Page 1
-
o
Océ
ColorWave
®
550
Advance
Your Printing
User manual
Safety information
Page 2
Copyright
© 2012, Océ
All rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted
in any form or by any means without written permission from Océ.
Océ makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.
Furthermore, Océ reserves the right to revise this publication and to make changes from
time to time in the content hereof without obligation to notify any person of such revision
or changes.
Edition: 2012-04
Page 3
Contents
Chapter 1
Instructions for safe use.....................................................................................5
Instructions for safe use............................................................................6
Chapter 2
Regulation notices............................................................................................13
Regulation notices....................................................................................14
Chapter 3
General information.........................................................................................19
General information (All countries)........................................................20
Chapter 4
Miscellaneous....................................................................................................21
Addresses of local Océ organisations ...................................................22
3
Contents
Page 4
4
Contents
Page 5
Chapter 1
Instructions for safe use
Page 6
Instructions for safe use
Introduction
All the products have been tested in accordance with the strictest international safety
standards. Please read the following sections before you connect the machine to the
power supply. These sections contain important information with regard to the user
safety and the prevention of equipment problems. Make sure that you observe the safety
rules hereinafter. This helps to assure that you can work with the product safely. Make
sure that you observe all the precautions mentioned below.
Note:
Depending on the context, the terms: system, machine and equipment all will be used
to designate the product for which the user documentation is applicable.
Note:
Some parts of the contents of this section may not be applicable to your product.
Note:
Please refer to the corresponding Safety Data Sheets for specific safety information. You
can download the Safety Data Sheets from the support site of your product at
http://global.oce.com/support/.
Warning and precaution symbols
Warning:
Ignoring this warning could cause serious injury or even death.
Caution:
Ignoring this warning could cause injury or damage to property.
Note:
Indicates additional important information.
The following indicators are used in the machine to warn the user of possible safety risks:
Chapter 1 - Instructions for safe use6
Instructions for safe use
Page 7
#
Ignoring this caution could cause injury to skin; see also
the section "Actions in response to troubles".
Caution
Hot
Whenever this label is affixed to parts of the machine that
are accessible to the user, a remark can be found in the user
documentation, explaining the potential hazard for which
the user is warned or cautioned. The user is urged to consult
the user documentation in order to understand the safety
risk and learn how to avoid damage or injury.
Warning
Disassemble and modification
Warning
•
Do not remove covers and panels which are fixed to the machine. Some machines
have a high-voltage component or a laser beam source inside that could cause an
electrical shock or blindness.
•
Do not modify this machine, because this could cause a fire, electrical shock or
breakdown. If the machine contains a laser, the laser beam source could cause blindness.
Caution
•
Do not carry out maintenance activities for other components and maintenance materials than the components and materials that are mentioned in the user manual.
•
Do not place any liquids on the machine.
•
Do not open any door while the machine starts up or runs, unless the operator panel
displays a message that asks you to open one or more doors.
•
Use maintenance materials or other materials for their intended purpose only.
•
To avoid any risk, only properly qualified and trained service technicians are allowed
to modify the machine.
•
Do not bridge any mechanical or electrical circuit breakers.
Note
•
Keep maintenance materials away from children.
Power cord
Warning
•
Do not scratch, abrade, heat, twist, bend, place a heavy object on or cause any other
damage to the power cord. The use of a damaged power cord (exposed core wire,
broken wire, for example) could result in a fire or breakdown. If you find any of these
conditions, immediately turn OFF the power switch and unplug the power cord from
the power outlet. Then call your authorized service representative.
•
Do not use an extension lead to connect the machine.
•
Do not use any power cable other than the one provided. Never use the power cable
with any other electrical device.
Chapter 1 - Instructions for safe use 7
Instructions for safe use
Page 8
Power source
Warning
•
Put the power plug directly into a wall socket that has the same configuration as the
plug. The use of an adapter leads can result in an inadequate power supply. If a
proper wall outlet is not available, ask a qualified electrician to carry out the installation.
•
Do not connect the machine to a mains voltage that differs from the value as stated
on the power marking label.
