Oase FILTOCLEAR 3.000, FILTOCLEAR 1.600, FILTOCLEAR 800, FILTOCLEAR 4.000 Warranty, Safety And Operating Instructions

1

Warranty, Safety and
Operating Instructions

Garantie, mode d'emploi
et consignes de sécurité

Garantia, Instructivo
de Seguridad y de
Operaciones

800 – 1.600 – 3.000 – 4.000

FILTOCLEAR

29746/02C

2

Use these instructions to familiarize yourself with the device before
you use it for the first time. It is absolutely essential that you observe
the safety guidelines on the proper and safe use of the device.
For safety reasons, children and young people under 16 years of
age, as well as people who cannot recognize potential hazards or
who are not familiar with these instructions, must not use this device!
Please keep these instructions in a safe place! In the event of a
change of ownership, please pass these instructions on to the
new owner along with the product.

Symbols

The symbols used on the device and in these instructions have
the following meaning:

Caution! Important advice about hazards!
Important information!

Caution! Refer to the instructions!
Caution! Disconnect plug!

Keep away from direct sunlight!
Caution! Dangerous UVC radiation!
The Filtoclear may be used with a maximum pressure of 2,9 psi

(0.2 bar)!

The Filtoclear must be removed when frost is expected!

Water inlet from the pump into the filter.

Water outlet from the filter into the pond.

Cleaning outlet from the filter into the sewerage system or onto a
flower bed, for example.

Function switch setting “Filter“.
Function switch setting “Clean“.

Pmax = 2,9 psi

(0,2 bar)

English

3

English

Unpacking

When unpacking, if external damage is visible which could impair
the functioning of important parts of the equipment, please inform
the carrier of the defects immediately , on the same day if possible,
and insist on the facts being recorded in writing. Then contact
your supplier who will take care of everything else.

Parts supplied

1 x Filtoclear pressure filter with integrated UVC
2 x spiral stepped hose adapter ½“, transparent
1 x spiral stepped hose adapter 1½“, black
1 x spiral stepped hose adapter 1½“, threaded, black
3 x union nuts 1½“
2 x flow vane
1 x flat seal
1 x instructions

Appropriate use

The Filtoclear with integrated UVC is a sealed pressure filter
system for biological and mechanical filtering of normal pond
water with a temperature of + 40°F to + 95°F. This Filtoclear
pressure filter is intended exclusively for private use for cleaning
garden ponds with or without pond fish.
Optimum cleaning is achieved in combination with the OASE
Aquamax pumps.

Important safety instructions

Warning - T o guard against injury , basic safety precautions should

be observed, including the following:

1. Read and follow all safety instructions

2. Danger - T o avoid possible electric shock, special care should
be taken since water is employed in the use of this equipment.
For each of the following situations, do not attempt repairs
yourself; return the appliance to an authorized service facility
for service or discard the appliance.

- lf the appliance falls into the water, DON’T reach for it! First
unplug it and then retrieve it. lf electrical components of the
appliance get wet, unplug the appliance immediately.

4

English

Safety guidelines

Filtoclear pressure filter with integrated UVC

- Caution: Dangerous ultraviolet radiation. The rays from

the UVC lamp are harmful to your eyes and skin! Never

operate the lamp of the Filtoclear UVC outside the casing!

- Set up the Filtoclear with integrated UVC so that it is safe from
flooding. Secure your Filtoclear so that it will not fall into the pond.
It should be placed at least 6,5 feet from the edge of the pond.

- Always turn the pump on first before starting up the Filtoclear
UVC. The UVC lamp must not be operated without water flowing
through it.

- Do not use the Filtoclear UVC if the connecting lead, UVC
lamp or casing appear to be defective!

- Do not use the Filtoclear UVC when there are people in the water!

- Caution: The built-in temperature monitor in the Filtoclear UVC
automatically switches off the UVC lamp if it overheats. After it
has cooled down, the UVC lamp is automatically switched back
on again.

- Never open the casing of the UVC or its accessories unless
expressly directed to do so in the instructions.

- The electrical data of the supply grid must correspond to the
data on the type label.

- Do not operate any appliance if it has a damaged cord or

plug, or if it is malfunctioning or if it is dropped or damaged in
any manner .

