NY Wholesale Intercom DT607FE-ID-S1, DT607FE-ID-S2, DT607FE-ID-S3, DT607FE-ID-S4 User Manual

DT-ENG-DT607-V1 / 201609

2 WIRE SYSTEM

DT607 Series

Fisheye door station with proximity access control

USER MANUAL

RF CARD

• Please read this manual carefully to ensure safe and correct operation.

• Keep this manual well for future reference.

RF CARD

DT607F/ID/FE-S4DT607/ID/FE-S3 DT607/ID/FE-S4

RF CARD

DT607A/ID-S4DT607/ID/FE-S1 DT607/ID/FE-S2

RF CARD

CONTENTS

PARTS AND FUNCTIONS ..................................................................................... 3

Part Names............................................................................................................. 3

Mounting ................................................................................................................. 4

BASIC FUNCTIONS .............................................................................................. 6

Unlock Operations .................................................................................................. 6

Fisheye Camera ..................................................................................................... 6

External Motion Detection ...................................................................................... 6

SETUP INSTRUCTIONS ........................................................................................ 7

Functions Setting Up .............................................................................................. 7

Setting Door Station Address .................................................................................8

Setting Camera Resolution..................................................................................... 9

Setting Unlock Mode .............................................................................................. 9

Setting Unlock Time............................................................................................... 10

Setting Nameplate Illumination Mode .................................................................... 10

Setting Night View LED Illumination Mode ............................................................ 11

Setting Ring-back Tone ......................................................................................... 11

Setting Image Display Mode.................................................................................. 12

Registering ID Card ............................................................................................... 13

WIRING ................................................................................................................. 16

Connecting Electric Lock ....................................................................................... 16

How to hook up a door release.............................................................................. 18

One apartment connection .................................................................................... 18

Two apartments connection...................................................................................19

Three apartments connection ................................................................................ 19

Four apartments connection .................................................................................. 20

Connecting Multi Door Stations ............................................................................. 20

APPENDIX ............................................................................................................ 21

Precautions............................................................................................................ 21

Specication .......................................................................................................... 21

Cables and Requirments ....................................................................................... 22

PARTS AND FUNCTIONS

Part Names

Surface mounted

[13]

Flush mounted

[11]

[12]

[11]

[12]

[10]

[1]

[9]

[8]

[7]

[6]

[5]

[14]

[9]

[8]

[2]

[3]

[4]

[1]

[2]

[3]

[13]

[1] Microphone

[2] UNLOCK indicator

[3] CALL indicator

[4] Call button

[5] Nameplate

[6] Front panel

[7] Speaker

[8] Night view LED

[9] Camera lens

[7]

[4]

[6]

[5]

[10] Rainy cover

[11] Mounting hook

[12] Connection port

[13] Screw hole

[14] Mounting box

-3-

PARTS AND FUNCTIONS

Mounting

The installation height is suggested to 145~160cm.

Surface mounted

1 2 3 4 5

The distance between

Main unit

the top of main unit and rain cover should be not less than 3mm.

Rainy cover

≥0.12 inch

Main unit

AcDbMLeader (ACDB_MLEADER_CLASS)

Rainy cover

1. Connect the cable correctly.

2. Drill holes in the wall to match the size of screw stoppers,then attach the rainy cover and main unit to the wall,and the distance between the top of main unit and rain cover should be not

less than 0.12 inch.

3. Install the name plate.

4. Attach the front panel to the main unit.

5. Use the special screwdriver and the screws to x the panel.

Flush mounted

1 2 3 4 5

AcDbMLeader (ACDB_MLEADER_CLASS)

1. Drill a hole in the wall to match the size of mounting box,then attach the mounting box to the wall.

2. Loosen the high screws to install the name plate.

3. Connect the cable correctly.

4. Attach the front panel to the mounting box,then use the special screwdriver and the screws to

x the panel.

5. Finish the installation.

* The camera angle view of surface mount model may be less than 1700.

-4-

AcDbMLeader (ACDB_MLEADER_CLASS)

PARTS AND FUNCTIONS

Terminal description

1 2 3

+12V

GND

PIR

Lock Control Jumper

S-

S+

PIR Motion Detector Connect Port

Main Connect Port

Lock Control Jumper:

Motion Detector Connect Port:

Main Connect Port:

L1,L2:

•

Connect to the bus line, no polarity.

PL:

External lock power input, connect to the power positive(power +).

S+:

Lock power(+) output.

S-:

Lock power(-) output, connect to the power(-) input of locks(only when using the door

To select the lock type.

To connect external PIR motion detector.

To connect the bus line and the electronic locks.

station to power the locks, if using the external power supply for the locks, the S- will not be connected).

-5-

BASIC FUNCTIONS

detector

Unlock Operations

Unlocking of ID Card

When the registered user card has been shown to ID card window, the UNLOCK indicator lights

up, the buzzer sounds,and the electric door strike is unlocked.

• If show the authorized user card,the buzzer will sound of beep+,and the UNLOCK indicator will light up.

• If show the unauthorized user card,the buzzer will sound of beep,beep,beep.

Fisheye Camera

Please note that this function requires the

monitor with sheye function to support.

The angle view is 1700,visitors in this angle

view can be seen clearly and can be zoomed

to see individuals up close via indoor monitor

with sheye function.

Standard

door station angle

DT607

1700 door camera angle

(Wide angle view shown)

External Motion Detection

The door station is equipped with a terminal to

connect external motion detector.

If the external motion detector is connected

to the system,following functions will be effec-

tive:

If detect someone passing by, the door station

can be activated operation to unlock or turn

on light.

* Please contact with supplier for more details about detector connection.

-6-

12V

GND

PIR

Motion

SETUP INSTRUCTIONS

Functions Setting Up

This section explains the settings of each

function,please refer to the following table:

To perform the settings for the function

you want,you should move away the metal

front panel. Please refer to the sketch

map.

Each operation is indicated by the lighting

up of the

LED

indicator on the unit, and by

the sounding of the buzzer.

Order Setting items Setting range Default value

1 Setting door station address 0~3 0

2 Setting camera resolution High/Low High

LED_NAME

RF CARD

LED_UNLOCK

LED_TALK

KEY_SET KEY_4

KEY_3

KEY_2

KEY_1

3 Setting the unlock mode 0:opened/1:closed 0:opened

4 Setting the unlock time 01 to 99 seconds 1 seconds

7 Setting ring-back tone

8 Setting image display mode

Setting the nameplate

illumination mode

Setting night view LED

illumination mode

On/Off/Auto On

On/Off/Auto Auto

Ringing one time

Ring continuously

No ring-back tone

Alternate switching mode

Zoom mode

Full screen mode

Ringing one time

Alternate switching mode

-7-

SETUP INSTRUCTIONS

Setting Door Station Address

Total 4 addresses can be congured. It can be modied either before or after installation.

0 is default, to change the setting, please follow the steps:

ID=0,1st door station ID=1,2nd door station ID=2,3rd door station ID=3,4th door station

In standby mode, press KEY_SET button once

Press KEY_1 button to set the first door station.