•
Do not use a multiple outlet adapter or an extension lead. Contact your authorized
service representative if an extension lead is required.
Caution
•
Consult your authorized service representative before you connect other equipment
to the same wall outlet.
Power plug
Warning
•
For machines that are connected via a wall socket: Place the machine close to a wall
socket that is easily accessible. The power plug is intended to serve as a disconnect
device.
Grounding
Warning
•
Connect the power cord to an electrical outlet (wall socket) that is equipped with a
grounding terminal.
•
This equipment has not been designed for connection to an IT power system. An IT
power system is a voltage network in which the neutral wire is not connected to ground.
•
In particular for Finland (FI), Norway (NO) and Sweden (SE), according to National
Deviations to EN/IEC 60950-1.
#
Laite on liitetävä suojamaadoituskoskettimilla varustettuun pistorasiaanFI
Apparatet må tilkoples jordet stikkontaktNO
Apperaten skall anslutas till jordat uttagSE
Chapter 1 - Instructions for safe use8
Instructions for safe use
Page 9
[3] Figure: 1. The power connection at the back of the printer.
Installation
Warning
•
Make sure that the machine is placed on a level, horizontal surface of sufficient strength.
•
Do not place this machine on an unstable or tilted surface.
•
Do not place this machine in a location that is subject to lots of vibrations and shocks.
•
Do not use flammable sprays, liquids or gases near this product, because this could
cause a fire.
•
Make sure that the stabilizing studs are placed correctly after installing or moving the
machine.
#
Pull out the left 'Foot' [1] until it touches the
ground and locks [2]. You should hear a click as
it locks.
Repeat this procedure on the right hand side of
the Océ ColorWave 550.
Note:
If you do not hear a click, place your foot
on the foot of the printer [1] and at the
same time push gently against the printer
until you hear the click.
•
Use empty drawers to check whether it is possible to open two drawers. If this is possible, call Service.
Ventilation
Caution
•
The machine can produce odors of exhaust air when you:
– use this machine in a poorly ventilated room for a long time
Chapter 1 - Instructions for safe use 9
Instructions for safe use
Page 10
– produce large amounts of copies or prints
Therefore, make sure that you ventilate this room well.
•
Do not block the ventilation openings of the machine.
•
Do not place the machine in rooms which are too small and insufficiently ventilated.
See the Product Safety Data Sheet of the machine for the ventilation requirements.
•
Be sure to allow a clearance of 65 mm (2.6 in.) or more at the back of this machine
for the ventilation duct.
Actions in response to troubles
Warning
•
When a piece of metal, water or any other similar foreign matter gets inside the machine, immediately turn OFF the power switch and unplug the power cord from the
power outlet. Then call your authorized service representative.
•
Immediately stop using the machine if the machine becomes excessively hot, emits
smoke, or produces unusual odors or noises. Immediately turn OFF the power switch
and unplug the power cord from the power outlet. Then call your authorized service
representative.
Caution
•
Stop using the machine if the machine was dropped or a cover was damaged. Immediately turn OFF the power switch and unplug the power cord from the power outlet.
Then call your authorized service representative.
•
Some areas inside the machine become hot. Do not touch the locations that are labeled
with the "Caution Hot" symbol . Touching these areas could cause burns.
•
LCD display. Do not rub, press or touch the display surface with hard material, because
the polarizer at the surface can be easily scratched. The LCD module consists of glass.
Therefore, the LCD module can damage when you drop, pinch strongly or punch
the module. When glass breaks, be careful that you do not get injured by glass pieces.
Call Customer Service.
Consumables, supplies and maintenance materials
Warning
•
Do not leave contaminated parts or parts containing toner or ink within reach of
children.
Caution
•
Always use the materials which the manufacturer recommended and which are developed for this machine. Materials not approved by the manufacturer may result in
faults in your machine.
Moving the machine
Caution
Chapter 1 - Instructions for safe use10
Instructions for safe use
Page 11
•
Make sure that you disconnect the power cord and other cables before you move the
machine.
•
Make sure that you check the documentation for the space requirements before you
move the machine.
