Observint Technologies BLK-IPS102M User Manual

2.0 Megapixel
H.264 Network IP Camera
User Manual

Product: BLK-IPS102M

Please read this manual before using your camera, and always follow the instructions for

safety and proper use. Save this manual for future reference.

BLK-IPS102M_CM

5/27/11

ii

www.digiop.com

WARNING

RISK OF ELECTRIC SHOCK. DO NOT OPEN.

To reduce the risk of electric shock, do not
remove cover (or back). No user serviceable
parts inside. Refer servicing to qualied
service personnel.

CAUTION



Operate this camera only in environments where the temperature or humidity is within the recommended range.
Operation in extreme temperatures or humidity levels may cause electric shock and shorten the life of the product.

LEGAL NOTICE

DIGIOP® products are designed to meet safety and performance standards with the use of specic DIGIOP
authorized accessories. DIGIOP disclaims liability associated with the use of non-DIGIOP authorized accessories.

The recording, transmission, or broadcast of any person’s voice without their consent or a court order is strictly
prohibited by law.

DIGIOP makes no representations concerning the legality of certain product applications such as the making,
transmission, or recording of video and/or audio signals of others without their knowledge and/or consent. We
encourage you to check and comply with all applicable local, state, and federal laws and regulations before
engaging in any form of surveillance or any transmission of radio frequencies.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks
and names or their products. DIGIOP, Inc. disclaims any proprietary interest in trademarks and trade names other
than its own.

Microsof t, Windows, and Interne t Explorer are either registered trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.

No part of this document may be reproduced or distributed in any form or by any means without the express written
permission of DIGIOP, Inc.

© 2011 by DIGIOP, Inc. All Rights Reserved.

3850 Priority Way South Drive, Suite 200, Indianapolis, IN 46240
Sales/Support: 1.877.972.2522

12.0 Megapixel H.264 Network IP Camera User Manual

Table of Contents

SECTION 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SECTION 2 Installation and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.1 What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2.2 Tools you need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2.3 Mount the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2.4 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2.4.1 Audio in/out connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2.4.2 Sensor in (DI) connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.4.3 Alarm out (DO) connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2.4.4 RS-485 device connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

2.4.5 LAN and power connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.5 Install IPAdmin Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

2.6 Congure the camera network settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

2.6.1 Conguring cameras on networks with DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

2.6.2 Conguring cameras on networks without DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

2.7 Setup the camera Basic Conguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

2.8 Aim, focus, and image quality adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

2.9 Speaker/microphone setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

2.10 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

SECTION 3 Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

APPENDIX A Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

A.1 Reboot camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

A.2 Set camera to factory default network settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

A.3 Checking your Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

A.4 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

APPENDIX B Power over Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

B.1 PoE compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

B.2 Power classication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

APPENDIX C Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

2

www.digiop.com

SECTION 1: FEATURES

SECTION 1

Features

The DIGIOP Black BLK-IPS102M is a professional, premium-grade 2 megapixel, CS-mount box camera designed for indoor use. Lens
and mounting bracket are optional. It features:

• Aptina™ 1/3.2” (4:3) CMOS 2.0 megapixel sensor

• Dual streaming mode

• De-interlacing on DSP

• Unicast/multicast support

• Megapixel compression: H.264/MPEG-4, up to 1600 x 1200 pixels

• Video compression: H.264/MPEG-4/MJPEG (dual stream @ D1)

• Audio compression: G.711 (µLaw, aLaw)/PCM

• Video motion detection support

• 2-way mono audio support

• RTSP/HTTP protocol support

• 10/100 Base-T Ethernet support

• RS485 support

• USB 2.0 support (external storage, wireless LAN)

• Micro SD card support

• PoE support

• Built-in video Content Analysis presence, surveillance

• OSD support

BLK-IPS102M camera body

32.0 Megapixel H.264 Network IP Camera User Manual

SECTION 2: INSTALLATION AND SETUP

Reset USB connector

Micro SD
card slot

LAN

connector

9-pin

terminal

block

DC jack
adapter
cable
connector

Back connectors

Reset – For restarting the camera, or resetting the camera to its factory default network settings. Refer to Appendix A,
Troubleshooting, for more information.

