NY Wholesale Intercom DT607FE-ID-S1, DT607FE-ID-S2, DT607FE-ID-S3, DT607FE-ID-S4 User Manual

DT-ENG-DT607-V1 / 201609

2 WIRE SYSTEM

DT607 Series

Fisheye door station with proximity access control

USER MANUAL

RF CARD

RF CARD

• Please read this manual carefully to ensure safe and correct operation.

• Keep this manual well for future reference.

RF CARD

RF CARD

DT607F/ID/FE-S4DT607/ID/FE-S3 DT607/ID/FE-S4

RF CARD

DT607A/ID-S4DT607/ID/FE-S1 DT607/ID/FE-S2

RF CARD

CONTENTS

PARTS AND FUNCTIONS ..................................................................................... 3

Part Names............................................................................................................. 3

Mounting ................................................................................................................. 4

BASIC FUNCTIONS .............................................................................................. 6

Unlock Operations .................................................................................................. 6

Fisheye Camera ..................................................................................................... 6

External Motion Detection ...................................................................................... 6

SETUP INSTRUCTIONS ........................................................................................ 7

Functions Setting Up .............................................................................................. 7

Setting Door Station Address .................................................................................8

Setting Camera Resolution..................................................................................... 9

Setting Unlock Mode .............................................................................................. 9

Setting Unlock Time............................................................................................... 10

Setting Nameplate Illumination Mode .................................................................... 10

Setting Night View LED Illumination Mode ............................................................ 11

Setting Ring-back Tone ......................................................................................... 11

Setting Image Display Mode.................................................................................. 12

Registering ID Card ............................................................................................... 13

WIRING ................................................................................................................. 16

Connecting Electric Lock ....................................................................................... 16

How to hook up a door release.............................................................................. 18

One apartment connection .................................................................................... 18

Two apartments connection...................................................................................19

Three apartments connection ................................................................................ 19

Four apartments connection .................................................................................. 20

Connecting Multi Door Stations ............................................................................. 20

APPENDIX ............................................................................................................ 21

Precautions............................................................................................................ 21

Specication .......................................................................................................... 21

Cables and Requirments ....................................................................................... 22

PARTS AND FUNCTIONS

Part Names

Surface mounted

[13]

Flush mounted

[11]

[12]

[11]

[12]

[10]

[1]

[9]

[8]

[7]

[6]

[5]

[14]

[9]

[8]

[2]

[3]

[4]

[1]

[2]

[3]

[13]

[1] Microphone

[2] UNLOCK indicator

[3] CALL indicator

[4] Call button

[5] Nameplate

[6] Front panel

[7] Speaker

[8] Night view LED

[9] Camera lens

[7]

[4]

[6]

[5]

[10] Rainy cover

[11] Mounting hook

[12] Connection port

[13] Screw hole

[14] Mounting box

-3-

PARTS AND FUNCTIONS

Mounting

The installation height is suggested to 145~160cm.

Surface mounted

1 2 3 4 5

The distance between

Main unit

the top of main unit
and rain cover should
be not less than 3mm.

Rainy cover

≥0.12 inch

Main unit

AcDbMLeader (ACDB_MLEADER_CLASS)

AcDbMLeader (ACDB_MLEADER_CLASS)

Rainy cover

1. Connect the cable correctly.

2. Drill holes in the wall to match the size of screw stoppers,then attach the rainy cover and
main unit to the wall,and the distance between the top of main unit and rain cover should be not

less than 0.12 inch.

3. Install the name plate.

4. Attach the front panel to the main unit.

5. Use the special screwdriver and the screws to x the panel.

Flush mounted

1 2 3 4 5

AcDbMLeader (ACDB_MLEADER_CLASS)

1. Drill a hole in the wall to match the size of mounting box,then attach the mounting box to the
wall.

2. Loosen the high screws to install the name plate.

3. Connect the cable correctly.

4. Attach the front panel to the mounting box,then use the special screwdriver and the screws to

x the panel.

5. Finish the installation.

* The camera angle view of surface mount model may be less than 1700.