•
Unlock the stabilizing studs before moving the machine.
General use
Caution
•
Unplug the machine when you will not use the machine for a long period of time.
•
To prevent overbalance of the machine, only one drawer should be opened at the same
time.
Chapter 1 - Instructions for safe use 11
Instructions for safe use
Page 12
Chapter 1 - Instructions for safe use12
Instructions for safe use
Page 13
Chapter 2
Regulation notices
Page 14
Regulation notices
Introduction
This section describes the regulation notices.
Radio Interference suppression (all countries except USA)
Warning: This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate measures.
FCC approval (USA only)
Note: This system has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the system is operated in a
commercial environment. This system generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
ICES-003 Interference-causing equipment (Canada only)
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
VCCI (Japan only)
Class A ITE
This is a Class A product based on the standard of the VCCI Council. If this equipment
is used in a domestic environment, radio interference may occur. In such cases, the user
may be required to take corrective action.
Battery labeling (EU only)
This product contains (a) Button Cell(s). It (They) is (are) located in (a) printed circuit
board(s) that is (are) essential for the continuous error-free functioning of the product.
The button cell(s) should be removed only by skilled service technicians who are acquainted with the removal instructions provided by Océ
Chapter 2 - Regulation notices14
Regulation notices
Page 15
Button cell specification#
Containing the following substances (if applicable)
Button cell capacity
Button cell location
Li/MnO2220mAhLocated in PowerM(+) Controller, only accessible by service
technician.
Li/MnO2220mAhLocated in the optional PC if the
system includes a scanner
Caution: Océ does not accept any liability for any damage or consequences if the batteries
are removed by persons other than Océ service personnel.
End of Life; WEEE (EU only)
The symbol "the crossed-out wheeled bin" indicates that at end-of-life of the equipment
separate collection is required in the EU Member States. The black bar specifies that the
appliance is put on the market after August 13, 2005. Reference: Directive 2002/96/EC.
Contact your local Océ organization for more information.
RoHS (China only)
The Environmental Protection Use Period (EPUP) applicable for the printing system
designated for deliveries to the People's Republic of China is 20 years. This EPUP, which
does not include consumables or expendables, does not affect any warranty that is provided
for the system and may not be construed or interpreted as a separate guarantee for the
printing system.
ENERGY STAR® (All countries)
Océ has joined the ENERGY STAR® Program of the United States Environmental
Protection Agency (EPA). The purpose of the ENERGY STAR® Program is to promote
the manufacturing and marketing of energy-efficient equipment, thereby potentially re-
Chapter 2 - Regulation notices 15
Regulation notices
Page 16
ducing combustion-related pollution. Using the energy management features outlined
below prevents unnecessary power consumption, which helps to prevent air pollution
from electricity generating plants and saves money on your utility bills. As an ENERGY
STAR® Partner, Océ has determined that Océ ColorWave 550 meets the ENERGY
STAR® criteria for energy efficiency laid down in the ENERGY STAR ® Program Requirements for Imaging Equipment (Version 1.2)
Energy consumption (All countries)
In order to limit energy consumption during times of non-use the Océ ColorWave 550
has a Sleep mode during which the power level is reduced. The value for the Sleep mode
is listed in the Product Safety Data Sheet.
Power modes and delay times
The energy consumption and efficiency are influenced both by the product technology
and by the settings chosen by the user, especially the delay times that are selected to enter
reduced power states. The following delay times have been pre-set.
Power modes and delay times#
Default delay time (minutes)Operational mode
1 minute (range 1 - 60 minutes)Low power
30 minutes (range 15 - 240 minutes)Sleep
The modes above are automatically entered after the Default Delay Time has elapsed;
counting from the moment the last print has been produced. These settings are recommended and for most users ensure both ease of use and low energy consumption. Between
brackets are the minimum and maximum values. The Delay Times can be changed.
Shorter delay times will reduce energy consumption even further, but may cause longer
recovery times. In some cases longer delay times may prove to be more convenient, but
it should be noted that this may cause an increase in energy consumption. Therefore,
from an energy preservation point-of-view, longer delay times are not recommended.
