How it Works
Objetivos y Servicios de Valor A adido S L
Loading...
B
Loading...
Loading...
BHS RTA
Users Manual
104 pgs2.77 Mb0

Objetivos y Servicios de Valor A adido S L BHS RTA Users Manual

RTL8676 11N ADSL2+ Wireless Router
User Manual
Contents
1 Introduction ........................................................................................................1
2 Hardware Installation .........................................................................................6
3 Web Configuration .............................................................................................8
3.2.1 Wizard.......................................................................................13
3.2.2 Internet Setup...........................................................................19
3.2.3 Wireless....................................................................................22
3.2.4 Local Network...........................................................................28
3.2.5 Time and Date..........................................................................32
3.2.6 Logout.......................................................................................32
3.3.1 Advanced Wireless...................................................................33
3.3.2 Port Forwarding........................................................................41
3.3.3 DMZ..........................................................................................44
3.3.4 SAMBA.....................................................................................45
3.3.5 3G WAN Configuration.............................................................46
3.3.6 Parental Control........................................................................51
3.3.7 Filtering Options........................................................................54
3.3.8 QoS Configuration....................................................................59
3.3.9 Firewall Settings .......................................................................64
3.3.10 DNS.....................................................................................65
3.3.11 Dynamic DNS......................................................................65
3.3.12 Network Tools......................................................................67
3.3.13 Routing................................................................................78
3.3.14 Schedules............................................................................82
3.3.15 DLNA...................................................................................83
3.3.16 Logout .................................................................................83
i
3.4.1 System Management................................................................84
3.4.2 Firmware Update......................................................................85
3.4.3 Access Controls........................................................................86
3.4.4 Diagnosis..................................................................................89
3.4.5 Log Configuration .....................................................................92
3.4.6 Logout.......................................................................................93
3.5.1 Device Info................................................................................94
3.5.2 Wireless Clients........................................................................96
3.5.3 DHCP Clients............................................................................96
3.5.4 Logs..........................................................................................96
3.5.5 Statistics....................................................................................97
3.5.6 Route Info.................................................................................98
3.5.7 Logout.......................................................................................99
ii
User Manual
1 Introduction
The device supports multiple line modes. With four 10/100 base-T Ethernet interfaces at the user end, the device provides high-speed ADSL broadband connection to the Internet or Intranet for high-end users like net bars and office users. It provides high performance access to the Internet with a downstream rate of 24 Mbps and an upstream rate of 1 Mbps. It supports 3G WAN, 3G backup, and Samba for USB storage. The device supports WLAN access, such as WLAN AP or WLAN device, to the Internet. It complies with specifications of IEEE 802.11, 802.11b/g/n, WEP, WPA, and WPA2 security. The WLAN of the device supports 2T2R.
1.1 Packing List
1 x device 1 x external splitter 1 x power adapter 2 x telephone cables 1 x Ethernet cable
1.2 Safety Precautions
Take the following instructions to prevent the device from risks and damage caused by fire or electric power:
Use the type of power marked in the volume label. Use the power adapter in the product package. Pay attention to the power load of the outlet or prolonged lines. An
overburden power outlet or damaged lines or plugs may cause electric shock or fire accidents. Check the power cords regularly. If you find any damage, replace it at once.
Proper space left for heat dissipation is necessary to avoid damage
caused by overheating to the device. The long and thin holes on the device are designed for heat dissipation to ensure that the device works normally. Do not cover these heat dissipation holes.
1
User Manual
Do not put this device close to a heat source or under a high temperature
occurs. Keep the device away from direct sunshine.
Do not put this device close to an overdamp or watery place. Do not spill
fluid on this device.
Do not connect this device to a PC or electronic product unless instructed
by our customer engineer or your broadband provider. Wrong connection may cause power or fire risk.
Do not place this device on an unstable surface or support.
1.3 LEDs and Interfaces
Front Panel
Figure 1 Front panel
The following table describes the LEDs of the device.
