OAKWORKS Powerline, Seychelle, Powerline Flat Top, Powerline Wave Backrest, Seychelle Flat Top User Manual

USER MANUAL

OAKWORKS®

Treatment Tables

Seychelle™ Series

Powerline Series

www.oakworks.com · 717.235.6807

made in the USA

with US & imported parts

© Copyright 2018
OAKWORKS® , Inc.

Printed in U.S.A.

All rights are reserved. No part
of this document may be
photocopied, reproduced or
translated to another language
without prior written consent
of OAKWORKS®, Inc.

OAKWORKS® is a registered
trademark of OAKWORKS®, Inc.

Notice

The information contained within this
document is subject to change
without notice and should not
be construed as a commitment by
OAKWORKS®, Inc.

OAKWORKS®, Inc. encourages requests
for technical specifications and the
like documentation to ensure accu­racy. The appropriate documentation
is available upon request.

OAKWORKS®, Inc. shall not be
liable for incidental or consequential
damages in connection with or arising
out of the furnishing, performance, or
use of this document and the program
material which it describes.

TABLE OF CONTENTS

Product Use Description ............................................................................................................................. 1

Important Safety Instructions ..................................................................................................................... 1

Product Description & Photo

Powerline Series ............................................................................................................................... 2-3

Seychelle Series ................................................................................................................................ 4-5

Installation

Table Assembly ....................................................................................................................................6

Inset Shelf .............................................................................................................................................. 6

Directions for Use

Paper Roll Holder Use ........................................................................................................................ 7

Wave Backrest Use ............................................................................................................................. 7

Table Extender .................................................................................................................................... 7

QuickLock Face Rest .......................................................................................................................... 8

Cleaning & Disinfection

Recommended Cleaners/Disinfectants ........................................................................................ 9

Cleaning Process ................................................................................................................................. 9

Inspections ....................................................................................................................................................10

Warranty Information ................................................................................................................................10

Model Number & Serial Number .............................................................................................................11

Specifications

Product Specifications .................................................................................................................. 12

Environmental Conditions ........................................................................................................... 12

Contact Information .................................................................................................................. back cover

PRODUCT USE DESCRIPTION / IMPORTANT SAFETY INSTRUCTIONS

PRODUCT USE DESCRIPTION

The Oakworks Powerline & SeychelleTM Tables are used to support the patient during examinations
and procedures. They are intended to be operated by a professional in a exam/treatment environ­ment. No special training is required but a review of the following manual is important for the
safety of the operator and patient. The professional should read and understand this entire manu­al before use with a patient. There are no known contraindications to the use of this equipment.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

This symbol, when used in this manual and on product labels, represents a caution warning. Be
sure to read and comply with all precautions and warnings.

The Backrest section is not designed to support the entire weight of the patient. Do not sit on
the Backrest section.

The table is designed to be a stand alone table. This table must not be modified or incorporated
into any other equipment.

There are potential pinch points around and underneath the tabletop. It is the responsibil­ity of the operator of this equipment to insure that bystanders are not in the area below or
around this equipment during operation.

Proper operation of this equipment is very important for the safety of the operator, patient,
and any other individuals in the area of this equipment. Directions for use of this equipment
are described in this manual. The operator should read these sections carefully.

Do not use outdoors.

Use this furnishing only for its intended use as described in this manual. Do not use attachments not
recommended by Oakworks.

Weight Limit: (patient and accessories) 500 lbs./227 kg. Do not exceed.

READ AND SAVE THESE INSTRUCTIONS

1

PRODUCT DESCRIPTION

Powerline Flat Top

Accessory outlets

QuickLock Face
Rest (accessory)

Table Extender
(accessory)

Upholstered Top

Paper Roll Holder

Accessory outlets

STANDARD SPECIFICATIONS

Height Range Fixed 30” (76 cm.)

Table Capacity 500 lbs. (226 kg.) (patient and accessories)

Widths 27” (69 cm.) or 30” (76 cm.)

Length 72” (183 cm.)

Padding 2.5” (6 cm.) Semi-Firm

Upholstery Terra Touch™

Paper Roll Holder Accommodates up to 21” (53 cm.) rolls

(roll not included)

Table Weight

*

90 lbs. (41 kg.)

OPTIONS & ACCESORIES

QuickLock Face Rest

Table Extender

Inset Shelf (adds 25 lbs. (11 kg.))

Padding - 1.75” (4 cm.) Firm Response

2

PRODUCT DESCRIPTION

Powerline Wave Backrest

QuickLock Face
Rest (accessory)

Table Extender
(accessory)

Accessory outlets

Upholstered Top

Inset Shelf (option)

STANDARD SPECIFICATIONS

Table Height Fixed 30” (76 cm.)