-4-

AcDbMLeader (ACDB_MLEADER_CLASS)

AcDbMLeader (ACDB_MLEADER_CLASS)

PARTS AND FUNCTIONS

Terminal description

1 2 3

+12V

L2

L1

GND

PL

PIR

Lock Control Jumper

S-

S+

PIR Motion Detector
Connect Port

Main Connect Port

Lock Control Jumper:

Motion Detector Connect Port:

Main Connect Port:

L1,L2:

•

•

•

•

Connect to the bus line, no polarity.

PL:

External lock power input, connect to the power positive(power +).

S+:

Lock power(+) output.

S-:

Lock power(-) output, connect to the power(-) input of locks(only when using the door

To select the lock type.

To connect external PIR motion detector.

To connect the bus line and the electronic locks.

station to power the locks, if using the external power supply for the locks, the S- will not be
connected).

-5-

BASIC FUNCTIONS

detector

Unlock Operations

Unlocking of ID Card

When the registered user card has been shown to ID card window, the UNLOCK indicator lights

up, the buzzer sounds,and the electric door strike is unlocked.

• If show the authorized user card,the buzzer will sound of beep+,and the UNLOCK indicator
will light up.

• If show the unauthorized user card,the buzzer will sound of beep,beep,beep.

Fisheye Camera

Please note that this function requires the

monitor with sheye function to support.

The angle view is 1700,visitors in this angle

view can be seen clearly and can be zoomed

to see individuals up close via indoor monitor

with sheye function.

Standard

door station angle

DT607

1700 door camera angle

(Wide angle view shown)

External Motion Detection

The door station is equipped with a terminal to

connect external motion detector.

If the external motion detector is connected

to the system,following functions will be effec-

tive:

If detect someone passing by, the door station

can be activated operation to unlock or turn

on light.

* Please contact with supplier for more details about
detector connection.

-6-

12V

GND

PIR

Motion

SETUP INSTRUCTIONS

Functions Setting Up

This section explains the settings of each

function,please refer to the following table:

To perform the settings for the function

you want,you should move away the metal

front panel. Please refer to the sketch

map.

Each operation is indicated by the lighting

up of the

LED

indicator on the unit, and by

the sounding of the buzzer.

Order Setting items Setting range Default value

1 Setting door station address 0~3 0

2 Setting camera resolution High/Low High

LED_NAME

RF CARD

LED_UNLOCK

LED_TALK

KEY_SET
KEY_4

KEY_3

KEY_2

KEY_1

3 Setting the unlock mode 0:opened/1:closed 0:opened

4 Setting the unlock time 01 to 99 seconds 1 seconds

5

6

7 Setting ring-back tone

8 Setting image display mode

Setting the nameplate

illumination mode

Setting night view LED

illumination mode

On/Off/Auto On

On/Off/Auto Auto

Ringing one time

Ring continuously

No ring-back tone

Alternate switching mode

Zoom mode

Full screen mode

Ringing one time

Alternate switching mode

-7-

SETUP INSTRUCTIONS

Setting Door Station Address

Total 4 addresses can be congured. It can be modied either before or after installation.

0 is default, to change the setting, please follow the steps:

ID=0,1st door station ID=1,2nd door station ID=2,3rd door station ID=3,4th door station

In standby mode, press
KEY_SET button once

Press KEY_1 button to set
the first door station.

UNLOCK Indicator:OFF
TALK Indicator:OFF

Buzzer

Beep+

Press KEY_2 button to set
the second door station.

UNLOCK Indicator:OFF
TALK Indicator:OFF

Buzzer

Beep,Beep

UNLOCK Indicator:OFF
TALK Indicator:OFF

Press KEY_3 button to set
the third door station.

UNLOCK Indicator:OFF
TALK Indicator:OFF

Buzzer

Beep,Beep,Beep

Buzzer

Beep+, Beep

Press KEY_4 button to set
the fourth door station.

UNLOCK Indicator:OFF
TALK Indicator:OFF

Buzzer

Beep,Beep,Beep,Beep

• If setting mode has not been exited, you can change the address of door station by pressing KEY1~4
freely.

LED_NAME

• The

indicator will always blink until exit out the setting mode.

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• In this step,press

KEY_SET

button four times to exit out the setting mode manually.

