NXP Semiconductors NXQ1TXH5DB1355, NXQ1TXH5DB1401, NXQ1TXH5 User Manual
UM11152
NXQ1TXH5DB1355 plugin board
Rev. 1 — 6 December 2018 User manual
Document information
Information Content
Keywords NXQ1TXH5DB1355, NXQ1TXH5DB1401, NXQ1TXH5, plugin board, LPC824
Abstract This manual describes how to use the NXQ1TXH5DB1355 board in
combination with a NXQ1TXH5 design. The document describes how to
connect the NXQ1TXH5DB1355 board to a PC and the NXQ1TXH5. This
enables engineers to verify operation of the NXQ1TXH5 in a customer
specific design. This eases the design of a wireless power transmitter using
the NXQ1TXH5.
NXP Semiconductors
UM11152
NXQ1TXH5DB1355 plugin board
UM11152 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2018. All rights reserved.
User manual Rev. 1 — 6 December 2018
2 / 15
Revision history
Rev Date Description
v.1 20181206 first issue
NXP Semiconductors
UM11152
NXQ1TXH5DB1355 plugin board
UM11152 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2018. All rights reserved.
User manual Rev. 1 — 6 December 2018
3 / 15
1 Introduction
This document describes how to use the NXQ1TXH5DB1355 plugin board.
The NXQ1TXH5DB1355 board can be used in combination with the NXQ1TXH5DB1401
demo board or with a customer-specific design. The NXQ1TXH5DB1355 plugin board
contains a microcontroller, the LPC824M201JDH20. This microcontroller interfaces
between the I2C from the NXQ1TXH5 and the UART.
The NXQ1TXH5DB1355 can be used for the following tasks:
• Read out Qi operating phase (ping, power transfer, foreign object detected, fault state)
• Verifying parameter setup via configuration resistors
• Read out chip temperature, switching frequency
• Foreign power calibration
This information helps designers with the verification and testing of their NXQ1TXH5
application.
NXP Semiconductors
UM11152
NXQ1TXH5DB1355 plugin board
UM11152 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2018. All rights reserved.
User manual Rev. 1 — 6 December 2018
4 / 15
2 NXQ1TXH5DB1355 board connections
Figure 1. NXQ1TXH5DB1355 board connections
The NXQ1TXH5DB1355 board as shown in Figure 1 can be used in combination with the
TTL-232R- 3V3 cable from FTDI.
Table 1 shows the pinout of the connector on the FTDI cable. The NXQ1TXH5DB1355
board only uses GND, TXD, and RXD. The FTDI cable connects to header X4 of the
NXQ1TXH5DB1355 board.
Table 1. Pinout connector FTDI cable
Pin number Name Color Description
1 GND black device ground supply pin
2 CTS# brown clear to send control input/handshake signal
3 VCC red +5 V output
4 TXD orange transmit asynchronous data output
5 RXD yellow receive asynchronous data input
6 RTS# green receive to send control output/handshake signal
The NXQ1TXH5DB1355 is connected to the I2C interface of the NXQ1TXH5. The pullup resistors for the SDA and SCL lines are already on the NXQ1TXH5DB1355 board.
Connect the SDA, SCL, and GND pins of header X3 to the design with the NXQ1TXH5.
To power the components on the NXQ1TXH5DB1355 board, connect a 5 V supply to pin
9 and its GND connection. This supply can be obtained from a separate lab supply or
from the NXQ1TXH5 application.
NXP Semiconductors
UM11152
NXQ1TXH5DB1355 plugin board
UM11152 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2018. All rights reserved.
User manual Rev. 1 — 6 December 2018
5 / 15
Table 2. Header X3 point
Pin number Name Description
1 GND device ground supply pin
2 DATA_S not used
3 GND device ground supply pin
4 WS not used
5 GND device ground supply pin
6 BCK not used
7 SDA serial data
8 SCL serial clock
9 +5V device 5 V supply pin
10 +5V device 5 V supply pin
Loading...