LED Color Status Description
Off Router powered off
Power Red/Green
Ethernet Green
Wifi Green
WPS Red/Green
Blinking 2Hz Red Solid Green Router powered on correctly. On Ethernet connection is available.
Off On Wi-Fi connection is available.
Off Wi-Fi connection is unavailable. Blinking Green Solid Green WPS active Blinking 2Hz Green Solid Red (20 Problems on WPS registration
Failure on power-on self-test
Ethernet connection is unavailable.
Negotiation or traffic on line.
WPS negotiation open
2
User Manual
LED Color Status Description
seconds) Blinking Green Solid Green Up Quick
3G Red/Green
ADSL Green
Internet Red/Green
Blinking Green Solid Red Authentication failed
Off Off Router powered off
Blinking 2Hz No line detected Blinking 4Hz Line training Solid Line up Blinking Green Solid Green PPP/DHCP up Quick Blinking Green Solid Red Authentication failed
Negotiation
Tx/Rx traffic on line
Traffic through broadband interface
PPP/DHCP negotiation
Tx/Rx traffice on line
Rear Panel
Figure 2 Rear panel
The following table describes the interface of the device.
Interface/Button Description
ADSL
RJ-11 interface connecting to a telephone set through a telephone cable
3
User Manual
Eth1/2/3/4
USB Connecting to a 3G data card or other USB storage device
WLAN/WPS
Reset
Power On/Off Push to power on/off the device.
Ethernet RJ-45 interfaces connecting to the Ethernet interfaces of computers or Ethernet devices
Press the button for less than 1 second to enable
WLAN function.
Press the button for more than 10 seconds to enable
WPS function. Reset to the factory defaults. To restore factory defaults, keep the device powered on and push a paper clip into the hole. Press down the button for more than 5 seconds and then release.
Interface connecting to the power adapter. The power adapter output is: 12V DC, 800mA
1.4 System Requirements
A 10 baseT/100BaseT Ethernet card is installed on your PC. A hub or switch (attached to several PCs through one of Ethernet
interfaces on the device)
Operating system: Windows Vista, Windows 7, Windows 98SE, Windows
2000, Windows ME or Windows XP
Internet Explorer V5.0 or higher, Netscape V4.0 or higher, or Firefox 1.5 or
higher
1.5 Features
Various line modes External PPPoE dial-up access Internal PPPoE and PPPoA dial-up access Leased line mode 1483B, 1483R, and MER access Multiple PVCs (eight at most) and these PVCs can be isolated from each
other
4
User Manual
A single PVC with multiple sessions Multiple PVCs with multiple sessions Binding of ports with PVCs
802.1Q and 802.1P protocol DHCP server NAT and NAPT Static route Firmware upgrade: Web, TFTP, FTP Reset to the factory defaults DNS relay Virtual server DMZ Two-level passwords and user names Web user interface Telnet CLI System status display PPP session PAP and CHAP IP filter IP QoS Samba Remote access control Line connection status test Remote management (telnet and HTTP, TR069) Backup and restoration of configuration file Ethernet interface supports crossover detection, auto-correction and
polarity correction
UPnP 3G WAN and 3G Backup Samba for USB storage
5
User Manual
2 Hardware Installation
Step 1 Connect the ADSL port of the device and the Modem port of the
splitter with a telephone cable. Connect the phone to the Phone port of the splitter through a telephone cable. Connect the incoming line to the Line port of the splitter.
The splitter has three ports:
Line: Connect to a wall phone port (RJ-11 jack). Modem: Connect to the DSL port of the device. Phone: Connect to a telephone set.
Step 2 Connect an Eth port of the device to the network card of the PC
through an Ethernet cable (MDI/MDIX).
Note:
Use twisted-pair cables to connect the device to a Hub or switch.
Step 3 Plug one end of the power adapter to the wall outlet and the other end
to the Power port of the device. Connection 1: Figure 3 displays the application diagram for the connection of the device, PC, splitter and telephone sets, when no telephone set is placed before the splitter.
