All rights are reserved. No part
of this document may be
photocopied, reproduced or
translated to another language
without prior written consent
of OAKWORKS®, Inc.
OAKWORKS® is a registered
trademark of OAKWORKS®, Inc.
Notice
The information contained within this
document is subject to change
without notice and should not
be construed as a commitment by
OAKWORKS®, Inc.
OAKWORKS®, Inc. encourages requests
for technical specifications and the
like documentation to ensure accuracy. The appropriate documentation
is available upon request.
OAKWORKS®, Inc. shall not be
liable for incidental or consequential
damages in connection with or arising
out of the furnishing, performance, or
use of this document and the program
material which it describes.
TABLE OF CONTENTS
Product Use Description ....................................................................................................1
Important Safety Instructions
Symbol Identification ........................................................................................................1
PRODUCT USE DESCRIPTION / IMPORTANT SAFETY INSTRUCTIONS
PRODUCT USE DESCRIPTION
OAKWORKS® Imaging Tables are radiographic tables intended for use with mobile or compact stationary C-arm
Imaging Systems. It is ideally suited for pain management imaging and therapeutic procedures. These tables are
suitable to use for diagnostic x-ray imaging and imaging during therapeutic procedures such as spinal injections,
vertebroplasty procedures and other pain management procedures. The CFLU and CFUR Tables are designed for
Lithotripsy and Urology procedures. It is intended to be operated by a healthcare professional in a medical environment. No special training is required but a review of the following Safety Instructions is important for the safety of the operator and patient. The healthcare professional should read and understand this entire manual before
use with a patient.
NOTE The EMISSIONS characteristics of this equipment make it suitable for use in industrial areas and hospitals
(CISPR 11 class A). If it is used in a residential environment (for which CISPR 11 class B is normally required) this
equipment might not offer adequate protection to radio-frequency communication services. The user might need to
take mitigation measures, such as relocating or re-orienting the equipment.
SYMBOL IDENTIFICATION
This symbol, when used in this manual and on product labels, represents a caution warning. Be sure to
read and comply with all precautions and warnings.
This symbol, when used in this manual and on product labels, warns against an electrical shock hazard. Be
sure to observe and comply with all warnings.
~
----
This symbol, when used in this manual and on product labels, indicates the potential of exposure to harmful
x-rays. Be sure to read and comply with all warnings.
This symbol, when used in this manual and on product labels, indicates that the table and components
are a Type B Applied Part pursuant to IEC 60601-1: 2005.
This symbol, when used in this manual or on product labels, indicates a Protective Earth (Ground)
Terminal.
This symbol, when used in this manual or on product labels, indicates the date of manufacture of the
device.
This symbol, when used in this manual or on product labels, indicates alternating current (AC).
This symbol, when used in this manual or on product labels, indicates direct current (DC).
This symbol is used to indicate that the operator should consult the user manual.
Sitting is prohibited in this area.
CONTRAINDICATIONS
The Oakw ork s® Imaging Tables should not be used with Imaging systems having intensifier screens or film cassettes larger than 12 inches (30 cm) when an oblique angle of view is being used. The tables are not designed for
and should not be used with Magnetic Resonance Imaging procedures.
1
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
After unpacking your table, inspect it thoroughly for damage. If you suspect a problem do not use the table and
call our customer service department at 800-916-4612.
Improper use of this device can cause injury. Be sure to read all operating instructions prior to use.
IMPORTANT - If the Foot Control is ordered, you must install a Foot Control Cradle per Installation Instruction part
number MMINMD0008-EN.
Weight limit (patient and accessories): 227 kg / 500 lbs. distributed evenly. (Bariatric Table only: 340 kg / 750 lbs.)
Do not sit beyond warning line on carbon fiber top. On Lithotripsy / Urology Top - Do not sit on any extensions
(Weight Limit: 200 lbs. / 91 kg.)
The table utilizes four locking casters to permit movement of the table within the imaging suite. Accidental movement of the table may occur. Lock casters prior to accomplishing imaging of the patient. Lock casters when the
patient is mounting & dismounting the table.
The table should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary,
the table should be observed to verify normal operation in the configuration in which it will be used.
The use of Accessories, transducers, and cables other than those specified (with the exception of transducers and cables
sold by the Manufacturer of this device as replacement parts for internal components) may result in increased Emissions
or decreased Immunity of the table.
The table is designed to be a standalone table used with radiographic equipment. This table must not be modified or
incorporated into any other equipment.
There may be pinch points under the table top. Do not have any body part under the top when the table is in
motion.
READ AND SAVE THESE INSTRUCTIONS
Be certain that the table is completely lowered prior to discharging an ambulatory patient. The patient may lose balance
and fall. NOTE: The CFPMFXH is a fixed height table. It is recommended that all patients are assisted onto the table
(physical assistance & step stools with side rails is recommended.)
Patient must be secured with Safety Restraint Strap prior to using the tables.
Medical Electrical Equipment needs special precautions regarding EMC and needs to be installed and put into
service according to the EMC information provided in the specifications at the end of this manual. (Excluding
CFPMFXH)
Portable and Mobile RF Communications Equipment can affect Medical Electrical Equipment. (Excluding
CFPMFXH)
This table is not suitable for use in the presence of flammable anesthetic mixture with air or oxygen or nitrous oxide.
Electrical Shock Hazard. (Excluding CFPMFXH) The power supply/control module is located inside the lifting
column and under the top. No user serviceable parts are inside. Refer servicing to qualified personnel. Unplug wall
connector prior to contact with any cables connected to the power supply.
To avoid the risk of electric shock, this equipment must only be connected an outlet this is properly grounded. See
GROUNDING instructions in this manual.
Grounding reliability can only be achieved when this equipment is connected to an equivalent 3 prong receptacle
marked “Hospital Only” or “Hospital Grade”.
Oakworks medical tables are designed and built to provide many years of dependable service. Please follow local
regulations and laws when disposing of the electrical components used in this table.
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of burns, fire, electric shock or injury to persons:
1. Unplug this furnishing from the electrical outlet before cleaning.
2. Unplug from outlet before adding or removing parts.
3. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Contact Oakworks Customer Service before use.
4. Keep the cord away from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
DANGER
The potential of exposure to harmful x-rays exists when this table is in use. The use of adequate x-ray barrier
devices is necessary to provide protection to both the operator and the patient. X-ray barrier devices are recommended
for the patient outside of the intended target area to prevent exposure to scattered radiation from the x-ray generating source.
The tabletop has a typical aluminum filtration equivalence of 1.10 mm as measured at 100 kVp and a half value (HVL)
of 3.6 mm. (NOTE: Bariatric Top has a typical aluminum filtration equivalence of 1.50 mm. as measured at 100 kVp
and a half value (HVL) of 3.6 mm.)
• Oak wor ks® Imaging Tables may be used for x-ray imaging where the x-ray generator is located below the
tabletop and the image receptor is located above the tabletop. This is the recommended method. The tables may
also be used for x-ray imaging where the x-ray generator is located above the tabletop and the image receptor is
located below the tabletop. This application will result in greater patient exposure to x-rays. The operator must
weigh this issue with the imaging requirements and patient exposure issues.
•The Imaging Tables may be used with the x-ray generator above the tabletop and a film cassette located on
the tabletop. (See contraindications regarding film cassette size.)
•The x-ray generator should never be located above the tabletop when the Oakw orks® Imaging Table and
the Oakw ork s® Spine Positioning System/Prone Pillow are used together. This type of use requires that the x-ray
generator is located below the tabletop and the imaging intensifier or film cassette located above the tabletop.