blocked or covered as they
protect the unit from overheating.
6. Before cleaning, turn off the power and unplug the unit from all connec-
tions. Use a damp cloth. Do not use liquid cleaners nor aerosol cleaners.
7. Do not overload outlets and extension cords as this may result in a risk of
fire or electric shock.
8. Enclosure entry is dangerous. Never push objects of any kind, including
liquids, into this unit through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or electric shock.
9. Do not attempt to open or service this unit yourself as opening or removing
covers may expose you to dangerous voltage and other hazards.
10. There are no user-serviceable parts inside the unit. If the unit requires
service contact your authorized dealer, or an authorized repair service
company.
Ocean Matrix
812 Kings Highway
Saugerties NY 12477
www.oceanmatrix.com
Loading...