Figure 3 Connection diagram (without telephone sets before the splitter)
6
User Manual
Connection 2: Figure 4 displays the application diagram for the connection of the device, PC, splitter and telephone sets when a telephone set is placed before the splitter. As illustrated in the following figure, the splitter is installed close to the device.
Figure 4 Connection diagram (with a telephone set before the splitter)
Note:
When connection 2 is used, the filter must be installed close to the telephone cable. See Figure 4. Do not use the splitter to replace the filter.
Installing a telephone directly before the splitter may lead to failure of connection between the device and the central office, or failure of Internet access, or slow connection speed. If you really need to add a telephone set before the splitter, you must add a microfilter before a telephone set. Do not connect several telephones before the splitter or connect several telephones with the microfilter.
7
User Manual
3 Web Configuration
This chapter describes how to configure the device by using the Web-based configuration utility.
3.1 Accessing the Device
The following is the detailed description of accesing the device for the first time.
Step 1 Open the Internet Explorer (IE) browser and enter http://192.168.1.1 Step 2 The Welcome page shown in the following figure appears.
.
Step 3 Click Next to configure your user’s account and Wi-Fi network as
shown in the following Connectivity page, or click Advanced
Configuration for more options.
8
User Manual
By default, the user’s name is MAC@acs and password is the MAC. The MAC is the equipment’s MAC Address leaving out the 2 points. Step 4 Selecte Advanced Configuration to login into the equipment with the
user admin and password 1234, or selected Cancel to return to the
Welcome page without saving changes, or select Next to save
selected changes. When the checkbox Additional Services is
selected, it will go to the following figure.
9
User Manual
When Solo Speedy (LAN1, LAN2, LAN3 y WIFI)+ VOIP(LAN4) is selected, the LAN4 port is used as VOIP port for voice service.
Step 5 Select Advanced Configuration to login into the equipment, or select
Cancel to return to the Connectivity page without saving the changes,
or selected Next to save changes and go to the following
WiFi-Configuration page.
10
User Manual
Next, you are going to config you wireless network. You can enable wireless network, hide the SSID, select a channel and security mode, and input a key as instructed by the screen.
Step 6 Select Next to save changes and go to the following figure, or select
Cancel to return to the Additional Services page without saving the
changes, or select Advanced Configuration to login into the
equipment.
11
User Manual
The Login page is shown as below. Choose the username admin, input the password 1234 and click login.
If you log in successfully, the page shown in the following figure appears.
12
User Manual
If the login information is incorrect, click Try Again in the page that pops up to log in again.
3.2 Setup
In the main interface, click Setup tab to enter the Setup menu as shown in the following figure. The submenus are Wizard, Internet Setup, Wireless, Local
Network, Time and Date and Logout.
3.2.1 Wizard
Wizard enables fast and accurate configuration of Internet connection and other
important parameters. The following sections describe configuration parameters. When subscribing to a broadband service, you should be aware of the method, by which you are connected to the Internet. Your physical WAN device can be Ethernet, DSL, or both. Technical information about the properties of your Internet connection is provided by your Internet service provider (ISP). For example, your ISP should inform you whether you are connected to the Internet using a static or dynamic IP address, or the protocol, such as PPPoA or PPPoE, that you use to communicate over the Internet. Step 1 Choose Setup > Wizard. The page shown in the following figure
appears.
13
User Manual
Step 2 Click Setup Wizard. The page shown in the following figure appears.
Step 3 There are four steps to configure the device. Click Next to continue. Step 4 Set the time and date.
14
User Manual
Step 5 Configure the Internet connection. Set the VPI and VCI. If the Protocol is PPPoE or PPPoA, the page shown in the two following figure appears.
15
User Manual
In this page, enter the user name and password as provided by your ISP. If the Protocol is Dynamic IP, the page shown in the following figure appears.
If the Protocol is Bridge, the page shown in the following figure appears.
16
User Manual
If the Protocol is Static IP, the page shown in the following figure appears.