-8-

SETUP INSTRUCTIONS

Setting Camera Resolution

The resolution of the camera can be adjusted at any time, that means the quality of image on

screen can be set to high or low.

High resolution is default, to change the setting, please follow the steps:

In standby mode, press
KEY_SET button twice.

UNLOCK Indicator:OFF
TALK Indicator:ON

Buzzer

Beep+, Beep

Press KEY_2 button to set the
camera to High resolution.

UNLOCK Indicator:OFF
TALK Indicator:ON

Buzzer

Beep+

Press KEY_2 button again
to set the camera to Low
resolution.

UNLOCK Indicator:OFF
TALK Indicator:ON

Buzzer

Press KEY_2

Beep, Beep

• If setting mode has not been exited, you can change the camera resolution by pressing KEY2 circularly.

LED_NAME

• The

indicator will blink all the time until exit out the setting mode.

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• In this step,press

KEY_SET

button three times to exit out the setting mode manually.

Setting Unlock Mode

There are 2 unlock modes,

Normally opened

Normally opened is default, to change the setting, please follow the steps:

In standby mode, press

KEY_SET button three
times.

UNLOCK Indicator:ON
TALK Indicator:OFF

Press KEY_1 button to set
the unlock mode to
Normally opened.

UNLOCK Indicator:ON
TALK Indicator:OFF

Normally closed

and

Press KEY_1 button again
to set the unlock mode to
Normally closed.

UNLOCK Indicator:ON
TALK Indicator:OFF

.

Buzzer

Beep+, Beep

Buzzer

Beep+

Press KEY_1

Buzzer

Beep, Beep

• If setting mode has not been exited, you can change the unlock mode by pressing KEY1 circularly.

LED_NAME

• The

indicator will blink all the time until exit out the setting mode.

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• In this step,press

KEY_SET

button twice to exit out the setting mode manually.

-9-

SETUP INSTRUCTIONS

Setting Unlock Time

By default, the unlock time is 5 seconds, but it can be changed,the setting range is 1s~99s.

Follow the steps:

In standby mode, press

KEY_SET button three
times.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep+, Beep

Press and hold on KEY_2
button. The time you holding
on is the new unlock time.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep,Beep......

• When entering time delayed setting, the buzzer sound one time every second.

LED_NAME

• The

indicator will blink all the time until exit out the setting mode.

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• In this step,press

KEY_SET

button twice to exit out the setting mode manually.

Setting Nameplate Illumination Mode

There are 3 illumination modes for nameplate indicator,

Normally on is default, to change the setting, please follow the steps:

In standby mode, press

KEY_SET button three
times.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep+, Beep

Press KEY_3 button to set
the nameplate illumination
mode to Normally on.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep+

Normally on,Normally off

Press KEY_3 button again
to set the nameplate illumina­tion mode to Normally off.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep, Beep

Auto

and

Press KEY_3 button again
and again to set the nameplate
illumination mode to Auto.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep, Beep,Beep

.

Press KEY_3

• If setting mode has not been exited, you can change the nameplate illumination mode by pressing KEY3

circularly.

LED_NAME

• The

indicator will blink all the time until exit out the setting mode.

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• In this step,press

KEY_SET

button twice to exit out the setting mode manually.

-10-

SETUP INSTRUCTIONS

Setting Night View LED Illumination Mode

There are 3 working modes for night view LED indicator,

Normally on,Normally off

and

Auto

.

Auto is default, to change the setting, please follow the steps:

In standby mode, press

KEY_SET button three
times.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep+, Beep

• If setting mode has not been exited, you can change the night view LED illumination mode by pressing

KEY4 circularly.

LED_NAME

• The

indicator will blink all the time until exit out the setting mode.

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• In this step,press

KEY_SET

Press KEY_4 button to set
the night view LED mode
to Normally on.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep+

Press KEY_4 button again
to set the night view LED
mode to Normally off.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep, Beep

Press KEY_4

button twice to exit out the setting mode manually.

Press KEY_4 button again
and again to set the night
view LED mode to Auto.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep, Beep,Beep

Setting Ring-back Tone

If allow ring-back tone, press the call button to call monitor, a ring-back call tone can be heard

from door station.