Standby power (Federal Energy Management Program) (all countries)
This product meets the following criteria for the United States Federal Energy Management
Program (FEMP):
•
In Standby mode, this product consumes less than 1 W. After shutting down all systems
properly, Standby mode as defined by FEMP is reached by setting the main switch
to "0".
•
This product has a hard-off switch.
Chapter 2 - Regulation notices16
Regulation notices
Page 17
•
This product meets the ENERGY STAR® Guidelines for energy efficiency.
Recycled paper (All countries)
The use of recycled paper benefits the environment. The Océ ColorWave 550 is designed
to use recycled paper, which complies with the requirements of EN12281:2002. Product
literature on recommended types of recycled copier paper can be obtained from Océ.
Chapter 2 - Regulation notices 17
Regulation notices
Page 18
Chapter 2 - Regulation notices18
Regulation notices
Page 19
Chapter 3
General information
Page 20
General information (All countries)
Caution labels and notations (All countries)
•
Do not remove caution labels or caution notations. If a label or notation is soiled,
please clean the label or notation. If you cannot make label or notation legible, or if
the label or notation is damaged, please contact your service representative.
•
You can find the power-marking label behind the cover of the mains entrance.
Spiral cleaner
I
If a connection to a mains voltage that is different than the rating on the power-marking
label is required, contact Customer Service.
Space requirements and operation precautions (All countries)
•
Please refer to the corresponding Safety Data Sheets for the specific safety information,
including the dimensions of the product, the recommended room volume and ventilation rate. You can download the Safety Data Sheets from the support site of your
product at http://global.oce.com/support/
Operating environment (All countries)
The environmental requirements for correct operation of the machine are as follows:
•
Operating temperature (T): 15°C (59°F) to 35°C (95°F)
•
Relative Humidity (RH): 20% to 80%
Chapter 3 - General information20
General information (All countries)
Page 21
Chapter 4
Miscellaneous
Page 22
Addresses of local Océ organisations
#
Océ-Österreich GmbH
Postfach 95
1233 Vienna
Wienerbergstrasse 11
Vienna Twin Tower
1100 Vienna
Austria
http://www.oce.at/
Océ-Australia Ltd.
P.O. Box 363
Ferntree Gully MDC
Vic 3165
Australia
http://www.oce.com.au/
Océ-Brasil Comércio e Indústria Ltda.
Av. das Nações Unidas, 11.857
Brooklin Novo
São Paulo-SP 04578-000
Brazil
http://www.oce-brasil.com.br/
Océ-Belgium N.V./S.A.
J. Bordetlaan 32
1140 Brussel
Belgium
http://www.oce.be/
Océ Office Equipment (Shanghai)
First Shanghai Center, Phase II, Building
4,
Lane 180, Zhangheng Road
Pudong District
Shanghai 201204, P.R.
China
http://www.oce.com.cn/
Océ-Canada Inc.
4711 Yonge Street, Suite 1100
Toronto, Ontario M2N 6K8
Canada
http://www.oce.ca/
Océ-Danmark a/s
Vallensbækvej 45
2605 Brøndby
Denmark
http://www.oce.dk/
Océ-Czech Republic ltd.
Babická 2329/2
149 00 Praha 4
Czech Republic
http://www.oce.cz/
Océ-France S.A.
32, Avenue du Pavé Neuf
93882 Noisy-le-grand, Cedex
France
http://www.oce.fr/
Océ Finland OY
Niittyrinne 7
02270 Espoo
Finland
http://www.oce.fi/
Chapter 4 - Miscellaneous22
Addresses of local Océ organisations
Page 23
Océ-Hong Kong and China head office
Room 3711-18 Tower 1
Millennium City 1
388 Kwun Tong Road
Kwun Tong
Kowloon
Hong Kong
http://www.oce.com.hk/
Océ-Deutschland GmbH
Solinger Straße 5-7
45481 Mülheim/Ruhr
Germany
http://www.oce.de/
Océ-Ireland Ltd.
3006 Lake Drive
Citywest Business Campus
Saggart
Co. Dublin
Ireland
http://www.oce.ie/
Océ-Hungaria Kft.