Enter the IP Address, Subnet Mask, Default Gateway and Primary DNS Server. Click Next. The page shown in the following figure appears.
17
User Manual
Step 6 Configure the wireless network. Enter the information and click Next.
18
User Manual
Step 7 Click Apply to save the settings.
Note:
In each step of the Wizard page, you can click Back to review or modify the previous settings. Click Cancel to exit the wizard page.
3.2.2 Internet Setup
Choose Setup > Internet Setup. The page shown in the following figure appears. In this page, you can configure the WAN interface of the device.
19
User Manual
Click Add in “INTERNET SETUP”. The page shown in the following figure appears.
20
User Manual
The following table describes the parameters in this page.
Field
VPI: The virtual path between two points in an ATM
network, and its valid value is from 0 to 255.
PVC Settings
Service Category
Protocol
Encapsulation Mode
Click Apply, the page shown in the following figure appears.
VCI: The virtual channel between two points in an ATM network, ranging from 32 to 65535 (0 to 31 is reserved for local management of ATM traffic). You can select from the drop-down list.
You can select from the drop-down list.
Select the method of encapsulation provided by your ISP. You can select LLC or VCMUX.
Description
21
User Manual
3.2.3 Wireless
This section describes the wireless LAN and basic configuration. A wireless LAN can be as simple as two computers with wireless LAN cards communicating in a pear-to-pear network or as complex as a number of computers with wireless LAN cards communicating through access points which bridge network traffic to wired LAN. Choose Setup > Wireless. The Wireless page shown in the following figure appears.
3.2.3.1 Wireless Basic
In the Wireless page, click Wireless Basic. The page shown in the following figure appears. In this page, you can configure the parameters of wireless LAN clients that may connect to the device.
22
User Manual
The following table describes the parameters in this page.
Field
Enable Wireless Enable MultiAP Isolation
Wireless Network Name (SSID)
Visibility Status You can select Visible or Invisible. Country Select the country from the drop-down list. Control Sideband
Select this to turn Wi-Fi on or off.
Select this to turn MultiAP isolation on and off.
The Wireless Network Name is a unique name that identifies a network. All devices on a network must share the same wireless network name in order to communicate on the network. If you decide to change the wireless network name from the default setting, enter your new wireless network name in this field.
Choose the channel selection mode as Upper or
Lower.
Description
23
User Manual
Field
Wireless Channel
802.11 Mode
Band Width
Click Apply to save the settings.
Select the wireless channel from the pull-down menu. It is different for different country. Select the appropriate 802.11 mode based on the wireless clients in your network. The drop-down menu options are 802.11b, 802.11g, 802.11n, 802.11b/g,
802.11n/g and 802.11b/g/n. Select the appropriate band of 20M, 40M or 20M/40M from the pull-down menu.
Description
3.2.3.2 Wireless Security
In the Wireless page, click Wireless Security. The page shown in the following figure appears. Wireless security is vital to your network to protect the wireless communication among wireless stations, access points and wired network.
Note:
Enable Wireless before configuring the wireless security settings in this page. Refer to 3.2.3.1 Wireless Basic.
When the Security Mode is set as WEP, the following figure appears.
24
User Manual
25
User Manual
The following table describes the parameters of this page.
Field Description
WEP Key Length
Choose WEP Key
WEP Key 1/2/3/4
Click Apply to save the settings. When the Security Mode is set as Auto (WPA or WPA2), WPA2 only or WPA only, the following figure appears.
Choose the WEP key length. You can Choose 64-bit or 128-bit. Choose the index of WEP Key . You can choose Key 1, 2, 3 or 4. The Encryption keys are used to encrypt the data. Both the modem and wireless stations must use the same encryption key for data transmission. The default key 1 is 8wlHK.
26
User Manual
The following table describes the parameters in this page.
Field
Security Mode
Configure the wireless encryption mode. You can choose None, WEP, Auto(WPA or WPA2), WPA 2 Only or WPA Only. Wired equivalent privacy (WEP) encrypts data
Description
27
Loading...
+ 74 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use