3. Always unplug an appliance from an outlet when not in use,

before putting on or taking off parts, and before cleaning. Never
yank cord to pull plug from outlet. Grasp the plug and pull to
disconnect.

4. Do not use an appliance for other than intended use. The use

of attachments not recommended or sold by the appliance
manufacturer may cause an unsafe condition.

5. Read and observe all the important notices on the appliance.

6. Save these instructions

5

English

P

max

= 2,9 psi
(0,2 bar)

min

6,5

feet

max.

6,5 feet

- Always disconnect the plugs of the Filtoclear UVC and of all devices
that are in the water before you carry out any work on the Filtoclear!

- For your own safety, contact an electrician if you have any
questions or problems regarding the electrical connection!

- Never immerse the device in water!

- Electrical installations near garden ponds and swimming pools
must comply with international and national installation
guidelines.

- Keep the connecting points dry!

- Do not carry or pull the Filtoclear by its connecting lead! Protect
the connecting lead from heat, oil and sharp edges.

- Lay the hoses and connecting lead in such a way that they are
not an obstacle and do not become damaged!

- Caution! Danger! Never operate the Filtoclear pressure filter
with integrated UVC with a water pressure greater than 2,9 psi (
0,2 bar)! The height difference between the filter lid and the
pressure-free outlet point can therefore be 6,5 feet max. The
maximum delivery pressure of the pump being used must not
exceed 7,25 psi ( 0,5 bar).

- Only operate the Filtoclear with pressure hoses that are
approved for at least 2,9 psi ( 0,2 bar), i.e. the maximum pressure
of the pump.

- Check and clean the water outlet to the pond on a regular ba­sis. The outlet should always be clear , as any blockage would
result in the filter being operated at a pressure greater than 2,9
psi ( 0,2 bar). This in turn would lead to the risk of leaking and
therefore of the pond emptying completely .

- Important: When the Filtoclear is being used in ‘filter’ mode,
the cleaning connection or any drainage hose connected to it
must always be sealed with the sealing cap and inserted flat
seal in order to prevent the pond from emptying. At the same
time the sealing cap acts as a safeguard in case the function
switch is accidentally set to ‘Clean’.

- Make sure that the function switch is always set to ‘Filter’ when
the pump is in operation. The function switch may only be set to
‘Clean’ when cleaning the filter sponges with the handle function.

6

English

Do’s

— Make sure that the unit is installed in accordance with all

National and Electrical Codes.

— Make sure to install the Filtoclear at least 6,5 feet from the

edge of the pond.
— Make sure to keep the outlet system free of dirt and debris.
— Make sure to unplug the unit before servicing the unit.
— Make sure to keep the plugs and connections dry at all times.
— Make sure to return the unit to an authorized service dealer

for any repairs.

Don’ts

— Do not exceed the “Maximum Operating Pressure” of 2,9 psi

( 0,2 bar).
— Do not carry or pull the unit by the power cord.
— Do not tamper with or operate unit without the proper ground-

ing plug.
— Do not operate the unit if the power cord appears to be defective.
— Do not operate the lamp outside of the housing.
— Do not operate the unit without water flowing through the unit.
— Do not expose eyes or skin to the lamp’s rays.
— Do not attempt any repairs on this unit.
— Do not open the casing of the Bitron or its accessories un-

less expressly directed to do so in the instructions

- Before starting up the Filtoclear, check that the connected

hoses, the sealing cap and the tension ring with safety latch
are sitting correctly .

- Never pump any liquids other than water!

- When frost is expected, you must remove the Filtoclear with

integrated UVC.

- Install the Filtoclear where it will not be exposed to direct

sunlight.

- Please observe the local noise protection regulations.

7

English

Electrical connection

Grounding instructions

This product must be grounded. If it should malfunction or break­down, grounding provides a path of least resistance for electric
current to reduce the risk of electric shock. This product is
equipped with an electrical cord having an equipment grounding
conductor and a grounding plug. The plug must be plugged into
an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.

Danger – Improper connection of the equipment-grounding

conductor can result in the risk of electrocution. Check with a
qualified electrician or service personnel if you are in doubt as to
whether the outlet is properly grounded. Do not modify the plug
provided with the product – if it will not fit the outlet, have a proper
outlet installed by a qualified electrician. Do not use any type of
adapter with the product.

