Oceanled 001-500596, 001-500598 Installation Manual
OceanLED Marine
Product Support
OceanLED
This installation manual covers the following products:
DMX TOUCH PANEL CONTROLLER
DMX Touch Panel
Controller
DMX WIFI Touch Panel
Controller
All COLOURS Models All COLOURS Models
DMX Touch Panel Controller Kit Includes DMX Wifi Touch Panel Controller Kit Includes
DMX Touch Panel
Controller
DMX WIFI Touch Panel
Controller
Power Cable with
converter
Power Cable with
converter
DMX Output Pigtail DMX Output Pigtail
Micro USB Cable Mini USB Cable
Terminator Kit Terminator Kit
Infared Remote
DMX Controller
INSTALLATION
MANUAL
OceanLED INSTALL / DMX Controller / 073114 / v4.2
2
IMPORTANT: Please read the instructions completely before proceeding with the installation. Failure to
follow the instructions may invalidate your warranty. These instructions supersede any other instructions
if they dier.
Chapter 1 .......................................................................................................................................................................................................4
Overview: Identifying your model and power source, tools and materials necessary for installation,
selecting the mounting site
Chapter 2 ...................................................................................................................................................................................................... 6
Installation of DMX Touch Panel Controller
Chapter 3 ...................................................................................................................................................................................................... 8
Installation of DMX WIFI Touch Panel Controller
Chapter 4 ....................................................................................................................................................................................................12
Finalizing your OceanLED Installation
Chapter 5 .....................................................................................................................................................................................................13
Operation and Troubleshooting
Chapter 6 .....................................................................................................................................................................................................15
Warranty Statement and Notes
PRETEST
Always test the lights prior to installation. Failure to do this may result in additional installation time and
could invalidate the warranty.
GENERAL
OceanLED underwater lights are generally used for illuminating the water around a boat or yacht.
Placement for achieving the best results are described in selecting the right location.
OceanLED INSTALL / DMX Controller / 073114 / v4.2
3
IMPORTANT SAFETY PRECAUTIONS!
! IMPORTANT NOTICE: Attention Installer: This manual contains important information about
the installation, operation and safe use of this product. This information should be given to the owner and/
or operator of this equipment.
! WARNING - Before installing your DMX Controller, read and follow all warning notices and
instructions which are included. Failure to follow safety warnings and instructions can result in
severe injury, death, or property damage.
! WARNING - Before installing your DMX Controller, check local laws for restrictions regarding
the use of colored lights in your area.
! DANGER! Risk of Electrical Shock or Electrocution!
This underwater light must be installed by a licensed or certified electrician in accordance with the
National Electrical Code and all applicable local codes and ordinances. Improper installation will create
an electrical hazard which could result in death or serious injury to swimmers, installers, or others due
to electrical shock, and may also cause damage to property. Always disconnect the power to the light
at the circuit breaker before servicing the light. Failure to do so could result in death or serious injury
to serviceman, swimmers or others due to electrical shock. READ AND FOLLOW ALL INSTRUCTIONS
IN THIS MANUAL.
! WARNING Important Safety Information for OceanLED Lights
! WARNING - Salt is an inherently corrosive material. Metal parts and certain natural and
man-made surfaces are particularly susceptible to corrosion and deterioration when used in
and around salt water. Some OceanLED lights contain combinations of plastic and polymer
products which are impervious to salt water corrosion, however, screws and fasteners used for the
installation must be of a marine grade type stainless steel or equivalent and monitored annually
to ensure the lights remain in service for years to come.
WARNING!
Never Use Solvents! Cleaners, fuel, paint, sealants, and other products that may
contain strong solvents, such as acetone, that attack many plastics greatly reducing their
strength and irreversibly damaging the special lens coatings and cable sheathings.
-
OceanLED INSTALL / DMX Controller / 073114 / v4.2
44
1
CHAPTER
ONE
Chapter 1: Identifying your Model
DMX TOUCH PANEL CONTROLLER
DMX Touch Panel
Controller
DMX WIFI Touch Panel
Controller
001-500596 001-500598
WARNING: UNITS ARE NOT WATER PROOF. YOU MUST MOUNT IN A DRY LOCATION.
• For use with the all COLOURS systems. Available as a fixed or wifi controller.
• Use to change the colour and lighting eects of the above lights and choose between a spectrum of
6 million colours to suit your mood.
• The wifi controller can be easily programmed to create individual colour scenes, which can then be
selected at the touch of a button using your iPhone, iPad, or Android.