H-1241 Budapest
Pf.: 237
Hungary
http://www.oce.hu/
Océ Japan Corporation
1-28-1, Oi
Shinagawa-ku
Tokyo 140-0014
Japan
http://www.ocejapan.co.jp/
Océ-Italia S.p.A.
Strada Padana Superiore 2/B
20063 Cernusco sul Naviglio (MI)
Italy
http://www.oce.it/
Océ Malaysia Sdn. Bhd.
#3.01, Level 3, Wisma Academy
Lot 4A, Jalan 19/1
46300 Petalig Jaya
Selangor Darul Ehsan
Malaysia
http://www.ocemal.com.my/
Océ-Belgium S.A.
Rue Astrid 2/A
1143 Luxembourg
http://www.oce.lu/
Océ-Norge A.S.
Postboks 4434 Nydalen
Gjerdrums vei 8
0403 Oslo
Norway
http://www.oce.no/
Océ-Mexico S.A. de C.V.
Prolongación Reforma 1236,
4to Piso
Col. Santa Fé, Del. Cuajimalpa
C.P. 05348
México, D.F.
Mexico
http://www.oceusa.com/
Chapter 4 - Miscellaneous 23
Addresses of local Océ organisations
Page 24
Océ-Portugal Equipamentos Gráficos S.A.
Av. José Gomes Ferreira, 11 Piso 2 - Miraflores
1497-139 Algés
Portugal
http://www.oce.pt/
Océ-Poland Ltd. Sp.z o.o.
ul. Bitwy Warszawskiej 1920 r. nr. 7
02-366 Warszawa
Poland
http://www.oce.com.pl/
Océ Singapore Pte Ltd.
21 Ubi Road 1
#05-01 Brilliant Building
Singapore 408724
Océ-Svenska AB
Sollentunavägen 84
191 27 Sollentuna
Sweden
http://www.oce.se/
Océ España SA
Business Park Mas Blau
Osona, 2 08820 El Prat de Llobregat
Barcelona
Spain
http://www.oce.es/
Océ (Thailand) Ltd.
B.B. Building 16/Floor
54 Asoke Road
Sukhumvit 21
Bangkok 10110
Thailand
Océ-Schweiz AG
Sägereistrasse 10
CH8152 Glattbrugg
Switzerland
http://www.oce.ch/
Océ (UK) Limited
Océ House
Chatham Way
Brentwood, Essex CM14 4DZ
United Kingdom
http://www.oce.co.uk/
Océ-Nederland B.V.
P.O.Box 800
5201 AV 's-Hertogenbosch
The Netherlands
http://www.oce.nl/
Océ North America Inc.
100 Oakview Drive
Trumbull, CT 06611
USA
http://www.oceusa.com/
Note:
The web site http://www.oce.com gives the current addresses of the local Océ organisations and distributors.
Chapter 4 - Miscellaneous24
Addresses of local Océ organisations
Page 25
Note:
The addresses of local Océ organisations for information about the Wide Format
Printing Systems and the Production Printing Systems can be different from the addresses
above. Refer to the web site http://www.oce.com for the addresses you need.
Chapter 4 - Miscellaneous 25
Addresses of local Océ organisations
Page 26
+2
Page 27
+2
Page 28
-
Beyond the Ordinary
o
Printing for
Professionals
Creating global leadership in printing
Canon and Océ have joined forces to create the global
leader in the printing industry. Our customers can choose
from one of the industry's broadest range of products
backed by best-in-class service and support organizations.
Look to the new Canon-Océ combination for:
•
Enterprise printing in the office and corporate
printroom
•
Large format printing of technical documentation,
signage, and display graphics
•
Production printing for marketing service bureaus and
graphic arts
•
Business Services for document process outsourcing
For more information visit us at:
www.oce.com
© 2012Océ. Illustrations and specifications do not necessarily apply to
products and services offered in each local market. Technical
specifications are subject to change without prior notice. Trademarks
mentioned in this document are the property of their respective owners.
2012-04
US
Loading...