Warning – To reduce the risk of electrocution, keep all connec­tions dry and off the ground. Do not touch plug with wet hands.

Ground fault circuit interrupter (GFCI)
protection

T o comply with the National Electric Code (NFPA 70) and to pro­vide additional protection from the risk of electrical shock, this
unit should only be connected to a receptacle that is protected
by a ground fault circuit interrupter (GFCI < 30 mA).

8

English

How the Filtoclear pressure filter works

The Filtoclear pressure filter with integrated UVC is a sealed filter
system for the biological and mechanical cleaning of pond water.

A Water inlet

The pump is connected to the water inlet with a pressure hose.

B Pre-clarifying of pond water

As the water flows in, it is briefly exposed to ultraviolet radiation

under the UVC lamp. This kills off germs and bacteria and

inhibits algae growth. The water subsequently flows from the

edge into the filter in a circular fashion.

C Vortex system (settling zone)

Suspended matter and bio-sludge are precipitated by the

centrifugal effect and gravity.

D Mechanical filtering

Dirt particles are trapped by the outer surface of the filter

sponges before the water flows the entire height of the filter from

the edge into the inner chamber of the filter.

GI H

F

A

C

D

E

B

J

9

Installation guidelines with regard to the
Clear Water Guarantee

OASE guarantees that this system will maintain clear water in a
pond in accordance with the following definitions, installation and
usage guidelines:

Definition of clear water:

Clear water is achieved if the fish or stones at the bottom of the
pond can be seen at a depth of 3,25 feet.

Selecting the right system

Please select the filter system using the following table (selection
criteria: pond size and with/without fish population).

E Biological clarifying

The pores of the filter sponges form a large inner surface
which microorganisms can colonise. The red and blue filter
sponges differ in size and density. This creates zones in
which the water can flow at different speeds. Zones with a
high flow speed (blue filter sponges) favour the colonisation
of microorganisms which convert ammonium to nitrate via
nitride (nitrification). Zones with a low flow speed (red filter
sponges) support the colonisation of anaerobic microorgan­isms which reduce nitrate to nitrogen (denitrification).

F Water outlet with flow indicator

At the water outlet, the clarified water is fed back into the
garden pond via a pressure hose or a watercourse etc.

G Cleaning connection

When cleaning the filter, a drainage hose can be connected
to the cleaning connection which diverts the dirty water into
a drain or onto a flower bed.

H Function switch

The function switch is used to switch between normal water
discharge into the pond (“Filter“) and the cleaning connec­tion (“Clean“).

I Cleaning the filter sponges with the handle function

The filter sponges can be cleaned while the Filtoclear is
operational through hard “pumping” by pressing the cleaning
handle.

J UVC Reflection (only Filtoclear 4.000)

English

10

The filter system with integrated UVC must be running permanently ,
24 hours a day .
The UVC lamp must be replaced after 8,000 hours of operation in
order to ensure that the Filtoclear UVC continues to operate with
optimum effectiveness.
The filter system must be cleaned regularly .

Pressure loss due to height difference

The selection table allows for a maximum height difference of
3,25 feet between the surface of the water and the highest point
of the filtering system. If the height difference is greater than 3,25
feet, you should use a correspondingly more powerful pump.

English

Pressure loss due to hoses

Use large hoses if possible in order to minimise pressure loss.
Please use the following hose diameters for hoses up to 13 feet
in length:

Filtoclear 800 1 – 1¼ inches
Filtoclear 1.600 1 – 1½ inches
Filtoclear 3.000 1¼ - 1½ inches
Filtoclear 4.000 1½ inches

1''

1 ¼''
1 ½''

¾“

Slight pollution of pond
without fish population

Heavy pollution of pond
with fish population

Aquamax Filtoclear 800 Filtoclear 1.600

1.600 SF 800 gal 400 gal 1.050 gal 525 gal

2.200 SF - - 1.600 gal 800 gal

3.000 SF - - - -

3.500 SF - - - -

Aquamax Filtoclear 3.000 Filtoclear 4.000

1.600 SF 1.600 gal 800 gal 2.100 gal 1.050 gal

2.200 SF 2.100 gal 1.050 gal 2.400 gal 1.200 gal

3.000 SF 2.640 gal 1.320 gal 3.000 gal 1.500 gal

3.500 SF 3.000 gal 1.500 gal 4.000 gal 2.000 gal

11

English

Installing and connecting the Filtoclear
pressure filter

Installing the Filtoclear pressure filter

Choose a suitable location for the pressure filter. Please note the
installation guidelines regarding the clear water guarantee as well
as the following guidelines:
– Install the Filtoclear pressure filter with integrated UVC so that