There are 3 ring-back call tones,

tone

.

Ringing one time,Ringing continuously

Ringing one time is default, to change the setting, please follow the steps:

No ring-back

and

In standby mode, press

KEY_SET button four
times.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep+, Beep

Press KEY_1 button to set
the ring-back call tone ringing
one time.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep+

Press KEY_1 button again
to set the ring-back call tone
ringing continuously.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep, Beep

Press KEY_1

Press KEY_1 button again
and again to close ring-back
call tone.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep, Beep,Beep

• If setting mode has not been exited, you can change the ring-back tone by pressing KEY1 circularly.

LED_NAME

• The

indicator will blink all the time until exit out the setting mode.

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• In this step,press

KEY_SET

button once to exit out the setting mode manually.

-11-

SETUP INSTRUCTIONS

Setting Image Display Mode

Please know that this setting is only effective for monitors which does not support man-

ual operation for pan-tilt.

When the monitor being called

When door station calls monitor,the image will be displayed on screen,there are 3 modes for im-

age displayed,

Alternate switching mode:

Full screen

Zoom mode:

seconds, then switch to

Full screen mode:

screen

Alternate switching mode,Zoom mode

when the monitor being called, switch at regular time(5s) between

Zoom

and

image.

when the monitor being called, the image will be displayed on full screen for 5

Zoom

image.

when the monitor being called, the image will be always displayed on

.

Alternate switching mode is default, to change the setting, please follow the steps:

Full screen mode

and

.

Full

In standby mode, press

KEY_SET button four
times.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep+, Beep

Press KEY_2 button to set
the image display mode
to Cycle switching.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep+

Press KEY_2 button again
to set the image display
mode to Zoom mode.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep, Beep

Press KEY_2

Press KEY_2 button again
and again to set the image
display mode to Full screen.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep, Beep,Beep

• If setting mode has not been exited, you can change the image display mode by pressing KEY2 circularly.

LED_NAME

• The

indicator will blink all the time until exit out the setting mode.

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• In this step,press

KEY_SET

button once to exit out the setting mode manually.

When answering the call

When answering the call, the image switching reminder can be activated or forbidden.

If set to activated mode, the image switching reminder will be different for different image display

mode.

Alternate switching mode:

Zoom mode:

When answering the call, the image will be displayed on

onds, then switch to

When answering the call, image switching reminder is not effective.

full screen

Zoom

image to remind to enter talking status.

for 5 sec-

-12-

SETUP INSTRUCTIONS

Full screen mode:

When answering the call, the image will be displayed on

seconds, then switch to

Full screen

to remind to enter talking status.

Zoom

mode for 5

If set to forbidden mode, there is no image switching reminder at any image display mode.

Activated is default, to change the setting, please follow the steps:

In standby mode, press

KEY_SET button four
times.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep+, Beep

• If setting mode has not been exited, you can change the image display mode by pressing KEY3 circularly.

LED_NAME

• The

indicator will blink all the time until exit out the setting mode.

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• In this step,press

KEY_SET

Press KEY_3 button to
activate image switching
when answering the call.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep+

Press KEY_3 button again
to forbid image switching
when answering the call.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Press KEY_3

Beep, Beep

button once to exit out the setting mode manually.

Registering ID Card

• Up to 320 user cards can be registered by the door station.

• Easy management with LED status and sound hints.

• There are two master cards, one

and one

MASTER CARD DELETE

master cards, the old master cards are invalid automatically.

• Card reading distance is less than 3cm.

• The master cards are necessary when you add or delete user

cards. Please keep it well for future use.

• EM card, 125kHz.

MASTER CARD ADD

card

card, When registered new

Authorizing master cards:

By default,there are two master cards marked

DELETE

,but you should know that the master card can be authorized by users at any time.

MASTER CARD ADD

That means any two user cards can be authorized to master cards,When registered new master

cards, the old master cards will be invalid automatically.

MASTER CARD

and

-13-

SETUP INSTRUCTIONS

When power on in 10s,press
and hold on KEY_SET button
for 3s.

