Installation Instructions
Model Number 1077-CP
Assembly Components:
- Ceiling enclosure Model 1077-CP assembly – 1 each
- Universal T-Bar Mount – 1 each
- 3/4” Trade Size Cable Clamp – 1 each
- Fire Block Foam – 1 each
- Support wire – 4 each
- Keys for access door lock – 2 each
- Installation Instructions – 1 each
If any of these items are missing, contact your Oberon representative.
Find a flat work surface to assemble the ceiling enclosure, access point and antenna(s) prior to mounting in ceiling.
Step 1 – Place the ceiling enclosure assembly on the work surface with the keyed doorway unlocked. Remove hole knock
outs located on the outside edge of the back box to install conduit connectors. Install one conduit connector if using P.O.E. or
install 2 conduit connectors if bringing in power and Ethernet and power separately (Figure 1).
Page 2
Figure 1
This product is Listed by Underwriters
Laboratories Inc. Representative
samples of this product have been
evaluated by UL and meet applicable
safety standards.
File #E348543
Step 2 – Unlock and open the door. Use the manufacturers T-Bar mount clip to attach the access point to the T-Bar Section
on the mounting plate. An additional mounting plate provided by the manufacturer of the access point may be needed to
attach the access point (Figure 2). Data cable(s) may need to be plugged in to the access point prior to attaching to the
mount. Cisco access points use Cisco AIR-AP-BRACKET-2 for 2600/3600 series access points and AIR-AP-BRACKET1 for 1140/3500 series.
Step 3 – The enclosure is ready to be placed in the ceiling.
Page 3
Figure 2 – Exploded door view.
(877) 867-2312 • www.oberonwireless.com
Rev. A1 05/23/13 Oberon, Inc. •••• 1315 South Allen Street •••• State College, PA 16801 Copyright 2013
Step 4 – Remove the ceiling tile
from the location where the
access point enclosure is to be
placed (if necessary) and
replace with the assembled unit
(ref. Figure 6). Use a minimum
of two separate grid wires to
attach the access point
enclosure to the ceiling. Attach
one end of the wire to the
eyebolts and the other end to a
permanent structure within the
ceiling such as a ceiling joist.
MODEL 1077-CP
Installation Instructions
**** WARNING ****
**IMPORTANT** - This is
an important safety feature
that could prevent human
injury or damage to the
access point should the unit
become dislodged from the
ceiling grid work.
Step 5 – Once the assembly has been installed in the ceiling and secured using grid wire, open the door and run the Ethernet
cable into the enclosure through the conduit nipple located on the side of the access point enclosure and attach to the access
point prior to installing on mounting plate.
Insert foam into the conduit connector and pull the data cable through far enough to allow attachment to the access point (8" -
10"). Tighten cable clamp around foam fire block so that there are no air gaps. Be careful not to over tighten and crush the
Ethernet cable(s).
Page 4
Please thoroughly read the product warning below
before installation to provide for a safe work
environment.
1. Ceiling mounted products should be installed in accordance with National Electric Code paragraphs 300.10 (Electrical
Continuity of Metal Raceways and Enclosures) and 300.11 (Securing and Supporting). Independent support wires or
other means must be used for the installation of this product in the ceiling. Acoustical, suspended, false, drop and
concealed spline ceiling grid work is not designed to support the weight of this product. Oberon’s ceiling mounted
+
products have four support wire tabs on the back box. These tabs shall be used for supporting the product with
independent support wires, wire rope, threaded rod, or other secure support means of adequate gauge and fire
resistance.
2. When closing the enclosure access door, be sure that the cam lock is completely engaged to prevent the access door
from accidentally swinging open.
3. When opening the enclosure door, be sure to support the door to prevent the door from accidentally falling open.
4. This enclosure has a maximum operating ambient of 55º C (131º F), the temperature within the enclosure may not
exceed this temperature, depending on power dissipation within enclosure.
5. A minimum air clearance of 1“ between the housing of the access point and the enclosure side walls must be
maintained for the safe operation of the equipment.
6. This product is intended to be installed by trained personnel.
7. Only Listed ITE products and Listed AC Receptacles shall be installed within the enclosure.
8. This product is to be repaired by personnel trained by the manufacturer or returned to the manufacturer for repair or
replacement.
9. Maximum weight to be installed in the unit is 25 lbs.
10. All knockouts, openings, and holes shall be sealed with a plug constructed of metal, or a non-metal material that
complies with UL 2043 or UL 1479.
11. All unused mounting holes should be sealed with tape or other material that complies with UL 1479.
12. If AC power is used inside the enclosure, connect the ground wire to the green ground screw located near the
knockout in the backbox.
Page 1
Loading...