it is safe from flooding. Secure your Filtoclear so that it will not

fall into the pond. It should be placed at least 6,5 feet from the

edge of the pond.
– Place the filter on a firm and level base, e.g. on a slab. The filter

can also be buried up to the lip of the filter canister.
– Please ensure that there is unhindered access to the lid in

order to be able to carry out work on the filter, e.g. cleaning the

filter sponges.
– Never operate the Filtoclear pressure filter with integrated

UVC with a water pressure greater than 2,9 psi ( 0,2 bar). The

height difference between the lid and pressure-free outlet can

therefore be a maximum of 6,5 feet.

Connecting hoses

Decide which hose diameter you need based on the selection
table and the recommended hose according to the installation
guidelines for the clear water guarantee (page 9 and 10). Only
operate the Filtoclear with pressure hoses that are approved for a
pressure of at least 2,9 psi ( 0,2 bar) i.e. the maximum pressure
of the pump. From the OASE range, we recommend the green
spiral hose with the corresponding hose clip.
Note: We recommend warming the hose with hot water , pushing
/ twisting it onto the spiral stepped hose adapter and securing it
with a hose clip. This makes the connection more watertight.
Important!: To avoid pressure loss, cut the spiral stepped hose
adapter at the relevant point to fit each hose (see illustration).

1''
1 ¼''

1 ½''

¾“

P

max

= 2,9 psi
(0,2 bar)

min

6,5

feet

max.

6,5 feet

For hoses that are longer than 13 feet, please always use hoses
that correspond to the upper value of the scale.
In order to avoid pressure loss, cut the spiral stepped hose adapter
at the relevant points for each hose.
Avoid unnecessary corners and bends which contribute to further
pressure loss.

12

English

Connecting to cleaning connection

You can have a drainage hose permanently connected to the
cleaning connection. This allows you to drain the dirty water
directly into the sewerage system or onto a flower bed.
Important!: When the Filtoclear is being used in ‘filter’ mode,
the cleaning connection or any drainage hose connected to it
must always be sealed with the sealing cap and inserted flat seal
in order to prevent the pond from emptying. At the same time the
sealing cap acts as a safeguard in case the function switch is
accidentally set to ‘Clean’.
To connect the drainage hose, push the union nut onto the
transparent spiral stepped hose adapter. Push / twist the hose
on and secure with a hose clip. Insert the green flow vane into the
union nut and screw tight onto cleaning connection. In order to be
able to seal the open end of the drainage hose with the sealing
cap, you need to push / twist the black spiral stepped hose adapter
with thread onto the hose and secure it with a hose clip. Screw
the sealing cap and inserted flat seal on tight.

Connection to water outlet

Push the union nut onto the transparent spiral stepped hose
adapter. Push / twist the hose on and secure with a hose clip.
Insert the green flow vane into the union nut and screw tight onto
the water outlet nozzle.
Note: We recommend diverting the cleaned water via a small
watercourse, for example, instead of feeding it directly back into
the pond. This enriches the water with additional oxygen.

Connection at water inlet

Push the union nut onto the black spiral stepped hose adapter .
Push / twist the hose on and secure with a hose clip.
Insert the flat seal into the union nut and screw tight onto the
water inlet nozzle:

13

English

Starting up the pressure filter

Important! Before each start-up, you should check that the

connected hoses, the sealing cap and the tension ring with safety
latch are sitting correctly . The function switch must be set to the
“Filter“ symbol. It is imperative that you read and follow the safety
guidelines before start-up.

1. First switch on the pump
Caution! The UVC lamp must not be operated without water flowing
through it.

2. After starting up the pump, check that all the connections are
watertight. Improve those that are not.

3. Plug the Filtoclear UVC into the mains. The power indicator
lights up with a blue shimmer .

Note: In the case of a new installation, the pressure filter
only reaches its full biological cleaning effectiveness after
a few weeks. Extensive bacterial activity only starts at
temperatures of + 50°F or above.