• The DMX Wifi Touch Panel Controller can only be utilized when connected to a wifi enabled network
1.1 Tools and Materials
WARNING: NEVER USE POWER TOOLS; HAND TIGHTEN ONLY!
WARNING: OCEANLED RECOMMENDS DRY FITTING ALL PRODUCTS. WHEN INSTALLING,
BESURE THAT THE CONTROLLER FITS THE AREA AND SECURES TO THE MOUNTING
LOCATION USING THE APPROPRIATE HARDWARE BEFORE INSTALLING.
• Drill & Drill Bits.
• Screw Driver, Phillips #2
• Wire Strippers.
• Tape measure and Ruler or Straight Edge.
• Marking Utensil (Pencil, Sharpie Magic Marker, etc)
OceanLED INSTALL / DMX Controller / 073114 / v4.2
5
OceanLED INSTALL / DMX Controller / 073114 / v4.2
1.2 Finding The Mounting Location
WARNING: UNITS ARE NOT WATER PROOF. YOU MUST MOUNT IN A DRY LOCATION.
Considerations
Design -
• The unit needs to be mounted in a dry location
• Ensure that the ambient temperature where the unit is mounted cannot exceed 45 degrees C - Note
that engine rooms can easily exceed this.
• The chosen location requires access to mains power, space for the routing of the DMX cable to the
driver boxes, and also an Ethernet connection to a wifi router / LAN wifi for the Wifi controller if the
wifi function is required.
Installation -
• Test units before installation.
• When switching system on for the first time, take into consideration water clarity, ambient light etc as
first time impressions can be marred by poor conditions.
• Test units after installation.
66
2
CHAPTER
TWO
OceanLED INSTALL / DMX Controller / 073114 / v4.2
Chapter 2: I
nstalling the DMX Touch Panel Controller
2.1 Connect the wires
1.
Connect the DMX output pigtail cable to the green connector (LEDs, Dimmers, Fixtures..)
(Brown+Brown/White=ground, Orange=DMX-, Orange/White=DMX+)
2.
POWER: Connect the AC/DC adapter. (Black/White Stripe=Positive, Black=Ground)
2.2 Mount the interface in a dry location
3.
Plug the green connector block into the rear of the DMX Touch Panel Controller.
4.
Mount the back plate of the interface on the preferred mounting location. (in a dry place) 86mm
X 86mm X 10mm
5.
Close the unit by clipping the front panel onto the back plate.
7
OceanLED INSTALL / DMX Controller / 073114 / v4.2
2.3 Specifications DMX Touch Panel Controller
Factory Default Programming for DMX Touch Panel Controller (001-500596)
Scene Function
1 Red
2 Green
3 Blue
4 Super White
5 Colour Cycle
Compatible with any DMX fixture or DMX LED driver
Ready to use (pre-loaded with 8 scenes & 42 RGB fixtures)
3 touch sensitive buttons (on/o/mode, previous, next
32-bit ARM technology
Up to 24 dynamic or static scenes
Live setting of the intensity and color of a scene
Programmable through the included USB cable & control software
Windows XP/VISTA/7 32/64 bits & USB 2.0* (MAC OSx available soon)
Easy Stand Alone, ESA2 mac/pc
Environment IP20, Temp 0˚C to 50˚C
Certifications
EC, EMC, ROHS, ETL, UL (some in progress)
88
3
CHAPTER
THREE
Chapter 3: I
nstalling the DMX WIFI Touch Panel Controller
3.1 Connect the wires
1.
Connect the DMX Output Pigtail cable to the green connector (LEDs, Dimmers, Fixtures..)
(Brown+Brown/White=ground, Orange=DMX-, Orange/White=DMX+)
2.
POWER: Connect the AC/DC adapter. (Black/White Stripe=Positive, Black=Ground)
3.
Ports 1,2,3,and 4 : If your application needs to have some external contact closures, make the
contacts between the ground and the ports.
3.2 Mount the interface in a dry location
4.
Plug the green connector block
into the rear of the DMX WIFI
Touch Panel Controller.
5. For Wifi plug the local ethernet
cable into the rear of the DMX wifi
touch panel controller.
6.
Mount the back plate of the
interface on the preferred
mounting location. (in a dry
place) 168 x 128 x 11.5mm.
7.
Close the unit by clipping the
front panel onto the back plate.
OceanLED INSTALL / DMX Controller / 073114 / v4.2
Loading...