USB mini-B connector – For a USB storage device or Wi-Fi networking device

9-pin terminal block – For DI, DO, audio, and serial communication

Power adaptor connector (DC 12V) – For use with the DC jack adapter and the DC12V power adapter (provided).

Micro SD card slot – SD memory card slot for external storage. SD memory card is not included.

LAN connector (Ethernet) – For an RJ-45 LAN cable with 10/100Base-T Ethernet

4

www.digiop.com

SECTION 2: INSTALLATION AND SETUP

SECTION 2

Installation and Setup

2.1 What’s in the box

Your camera includes the following:

• BLK-IPS102M camera

• Cap for protecting the sensor

• DC power adapter with power plugs for dierent powering sources

• DC jack adapter cable

• Adapter for mounting the camera

• 9-pin terminal block

• Hex wrench

• Quick installation guide

• CD mini disk with application software, software manual, and camera manual (this document)

2.2 Tools you need

To install the camera, you will need:

• Phillips #1 or #0 screwdriver

• Mounting bracket

• Compatible lens

• PC with Microsoft

®

Windows® XP SP3 or newer

NOTE

DIGIOP recommends that a manual iris megapixel lens is used with this camera to support its full resolution.

2.3 Mount the camera

1. Determine where the camera will be mounted and record the Media Access Control (MAC) address of the camera. The MAC
address can be found on the label on the bottom of the camera. Record the information in the following table.

Location:

MAC address:

52.0 Megapixel H.264 Network IP Camera User Manual

SECTION 2: INSTALLATION AND SETUP

2. Install the camera mounting bracket using the instructions provided with the bracket.

3. Attach the adapter for mounting the camera to the side with the label or to the opposite side with the screws provided.

Mounting
adapter

4. Remove the protective cap covering the camera CCD.

5. Attach the lens assembly to the camera by screwing it clockwise onto the camera until it is fully seated. The lens may require
a mounting ring adapter to t onto the camera. Loosen the set screw if necessary.

Mounting ring

6

www.digiop.com

SECTION 2: INSTALLATION AND SETUP

6. Tighten the lens set screw with the hex wrench provided.

7. Attach the camera to the mounting bracket. Use the instructions provided with the bracket.

2.4 Connections

Connections to the camera for audio in and out (microphone and speaker), DI sensor, DO alarm, and RS-485 control are made
through the 9-pin terminal block.

9-pin terminal block

Terminal block pin assignments

If the 9-pin terminal block is detached from the camera, plug it into the mating connector on the back of the camera.

2.4.1 Audio in/out connections

The camera includes an interface for a mono audio input (from a microphone) and a mono audio output (to a speaker). The audio
output is a low level signal that requires an amplied speaker (see Specications). The conguration of the audio wiring (Aout, Ain)
is shown in the following diagram.

72.0 Megapixel H.264 Network IP Camera User Manual

SECTION 2: INSTALLATION AND SETUP

Audio in/out wiring schematic

To connect a speaker and/or microphone to the camera:

1. Strip 1/4” of insulation from the microphone and speaker wires and insert them into the terminal block in the pin locations
shown in the terminal block gure above. Note that the common (ground) leads of the microphone and speaker share the
same terminal block pin.

CAUTION



Do not attach a headphone or earphone directly to the camera.

2.4.2 Sensor in (DI) connection

The camera provides one channel for sensor input that can be connected to either a voltage type or relay type sensor. For
voltage type sensors, the camera allows an input voltage range of 0 ~ 24 V DC, with a 1 V DC threshold (see Specications). The
conguration of the sensor input wiring is illustrated in the following schematics.

CAUTION



Do not exceed the maximum input voltage or the relay switching rate. Refer to the specications in this
manual for more information.

8

www.digiop.com

SECTION 2: INSTALLATION AND SETUP

Voltage type sensor wiring schematic

Relay type sensor wiring schematic

To connect a sensor to the camera, strip 1/4” of insulation from the sensor wires and insert them into the terminal block in the DI 1
and C pin locations shown above. The pin marked C in the terminal block is the common (COM) pin.

2.4.3 Alarm out (DO) connection

The camera supports one alarm out connection to relay type device. It provides up to 24 VAC @ 500 mA or 12 V DC @ 1 A. The
conguration of the relay type alarm wiring is illustrated in the diagram below.

CAUTION



Do not exceed the maximum relay rating. Refer to the specications in this manual for more information.