Wave Backrest Manual 0-60º, 6 set positions

Table Capacity 500 lbs. (226 kg.) (patient and accessories)

Widths 27” (69 cm.) or 30” (76 cm.)

Length 72” (183 cm.)

Padding 2.5” (6 cm.) Semi-Firm

Upholstery Terra Touch™

Paper Roll Holder Accommodates up to 21” (53 cm.) rolls

(roll not included)

Table Weight

*

90 lbs. (41 kg.)

OPTIONS & ACCESORIES

QuickLock Face Rest

Table Extender

Inset Shelf (adds 25 lbs. (11 kg.))

Padding - 1.75” (4 cm.) Firm Response

Wave Backrest

Accessory outlets

Paper Roll
Holder

3

PRODUCT DESCRIPTION

Seychelle Flat Top

Accessory outlets

QuickLock Face
Rest (accessory)

Table Extender
(accessory)

Upholstered Top

Accessory outlets

Inset Shelf (option)

STANDARD SPECIFICATIONS

Height Range Fixed 30” (76 cm.)

Table Capacity 500 lbs. (226 kg.) (patient and accessories)

Widths 27” (69 cm.) or 30” (76 cm.)

Length 72” (183 cm.)

Padding 3” (8 cm.) Comfort

Upholstery Terra Touch™

Table Weight

*

90 lbs. (41 kg.)

OPTIONS & ACCESORIES

QuickLock Face Rest

Table Extender

Inset Shelf (adds 25 lbs. (11 kg.))

Padding - 4” (10 cm.) Comfort

4

PRODUCT DESCRIPTION

Seychelle Wave Backrest

Wave Backrest

QuickLock Face
Rest (accessory)

Table Extender
(accessory)

Accessory outlets

STANDARD SPECIFICATIONS

Table Height Fixed 30” (76 cm.)

Wave Backrest Manual 0-60º, 6 set positions

Table Capacity 500 lbs. (226 kg.) (patient and accessories)

Widths 27” (69 cm.) or 30” (76 cm.)

Length 72” (183 cm.)

Padding 3” (8 cm.) Comfort

Upholstery Terra Touch™

Table Weight

OPTIONS & ACCESORIES

QuickLock Face Rest

Table Extender

Inset Shelf (adds 25 lbs. (11 kg.))

Padding - 4” (10 cm.) Comfort

Upholstered Top

*

Accessory outlets

Inset Shelf (option)

90 lbs. (41 kg.)

5

INSTALLATION

TABLE ASSEMBLY

Tools Required:
9/16” / 14mm Wrench/Socket

SUPPLIED PARTS:

TOOLS

1 - Large Allen Wrench
1 - Small Allen Wrench

The tables are shipped complete in one box. Follow the step
below to fully assemble the table:

1. Remove the table from the box and place it down on the floor with the
top down. Remove all hardware and the Leg Brace.

2. Unfold the legs to a vertical position and remove any protective wrappings.

3. Install the long large bolts, reinforcement plates, spring washers and lock
nuts as shown, two bolts on each leg. Using the large allen wrench and 9/16” /
14mm wrench socket, tighten every bolt/nut connection -- 8 total -- to 12 ft-lbs
minimum or until the spring washers are flat.

LEG HARDWARE

8 -Reinforcement Plates
16 - Spring Washers
4 - Long Large Bolts
4 - Lock Nuts

LEG BRACE

1 - Wood Leg Brace
2 - Short Bolts
2 - Barrel Nuts

4. Install the barrel nut into the leg brace being sure the screw slit is horizontal.
Install the short bolt through the leg rail. Start the bolt into the barrel nut using
your fingers first. After the bolt has started, tighten the bolt using the small
allen wrench. Make sure the leg brace is flush with the adjoining rails while
tightening bolts. Repeat on opposite end of the leg brace.

5. Turn your table right side up. Get up on the table and rock back and forth
to check that all bolts are tight. The table should be very stiff. Dependent
on the environmental conditions of your table, it may be necessary to
periodically re-tighten the hardware.

Leg Brace

Barrel Nut

SHELF ATTACHMENT

If you have ordered a shelf, drop the shelf into place with the finished side up. The shelf has groves at
both ends that enable it to be held firmly in place by the legs. If necessary, the shelf can be further sta­bilized by installing the enclosed Velcro™ strips. Place strips on each corner of the shelf’s bottom side,
and on each end of the rails. Make sure not to mismatch Velcro™ strips; place all “hook” or all “loop”
pieces on either the rail or shelf.

Short Bolt

6

DIRECTIONS FOR USE

PAPER ROLL HOLDER USE

After the table is set-up,
locate the hole in the leg.

Using the supplied
screw & allen wrench,
secure the paper roll
holder bracket into
place. Repeat step for
the opposite side.

