Oakworks Attaching Bolster Arm Rest User Manual

Toll Free Phone: [phone] Phone: [phone]

Toll Free FAX: [phone] FAX: [phone]

www.oakworks.com

Part no. 6491, rev. 0205

Parts Included:

Tools Needed:

(not included)

Pencil
Ruler

1 - set of Bolster

Arm Rests

1 - set of Bolster

Arm Rest Straps

8 - Velcro Strips

• Turn table upside down.

• Remove paper backing from velcro strips and place velcro strips
carefully on the inside of each side rail at points 8

1

/2" and 23

1

/2" from the hinge rail, adhesive side down. (Fig. 1) Make sure

the velcro is contacting only wood and press into place.

Note: If you install the velcro on the inside of the table frame,

you should wait 24 hrs before use.

Set-up Instructions:

• Turn table upright and place the straps across the table. (Fig.2)

• Attach straps to the velcro strips on the inside of the side rail.
(Fig 3)

• Attach the Bolster Arm Rests to the table by attaching the velcro
tabs on the bolsters to the velcro on the table straps. (Fig 4 & 4a)

Other Uses for Your Bolster Arm Rests:

• Detach your Bolsters from the straps and use them to provide
support under knees and ankles.

• Your new Bolster Arm Rests will comfortably cradle your client’s
arms and effectively widen your table by 6".

• The standard strap is long enough to fit tables 24"-31" wide.
Tables that are 33" wide require a special, longer strap. Contact
Customer Service for information on this option.

WARNING

Your Bolster Arm Rests are only meant to support client’s
arms when they are lying supine or prone. They are not
meant to support clients getting on or off the table or
therapists sitting on the edge of the table.

Fig. 1

Fig. 4a

Fig. 3

Fig. 2

Fig. 4

Instructions for Installation

(not applicable if ordered with a table):

Bolster Arm Rest Installation Instructions

OAKWORKS®, Inc.

923 East Wellspring Rd., New Freedom, PA 17349

Side Rail

Velcro Strips

Velcro on Bolsters

Hinge Rail

23 1/2"

8 1/2"

Vel c ro

on

Straps

Toll Free Phone: [phone] Phone: [phone]

Toll Free FAX: [phone] FAX: [phone]

www.oakworks.com

* U.S. Patent #5,177,823

1 -set of Recess

Fillers

1 - set of Recess

Filler Straps

1. Center the Recess Filler Straps placing velcro (hook) side down,
from left to right on the top of the table, making sure they are
parallel to each other. (Fig. 1)

2. Locate the velcro strips adhered to the table frame or attach strips
provided in this package. (Fig. 2) Attach one strap to the velcro
under the table. Press firmly on straps to securely fasten the velcro.
Repeat for the second strap.

Note: If you install the velcro on the inside of the table frame, you

should wait 24 hrs before use.

3) Each Recess Filler has a 2" wide strip of velcro (hook) sewn onto
the flat side. (Fig. 3) Attach the velcro (hook) on the Recess Filler to
the velcro (loop) on the Recess Filler Strap attached to the table.
(Fig. 4) Repeat for second Recess Filler.(Fig. 5)

CAUTION:

Your Advanta Recess Fillers are only meant to support a
client’s arms when they are lying supine or prone. They will
not support clients getting on or off the table or therapists
sitting on the egde of the table.

Fig. 1

Fig. 2 Fig. 2a

Fig. 3

Fig. 5

Instructions for Attachment:

Attaching Recess Fillers

to Your Advanta Table

OAKWORKS®, Inc.

923 East Wellspring Rd., New Freedom, PA 17349

Parts Included:

Fig. 4

Velcro on Bolsters

Vel c ro

on

Straps

Vel c ro

on

Recess

Fillers

Recess

Filler

Straps

2"

Recess Filler

Attached

8 - Velcro Strips

(Retro Fit Kit only)