Cleaning and maintenance of the Filtoclear

The Filtoclear pressure filter is largely maintenance-free. The fil­ter sponges should, however, be cleaned regularly .

Cleaning the filter sponges with the handle function

Suspended matter and dirt are deposited in the filter sponges
over time. These deposits reduce the effectiveness of the filter,
so the filter sponges should be cleaned regularly , e.g. every two
weeks.

Note: The filter sponges should be cleaned when cloudy
or even dirty water flows out of the water outlet and back
into the pond.
You can check how dirty the filter is at the transparent
spiral stepped hose adapter with the green flow vane at
the water outlet.

1. T wist off the sealing cap at the cleaning connection or at the
drainage hose that is connected to the cleaning connection.
Caution: There will be a small flow of water .

2. Pull the function switch up slightly and turn clockwise until it
clicks into the “Clean” position.

3. Pull the cleaning handle hard and “pump” several times. This
squeezes the filter sponges and cleans them mechanically .

4. Press the cleaning handle down until it hits the lid. The two
O-rings noticably lock into position.

14

English

5. The filter will now be rinsed clean. As soon as only clean water
can be seen through the transparent spiral stepped hose adapter
at the cleaning connection, pull the function switch up slightly
and turn anti-clockwise until it clicks into the “Filter” position.

6. Screw the sealing cap with the inserted flat seal tight onto the
cleaning connection or the drainage hose that is connected to
the cleaning connection.

7. The filter is now operational again. Check the water flow into
the pond at the green flow vane.

Washing the filter sponges

If the water flow is too small due to dirty filter sponges and cannot
be improved through cleaning with the handle function, then the
filter sponges must be washed or replaced.
Note: Do not use any chemical cleaning agents so as not to kill
off the microorganisms in the filter sponges.

1. Disconnect the mains plug of the Filtoclear UVC.

2. Switch off the pump and ensure that it cannot be switched on
unintentionally.

3. Remove all hoses by unscrewing the union nuts.

4. Remove the tension ring. T o do this, pull back the safety latch,
push in the fastening hook and open the tension ring.

5. Lift off the lid with the filter sponge assembly. Place the lid
upside down on another clean surface. The filter sponges are
lying with the filter plate facing up.

Wear marking:

The filter sponges are pre-stressed. The filter sponges can
fall apart due to the mechanical strain and due to normal
ageing. This can result in a short-circuit in the filter .
To check the filter sponges, they must lie on top of each
other on the lower filter plate without any “air gaps”. The
filter sponges must be replaced if the wear marking on the
upper plate is completely visible (see illustrations)

6. Remove upper filter plate by unscrewing the two screws.

7. Pull off the filter sponges and clean under flowing water. Give
the filter sponges a good squeeze.

15

8. Pull off the lower filter plate.

9. Clean the filter box, the lid with lattice pipe, both filter plates and
the tension ring by spraying them with a water hose.

10.Lift the bypass valve slightly and clean the inlet comb of the
Filtoclear UVC (see illustration).

1 1.Clean the lid sealing ring and the edge of the filter box.

12.Push one filter plate, with the collar facing up, onto the lattice
pipe and the cleaning rods.

13.The filter sponges are pushed on from the casing lid, starting
with a large blue filter sponge and always alternating with a
small red filter sponge. The cleaning rods lie in the two openings
of the large chamber of the filter sponges.

14.Put the filter plate on with the collar facing down. Fasten the
cleaning rods flush to the filter plate using the two screws.
Important: If the cleaning rods can be pushed through the
holes of the filter plate, the filter plate must be turned 90° onto
the other set of holes. The lattice pipe must be completely
covered by the collar diameter .

15.Place the lid seal onto the upper edge of the filter box (see
illustration).

16.Press the lid with the filter sponge assembly onto the filter box.

17.Place the tension ring onto the edge of the filter box and lid,
press down on the lid and click the fastening into place. Push
the safety latch in. Caution: Do not jam the cable of the
Filtoclear UVC!

18.Fasten all hoses with flat seals or flow vane to the
corresponding connections by screwing the union nuts on tight.

19.Start the pressure filter up again. (see “S tarting up the pressure
filter“)

English

16

Replace UVC lamp

The UVC lamp must be replaced after 8.000 hours of operation in
order to ensure that the Filtoclear UVC continues to operate with
optimum effectiveness.