WAVE BACKREST USE

CAUTION

TO RAISE THE BACKREST

Lift the backrest to the desired height and
release. The Backrest support arm will lock in
the nearest slot in the side rail.

Do not adjust the Backrest with a patient on the table.

Locate the wooden
dowel & feed it thru
your paper roll. Place the
wooden dowel in the
groove located in each
of the paper roll holder
brackets.

To secure the wooden
dowel, feed it into the
pocket of the groove
on both sides of the
table.

TO LOWER THE BACKREST

Lift the backrest slightly, lift and hold the
support arm out of the slot and lower the
backrest to the desired position.

TABLE EXTENDER

CAUTION

The Table Extender lengthens
the table for your tallest clients
and can improve access to your
patient.

Do not put excessive weight or pressure on the table extender.

Locate the Accessory attach­ment outlets.

Unfold the dowels and insert
into the outlets.

7

DIRECTIONS FOR USE

QUICKLOCK FACE REST

CAUTION

Double articulating action provides nearly limitless positioning options with the QuickLock™ Face
Rest. The adjustable pad takes pressure off sensitive facial areas while providing superb support. The
QuickLock™ Face Rest can be used in both prone and supine positioning and folds out of the way
when not in use. Adjustments are made easily by loosening the cam locks, adjusting for height and
angle and then locking the cam locks into the desired position.

Do not put excessive weight or pressure on the Quicklock Face Rest. Do not extend the
dowels of the Quicklock Face Rest 3” (7.6 cm.) from the table top. The Maximum Weight
Capacity for the QuickLock Face Rest is 25 lbs. (11 kg.)

QuickLock™
Face Rest

* U.S. Patent #5,177,823

Important Safety Note:

Maximum Distance from edge
of Table Top= 3” (7.6 cm.)

Insert dowels into
Accessory attachment out­lets.

Loosen Cam Locks &
adjust face rest into place.

Tighten the Cam Locks.

The Face Rest can be used
for either prone or supine
positioning.

8

CLEANING & DISINFECTION

RECOMMENDED CLEANERS/DISINFECTANTS

DANGER

The following cleaners were tested by OAKWORKS® and found to be acceptably compatible with all materials used in
construction of our tables:

1. Formula 409

2. Fantastik

3. Green Windex

The following disinfectants were tested by OAKWORKS® and found to be acceptably compatible with all materials
used in construction of our tables:

1. Parker Labs: ProtexTM (EPA reg# 6836-152-82613)

2. Healthlink® E-Z Kill® (EPA reg# 59894-10-67454)

3. MADA Medical: Madacide-FD (EPA reg# 1130-15-11703)

The following disinfectants were tested by OAKWORKS® and found to be acceptably compatible with most materials,
with some cautions as indicated:

1. 10% Sodium Hypochlorite (bleach) solution in water (EPA reg# 5813-100) (possible mild corrosion of
plated metals)

2. Metrex Cavicide One (EPA reg# 46781-12) (possible slight deterioration of upholstery and wood lacquer)

OAKWORKS® recommends a prepackaged wipe for cleaners/disinfectants to ensure best distribution of disinfectant
for the required kill time, without leaving excess residue and/or overexposing components therefore minimizing the
potential for damage to materials. Please read and follow disinfectants manufacturers’ directions for cleaning and dis­infection.

®

®

To reduce the risk of electric shock:

- Always unplug this furnishing from the electrical outlet before cleaning.

®

The following disinfectants were tested by OAKWORKS® and found to be incompatible with some materials and are
therefore NOT recommended for use:

1. Clorox Broad Spectrum Quaternary (EPA reg# 67619-20)(deterioration of upholstery, wood lacquer,
plated metals)

2. Clorox Hydrogen Peroxide Disinfectant (EPA reg# 67619-24)(corrosion of metals, deterioration of
upholstery and wood lacquer, leaves a hard-to-remove residue)

3. Virox Accel TB (EPA reg# 74559-1)(corrosion of metals, deterioration of upholstery and wood lacquer,
leaves a hard-to-remove residue)

4. Clorox Healthcare Bleach Germicidal Cleaner (EPA reg# 56392-7)(deteriorates upholstery, wood
lacquer, mild corrosion of metals, dissolves foam in pads)

OAKWORKS® does NOT recommend the use of cleaners/disinfectants containing Hydrogen Peroxide, Acetic Acid, or
Phenolics. These chemicals can cause damage to the appearance and/or material integrity of various components.
Also, while the recommended cleaners/disinfectants list includes products containing Quaternary Ammonium com­pounds (“quats”), not all products containing quats are approved for use. Some contain additional detergents and/or
surfactants which can be detrimental to some materials.