UNLOCK Indicator:OFF
TALK Indicator:OFF

Buzzer

Beep+, Beep

LED_NAME

• The

Press KEY_2 button.

UNLOCK Indicator:Blink one time
TALK Indicator:OFF

Buzzer

Beep+

Show the first card to ID
card window, set the card
of MASTER CARD ADD.

UNLOCK Indicator:Blink two times
TALK Indicator:OFF

Buzzer

Beep,Beep

indicator will always blink until exit out the master card authorized mode.

Show the second card to ID
card window, set the card of
MASTER CARD DELETE.

UNLOCK Indicator:Blink three times
TALK Indicator:OFF

Buzzer

Beep,Beep,Beep

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• It will exit out setting mode automatically after showing these two cards,the UNLOCK&TALK indicator will be

turned off.

Switching Access Control:

The access can be controlled by door station or DT-ACC,so it’s available to switch the access

function.

Show the master card of
MASTER CARD DELETE
again to switch as a door
station access control.

UNLOCK Indicator:OFF

Show the master card of
MASTER CARD ADD to ID
card window in standby.

UNLOCK Indicator:OFF
TALK Indicator:ON

Buzzer

Beep+, Beep

Show the master card of
MASTER CARD DELETE
to ID card window.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep+, Beep

TALK Indicator:OFF

Buzzer

Beep+

Show the master card of
MASTER CARD DELETE
again to switch to DT-ACC
controlled.

UNLOCK Indicator:OFF
TALK Indicator:OFF

Buzzer

Beep+,Beep

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• If current access is controlled by door station, next access switching setting is controlled by DT-ACC.

-14-

SETUP INSTRUCTIONS

Adding User Cards:

Show the master card of
MASTER CARD ADD to ID
card window in standby.

UNLOCK Indicator:OFF
TALK Indicator:ON

Buzzer

Beep+, Beep

Show user cards to be
added in sequence.

UNLOCK Indicator:OFF
TALK Indicator:Blink one time

Buzzer

Beep+

Show the master card of
MASTER CARD ADD again
to exit.

UNLOCK Indicator:OFF
TALK Indicator:OFF

Buzzer

Beep, Beep+

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• To add user card, the access must be controlled by door station.

Deleting User Cards:

Show the master card of
MASTER CARD DELETE to
ID card window in standby.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep+, Beep

• .If without any operation in 10 seconds, it will exit out setting mode automatically.

• To add user card, the access must be controlled by door station.

Show user cards to be
deleted in sequence.

UNLOCK Indicator:Blink one time
TALK Indicator:OFF

Buzzer

Beep+

Show the master card of
MASTER CARD DELETE
again to exit.

UNLOCK Indicator:OFF
TALK Indicator:OFF

Buzzer

Beep, Beep+

Initializing Access (delete all user cards):

Show the master card of
MASTER CARD DELETE to
ID card window in standby.

UNLOCK Indicator:ON
TALK Indicator:OFF

Buzzer

Beep+, Beep

Show the master card of
MASTER CARD ADD to ID
card window.

UNLOCK Indicator:ON
TALK Indicator:ON

Buzzer

Beep+, Beep

• If without any operation in 10 seconds, it will exit out setting mode automatically.

• To add user card, the access must be controlled by door station.

• At step3, the UNLOCK & TALK indicator will blink all time until formatting is nished.

• When formatting is nished, UNLOCK & TALK indicator will be turned off and sound “ Beep+ ”, and exit out

setting mode automatically.

Show the master card of
MASTER CARD ADD again,
format is activated.

UNLOCK Indicator:Blink for some time
TALK Indicator:Blink for some time

Buzzer

Beep

-15-

WIRING

Connecting Electric Lock

(NOT RECOMMENDED). See Next page.

Note: NOT RECOMMENDED unless the door lock is less than 250mA. Please see Next page

for HOW TO HOOK UP A DOOR RELEASE.

Door Lock Controlled with Internal Power

1.Electronic lock of Power-on-to-unlock

type should be used.

2.The door lock is limited to 12V, and hold-

ing current must be less than 250mA.

3.The jumper should be placed on position

2 and 3 before connecting.

4.The door lock control is not timed from

Exit Button(EB).