1. Disconnect the mains plug of the Filtoclear UVC.

2. Switch off the pump and make sure that it cannot be switched
on unintentionally .

3. Unscrew the four screws of the Filtoclear UVC and carefully
pull the lamp from the lid of the filter. Note: The screws are
screwed in very deep (approx. 0,7 inch) in order to allow greater
torque to be applied.

4. Unscrew the clamping screw in an anti-clockwise direction
and remove the quartz tube with O-ring.

5. Pull out the UVC lamp and replace it.

Note: Due to a built-in safety switch the UVC lamp only
works after complete assembly of the Filtoclear. Only lamp s
of the type 9W UV -C, G23 may be used.

6. Clean the quartz tube with a damp cloth.

7. Check the quartz tube and O-ring for damage and replace if
necessary.

8. Screw the clamping screw with quartz tube and O-ring on tight
in a clockwise direction.

Cleaning the quartz tube

1. Disconnect the mains plug of the Filtoclear UVC.

2. Switch off the pump and make sure that it cannot be switched
on unintentionally .

3. Unscrew the four screws of the Filtoclear UVC and carefully
pull the lamp from the lid of the filter. Note: The screws are
screwed in very deep (approx. 0,7 inch) in order to allow greater
torque to be applied.

4. Clean the quartz tube with a damp cloth.

5. Pull out the flat seal and the protective tube between the lid and
the Filtoclear UVC and clean with water. Check the parts for
damage and replace if necessary . Fit the flat seal under the ring
of the protective tube (see illustration) and insert in lid together .

6. Insert the Filtoclear UVC in the lid of the filter and screw the
four screws on tight by hand (1,5 ft-lb).

7. Start the pressure filter up again. (see “S tarting up the pressure
filter“)

English

17

English

9. Pull out the flat seal and the protective tube between the lid
and the Filtoclear UVC and clean with water. Check the p arts for
damage and replace if necessary . Fit the flat seal under the ring
of the protective tube (see illustration) and insert in lid together .

10.Insert the Filtoclear UVC in the lid of the filter and screw the
four screws on tight by hand (1,5 ft-lb).

1 1 .S tart the pressure filter up again. (see “S tarting up the

pressure filter“).

Storage / winter storage

When frost is expected, you must remove the Filtoclear with
integrated UVC! Clean it thoroughly (see Cleaning and maintenance
of the Filtoclear). Check the Filtoclear with integrated UVC for any
damage. Store the Filtoclear with integrated UVC in a dry and
frost-free place. The place of storage must be inaccessible to children.

Advice on disposal

Please dispose of your Filtoclear with integrated UVC in an
environmentally friendly way. Contact your local refuse depart­ment for advice on disposal.
UVC lamps must not be disposed of with domestic waste! Remove
the UVC lamp from the unit and take it to a collection point, so
that it can be disposed of in an environmentally responsible way .

Repair / cable replacement

For repair / cable replacement please send the defective Filtoclear
with integrated UVC directly to the supplier / manufacturer .
Available spare part s are listed under Product overview.

18

Fault

Water not
getting clear

UVC lamp
indicator is
not on

No water
discharge
from pond inlet

Possible causes

• Unit not been used
for long

• Inappropriate pump
capacity

• Water is extremely
dirty

• Fish and animal
population too large

• Filter sponges are
dirty

• Quartz tube is dirty

• Mains plug of Filtoclear
UVC not connected

• Defective UVC lamp

• Faulty connection

• Lamp has no UVC
output

• Protective tube not
fitted

• Filtoclear UVC over­heating

• Function switch set
to “Clean”

• Mains plug of pump
not connected

• Pond inlet blocked

Measures

• Full biological cleaning effectiveness
is only reached after a few weeks.