A note on Bleach: While a 10% sodium hypochlorite (household bleach) solution (EPA reg# 5813-100 or equivalent)
can be an effective disinfectant and is dilute enough to be benign to most materials, it alone is not an effective clean­er and a separate product must be used for the initial cleaning steps of the procedure. Because of possible chemical
incompatibilities between various cleaning products and bleach, utmost care must be taken by the user to avoid
potential exposure to harmful or toxic by-products of the combination. Also, because bleach leaves a potentially cor­rosive residue as it evaporates, it must be rinsed with clean water after disinfection. It is therefore NOT recommended
by OAKWORKS®. Please note, one step cleaner/disinfectants using bleach and a detergent/ surfactant were found to
damage materials and are NOT recommended.

9

CLEANING & DISINFECTION / INSPECTIONS / WARRANTY

CLEANING & DISINFECTIONCLEANING PROCESS

DANGER

Follow the cleaners/disinfectant manufacturers’ directions for use. Please note that cleaning and disinfecting an OAKWORKS® table
is a two part process. First it must be cleaned of any visible soil, then it can be disinfected. The table should be cleaned as soon as
possible after use. Please follow these procedures for best results:

1. Using a fresh wipe or wipes, clean any visible soil off of the table, working from the top to the bottom of the table.

2. Throw the used wipe(s) away.

3. Using a fresh wipe or wipes, thoroughly wipe all surfaces of the tabletop and any high-contact areas such as handles, hand­sets, etc., making sure they remain wet for the disinfectant manufacturer’s recommended contact time.

4. Throw the used wipe(s) away and allow the table to dry.

To reduce the risk of electric shock:

- Always unplug this furnishing form the electrical outlet before cleaning.

INSPECTIONS

RECOMMENDED REGULAR INSPECTIONS (monthly or local standard)

• Check for damage to the power, hand control(s) and foot control(s) on all cables.

• Visually inspect components for obvious damage that could cause problems during operation.

RECOMMENDED PERIODIC INSPECTIONS (yearly or local standard)

• Check for damage to the power, hands control and foot control cables and all visible wiring.

•Visuallyinspectcomponentsforobviousdamagethatcouldcauseproblemsduringoperation.

•Checkallmechanicalfunctionsusingthehandcontrol.Repeatusingthefootcontrol.Checkforabnormalnoises.

•Checkthatallfastenersarepresentandfastenedsecurely.

•Checktablegrounding.

•Cleanunusualbuildupofdirtonthetableand/orpartsofthetablenotnormallycleanedonaregularbasis.

•Checkfortearsorcracksintheupholstery.

WARRANTY

View complete warranty details at www.oakworks.com

10

MODEL NUMBER & SERIAL NUMBER

MODEL & SERIAL NUMBERS

The model number and
serial number are located
under the top of the table.

Model Number

MODEL NUMBER DESCRIPTION

PWMPBRXX XXXXFRTT XX XX

Serial Number

16796025 PWMPBR303072SFTTZZAS
Ser#: PWK1565022
PWK Powerline Backrest 30 x 30 x 72 FR/TT/XX
TTSKYBLUE 01/04/2013 Order#:654321
Notes: Sample Product Label

Model Numbers and Serial Numbers always start with a letter.

Options

Not Used

Fabric: TerraTouch

Padding

FR=1.75” (4 cm.) Firm Response
SF=2.5” (6 cm.) Semi-Firm
PL=3” (8 cm.) Comfort
AC=4” (10 cm.) Comfort

Table Top Length

Minimum Table Height

Table Width

To p

FT=Flat Top
BR=Wave Backrest

Base

Table

PW=Powerline Series
SE=Seychelle Series

11

SPECIFICATIONS

PRODUCT SPECIFICATIONS

Weight 90-115 lbs. (41-52) kg.

Shipping Weight 105-130 lbs. (48-59 kg.)

Weight Limit 500 lbs. (226 kg.)

ENVIRONMENTAL CONDITIONS

Conditions Temperature Humidity Atmospheric Pressure

Normal Use 50° (10°C) to 104° (40°C) 20% to 60% RH 98 to 105 kPa

Storage & Transport -20° (-29°C) to 135° (57°C) 20% to 95% RH 98 to 105 kPa

12

USER MANUAL

OAKWORKS®

Treatment Tables

CONTACT INFORMATION:

OAK WORKS® Inc.

923 East Wellspring Road
New Freedom, PA 17349

Phone: [phone]

FAX: [phone]

www.oakworks.com

For user manuals & instructional videos

related to your product, please visit

http://www.oakworks.com/manuals.asp

Manual Part Number MMMNST0005-EN
Revision level: 3
Revision Date: 03/06/2019

English, Printed in USA

made in the USA

with US & imported parts