5.The

Unlock Mode

must be set to 0 (by

default).

1 2 3

Jumper position on 2&3

L1 L2 PL S+ S-

*

EB

LOCK

Door Lock Controlled with Dry Contact

1.The external power supply must be used

according to the lock.

2.The inside relay contact is restricted to

230Vac 1A or 24Vdc 1A.

3.The jumper must be taken off before

connecting.

4.Setup the

Unlock Mode

according to

different lock types.

• Power-on-to-unlock type:Unlock
Mode=0 (by default)

• Power-off-to-unlock type:Unlock
Mode=1

* DT-RLC relay actuator is needed for 2nd lock connection.

-16-

1 2 3

Take off the jumper

L1 L2 PL S+ S-

POWER
SUPPLY

LOCK

WIRING

How to hook up a door release

Door Station

DT607

L1 L2 PL S+ S-

X XINX X

A/C or D/C

Power Supply

+ -

OUT

Model: DS-ERL

Note: Relay is NOT SENSITIVE to POLARITY.
For Magnetic Locks you will need a ELK-1 Relay.

Door Station

DT607

Power
Supply

L1 L2 PL S+ S-

+ -

-

+

- + N/O COM N/C
Magnetic Lock

ELK1 Relay

For A/C or D/C door
releases HINTS.
Match the door release
Input Voltage to power
source.

Power Door
Release
A/C = A/C
D/C = D/C
12vDC = 12vDC
24vDC = 24vDC

16vA/C = ∞16vA/C

∞

S
T
R
I
K
E

Power Supply can be A/C or
D/C as long as it matches the
needs of the magnetic lock.

By hooking up the ELK1 to the
door release this saves the
outdoor station from being
damaged which is NOT
covered by the warranty!

The reason for this is that all
Magnetic Locks have more
than 200mA and the panel
relay Max is 200m

A.

Note: Bus (L1, L2) to DT-DPS or DBC4A1 if you
have more than 1 door station.

-17-

WIRING

Notes:

[1] For DT607 One button, the code address of indoor units start at 0-15 (switch all DOWN).

[2] For DT607 Two buttons, the code address of indoor units start at 16-31 (switch 5 ON).

[3] For DT607 Three buttons, the code address of indoor units are range from 1-3.

[4] For DT607 Four buttons, the code address of indoor units are range from 1-4.

[5] When use IN-OUT wiring without any distributor, Switch 6 ON for last monitor on the line.

When use Star wiring with distributor, Switch 6 ON for every monitor.