• Reset pump capacity

• Remove algae and leaves from
the pond, change the water

• Guideline: approx. 2 feet fish length
to every 265 gal of pond water

• Clean the filter sponges

• Remove the Filtoclear UVC and
clean the quartz tube

• Connect the mains plug of the
Filtoclear UVC

• Replace the UVC lamp

• Check the electrical connection

• The lamp should be replaced after
approx. 8,000 hours of operation

• See Replace UVC lamp

• After cooling down, UVC
switched on automatically

• Reset function switch to “Filter”

• Connect the mains plug of the
pump

• Clean pond inlet

Troubleshooting

English

Technical data

Filtoclear 800 1.600 3.000 4.000

Dimensions in inches
(LxWxH) 14,96x14,96x12,2 14,96x14,96x17 14,96x14,96x21,6 14,96x14,96x26,4

Inlet and outlet ¾“ to 1½“ ¾” to 1½“ ¾“ to 1½“ ¾“ to 1½“
Filter volume in gallon 1,3 2,4 3,7 4,5
Crystalline filter surface 57 ft² 113 ft² 170 ft² 225 ft²
Integrated UVC clarifier 9 W 9 W 9 W 9 W
Nominal voltage UVC 120V/60Hz 120V/60Hz 120V/60Hz 120V/60Hz
Lamp components UVC 9W UV-C, G23 9W UV-C, G23 9W UV-C, G23 9W UV-C, G23
Cable length 15 ft 15 ft 15 ft 15 ft

Weight 11 lbs. 12 lbs. 13 lbs. 14 lbs.

19

English

Wearing parts

Filtoclear 800: Spare UVC lamp 9W ID No.54984

S pare filter set Filtoclear USA 800 ID No.56109
S pare set of seals ID No.34581

Filtoclear 1.600: Spare UVC lamp 9W ID No.54984

S pare filter set Filtoclear USA 1.600 ID No.56110
S pare set of seals ID No.34581

Filtoclear 3.000: Spare UVC lamp 9W ID No.54984

S pare filter set Filtoclear USA 3.000 ID No.5611 1
S pare set of seals ID No.34581

Filtoclear 4.000: Spare UVC lamp 9W ID No.561 12

Spare filter set Filtoclear USA 4.000 I D No.56884
Spare set of seals ID No.34581

Product overview

1 Filter box Filtoclear USA 800 ID N o . 24460
2 Filter box Filtoclear USA 1.600 ID No . 24461
3 Filter box Filtoclear USA 3.000 ID No . 24462
4 Filter box Filtoclear USA 4.000 ID No . 26527
5 Lid Filtoclear ID N o .24459
6 Inner lid Filtoclear ID N o. 24457
7 Spare UVC lamp 9W ID No . 54984
8 Filtoclear UVC 120V/60Hz ID N o. 25236
9 Quartz tube ID N o .22622
1 0 Lattice pipe Filtoclear USA 800 ID N o . 24853
11 Lattice pipe Filtoclear USA 1.600 ID N o .24854
1 2 Lattice pipe Filtoclear USA 3.000 ID No . 24852
1 3 Lattice pipe Filtoclear USA 4.000 ID N o .26595
1 4 Protective tube Filtoclear UVC ID N o. 34521
1 5 Spare set of control elements Filtoclear ID N o . 34579
1 6 Spare set of screw elements Filtoclear ID No . 34580
1 7 Spare set of seals Filtoclear ID No . 34581
1 8 Spare filter set Filtoclear USA 800 ID N o .56109
1 9 Spare filter set Filtoclear USA 1.600 ID N o. 56 1 1 0
2 0 Spare filter set Filtoclear USA 3.000 ID N o. 56 1 11
2 1 Spare filter set Filtoclear USA 4.000 I D N o. 56884
2 2 Cleaning rods Filtoclear USA 800 I D N o. 24749
2 3 Cleaning rods Filtoclear USA 1.600 I D N o. 24748
2 4 Cleaning rods Filtoclear USA 3.000 I D N o. 24747
2 5 Cleaning rods Filtoclear USA 4.000 I D N o. 26596
2 6 Additional pack Filtoclear USA

800 / 1.600 / 3.000 / 4.000 ID No.34617

2 7 T ension ring Filtoclear ID No.34578
2 8 Protective tube with reflector plate (4.000 only) ID No.35256

20

English

5

6

7/ 8

9

10

17

17/18

27

18/27

16

16/18

16(2x)/17(12x)

25

18/27

17(12x)

18

17

17

18

17

17/18

17

18

15a/15b/28

18

18

21

English

1/2/3/4

11/12/13/14

16/17

16

19/20/21/22

18

23/24/25/26

19/20/

21/22

18

28

16/18

17