Occipital Structure Core Quick Start Manual

QUICK START GUIDE

Get Started: structure.io/getstarted

CORE

Connect to a computer with USB-C using
the USB-C to USB-A adapter provided.

Note: This icon means the male USB-C
end of the adapter should be plugged
into a computer. It will not work if plugged
into Structure Core.

Connecting to Structure Core

Connecting Structure Core with USB-A

1

2

a

Connecting Structure Core with USB-C

2

b

Connect to a computer with
USB-A using the USB-A to
USB-C cable provided.

Note: Do not plug in the
USB-C to USB-A adapter
into Structure Core.

Using the provided USB-A to USB-C cable,
plug the USB-C end into the USB-C connector
on Structure Core.

Status LED

Structure Core at a Glance

Troubleshooting

For additional information about status LED notification, visit: support.structure.io

Laser Dot Projector

Ultra-wide Vision
Camera

Status LED

Maximum output of laser radiation: < 0.68mW

(Using maximum accessible emission definition, IEC 60825-1:2014 section 3.58)

Emitted wavelength: 824 nm

(Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser
Notice No. 50, dated June 24, 2007)

The laser is controlled by software. Running applications that turn
on depth streaming will activate the laser and operate invisible laser
radiation at a safe level.

Caution: Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure. Avoid exposure to the laser if the
glass is cracked and the laser projector is damaged or has been
exposed to high temperatures for an extended period of time.

This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.

Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Important: Changes or modifications to this product not authorized
by Occipital could void the EMC and laser classification compliance
and negate your authority to operate the product. This product has
demonstrated EMC compliance under conditions that included the
use of compliant peripheral devices and shielded cables between
system components. It is important that you use compliant peripheral
devices and shielded cables between system components to reduce
the possibility of causing interference to radios, televisions, and other
electronic devices.

Other Certifications: CAN ICES-3 (B)/NMB-3(B)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.

Class 1 Label location: bottom of product

Occipital, Inc. 1801 13th Street. Suite 202, Boulder, CO 80302, USA

The Structure Core is a Class 1 Laser Product, certified by an
independent test laboratory according to international standard
IEC 60825-1:2014, under normal use conditions.

Structure Core

NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC

1. Make sure the USB-C end of the provided cable is plugged into your Structure
Core first.

3. When setting up your Structure Core mount be sure to follow the mounting
guidelines provided at support.structure.io

2. Make sure to update your Structure Core to the latest firmware. More information
can be found at support.structure.io

(when plugging in your sensor)

Infrared Global
Shutter Camera

Solid Blue = On / Connected

Flashing Magenta = Laser is Blocked

Solid Red = Laser Error

Infrared Global
Shutter Camera

USB-C
Connector