One Apartment Connection

ID=0

Code=00, DIP6=on

-

+

RF CARD

L1 L2 PL S+ S-

-

+

DPSDR-30-24

L1

L2

DIP Switches

ON DIP

1 2 3 4 5 6

-18-

ID=0

RF CARD

L1 L2 PL S+ S-

Code=01, DIP6=on

L1

L2

DIP Switches

ON DIP

1 2 3 4 5 6

Code=00, DIP6=off

-

+

DPSDR-30-24

L1

L2

DIP Switches

ON DIP

-

+

1 2 3 4 5 6

WIRING

Two Apartments Connection

ID=0

RF CARD

L1 L2 PL S+ S-

-

+

Three Apartments Connection

Code=16, DIP6=on

L1

L2

DIP Switches

ON DIP

1 2 3 4 5 6

Code=00, DIP6=off

-

+

DPSDR-30-24

L1

L2

DIP Switches

ON DIP

1 2 3 4 5 6

Code=01, DIP6=on

L1

L2

DIP Switches

ON DIP

1 2 3 4 5 6

ID=0

RF CARD

L1 L2 PL S+ S-

-

+

Code=02, DIP6=on

L1

L2

DIP Switches

ON DIP

1 2 3 4 5 6

Code=03, DIP6=on

L1

L2

-

+

A B C D

DPSDR-30-24

DIP Switches

ON DIP

1 2 3 4 5 6

DBC4A1

Impedance

switch

OFF

ON

-19-

WIRING

Four Apartments Connection

Code=01, DIP6=on

L1

L2

DIP Switches

ON DIP

1 2 3 4 5 6

Code=02, DIP6=on

L1

L2

DIP Switches

ON DIP

1 2 3 4 5 6

Code=03, DIP6=on

ID=0

RF CARD

L1 L2 PL S+ S-

-

+

Connecting Multi Door Stations

st

Monitors

door station

1

ID=0

RF CARD RF CARD RF CARD RF CARD

2nd door station

ID=1

Code=04, DIP6=on

L1

L2

DIP Switches

ON DIP

1 2 3 4 5 6

-

+

3rd door station

DPSDR-30-24

ID=2

L1

L2

A B C D

DBC4A1

DIP Switches

ON DIP

1 2 3 4 5 6

Impedance

switch

OFF

ON

4th door station

ID=3

L1 L2 PL S+ S- L1 L2 PL S+ S- L1 L2 PL S+ S- L1 L2 PL S+ S-

-

Impedance

switch

A B C D

OFF

DBC4A1

ON

+

DPSDR-30-24

• Max.4 door stations can be connected to the system.

• Ensure to set the correct address for each door station, Refer to Page 8 for more details

about the address setting of door stations.

-20-

APPENDIX

Precautions

• Please clean the unit with soft cotton cloth, don't use the organic impregnant or chemical
clean agent. If necessary, please use a little pure water or dilute soap water to clean the dust.

• The unit is weather resistant. However do not spray high pressure water on access control
keypad directly. Excessive moisture may cause problems with the unit.

• You must use the right adaptor which is supplied by the manufacture or approved by the
manufacture.

• Pay attention to the high voltage inside the products, please refer service only to a trained
and qualied professional.

Specification

Power supply: DC 24V

Power consumption: Standby 0.8W; Working 3W

Camera lens: Color CMOS, 2.0 Mega pixel

1/2.7’’ sheye camera,1700 wide angle

Lock Power supply: 12Vdc, 280mA(Internal Power);

Number of relay circuits: 2(the second lock need external device to support)

Mounting: Surface wall-mount / ush mount

Working temperature: -20ºC ~ +55ºC

Protection: IP54

Material: Zinc alloy panel(surface mounted)

Stainless steel panel(ush mounted)

Wiring: 2 wires, non-polarity

Dimension: 6.93(H)×3.54(W)×1.06(D)inch(surface mounted)

8.66(H)×4.69(W)×2.05(D)inch(ush mounted)

-21-

APPENDIX

Cables and Requirments

The maximum distance of the wiring is limited in the DT system. Using different cables may also

affect the maximum distance which the system can reach.

Basic IN-OUT Wiring Mode

B

-22-

When Monitor quantity < 20

Cable Usage A B

Twisted cable 2x0.00116 sq.in 196ft 196ft

-

+

DPSDR-30-24

Twisted cable 2x0.00155 sq.in 262ft 262ft

When Monitor quantity > 20

Cable Usage A B

A

Twisted cable 2x0.00155 sq.in 229ft 98ft

Twisted cable 2x0.00233 sq.in 229ft 164ft

Note: The thicker the copper wire is, the longer

RF CARD

distances will be. Best wire to use is 18 Gauge
twisted, while Cat 5 or 6 are not recommended.

APPENDIX

Star Topology Wiring Mode With DBC4A1

2

DBC4A1

B

2

C

When Monitor quantity < 20

-

+

DPSDR-30-24

Cable Usage A B C

Twisted cable 2x0.00116 sq.in 196ft 196ft 98ft

Twisted cable 2x0.00155 sq.in 262ft 262ft 131ft

A

When Monitor quantity > 20

Cable Usage A B C

Twisted cable 2x0.00155 sq.in 229ft 98ft 65ft

RF CARD

Twisted cable 2x0.00233 sq.in 229ft 164ft 98ft

Note: The thicker the copper wire is, the longer
distances will be. Best wire to use is 18 Gauge
twisted, while Cat 5 or 6 are not recommended.

-23-

FOR TECHNICAL SUPPORT CALL

1516-387-6606 FROM 9AM TILL 4PM

MONDAY THRU FRIDAY

OUR WEBSITE WWW.NYWINT.COM

DT-ENG-DT607-V1

The design and specications can be changed without notice to the user. Right to interpret and copyright of this
manual are preserved.