NYNE Aqua User Manual
nyne.com
Make sure that the speaker is in pairing mode.
1
Enable Bluetooth on your device to
Aqua
CS
Přenosného reproduktoru
Bluetooth
ET
Kaasaskantav Bluetooth kõlar
GE
für einen portablen
Bluetooth-Lautsprecher
HU
Rövidített használati útmutató
LV
Pārnēsājams Bluetooth
skaļrunis
LT
Garsiakalbio vartotojo vadovas
PL
Przenośnego głośnika
Bluetooth
RO
Difuzor portabil Bluetooth
SK
Prenosného
reproduktoraBluetooth
2
1
NYNE AQUA
Press and hold until the Bluetooth
indicator ashes blue.
CS
Stručná příručka uživatele
ET
Lühike kasutusjuhend
GE
verkürztes Benutzerhandbuch
HU
Hordozható Bluetooth
hangszóró
LV
Saīsināta Lietotāja
Rokasgrāmata
NYNE Aqua_Quick User Guide_20140623.indd 1-6 2014/6/23 20:10:46
LT
Sutrumpintas nešiojamojo
bluetooth
PL
Skrócony Przewodnik
Użytkownika
RO
Ghid de referinţă rapidă
SK
Stručná príručka užívateľa
Charge the speaker until the red
power indicator turns off.
If the power indicator ashes red
Tip:
quickly, it indicates that the battery
is low and needs to be recharged.
For rst-time use, the Bluetooth indicator
+
ashes blue quickly, indicating that
the speaker is in pairing mode.
When you power on the speaker
Tip:
again after Bluetooth setup, the speaker
will search for the paired device and the
Bluetooth indicator will ash slowly. If no
paired device is found, it will ash quickly
and the speaker will enter pairing mode.
2
be paired with the speaker.
Select ‘NYNE AQUA’ from the available devices
3
(enter the password ‘0000’ if necessary) to start
pairing and connection with the speaker.
After successful connection, the Bluetooth
4
indicator turns solid blue and the speaker beeps.
This speaker supports automatic
Tip:
connection with a previously paired device
after power-off and power-on again.
You can press and hold for more
than 2 seconds to enter manual pairing
mode. In this way, you can pair the
speaker with a new Bluetooth device.
You can press and hold both +/- for more than
5 seconds to clear all paired Bluetooth devices.
This speaker is compatible with the voice
assistant on your smart device.
QUG-Aqua-06-23-2014-V1.0
All rights reserved.
Play music on your device paired
and connected with the speaker.
Nyne Multimedia Inc.
property of their respective owners.
All registered and unregistered trademarks are
During music play:
•
Press
•
Press and hold
the previous or next song.
•
Press to pause or resume music play.
Press to select your favorite preset
•
sound effect: FLAT, ROCK, POP or JAZZ.
Press and hold for more than 3
•
seconds to return to FLAT at any time.
+
+
NYNE Aqua_Quick User Guide_20140623.indd 7-12 2014/6/23 20:10:50
This speaker supports automatic
Note:
connection with a previously paired device
after power-off and power-on again.
to adjust volume.
+/-
to skip to
+/-
The Bluetooth indicator ashes
blue once when you select a
sound effect other than FLAT.
The Bluetooth indicator ashes blue
twice when you select FLAT.
When you make a call or there is
an incoming call, you can use the
speaker as a speaker phone.
When there is an incoming call, you
•
can press to receive the call or
press twice to reject the call.
•
During a call, you can press to end the call.
•
In BT mode, you can press twice to access
the voice assistant on your smart device. To
exit the voice assistant, press twice again.
Music play is paused during a call and
Tips:
resumed automatically when the call ends.
You can press and hold to disconnect
the current Bluetooth connection.
If no source is detected, the
button does not function.
Connect an auxiliary audio
1
device to the speaker through the
supplied 3.5mm audio cable.
Play and control music on the audio
2
device, and use
to adjust volume if necessary.
In AUX IN mode, you can press
Tips:
to mute sound output from the speaker.
2
1
When the 3.5mm audio cable is plugged
in, the speaker switches to AUX IN mode
automatically. When it is unplugged, the
speaker switches back to Bluetooth mode.
The button also functions in AUX IN mode.
The voice assistant function does
not work in AUX IN mode.
In case of abnormality, you can hold
the RESET button to reset the speaker.
on the speaker
+/-
Loading...