NXG Technology NX-PRO6000 User Manual

NX-PRO4000, NX-PRO5000, & NX-PRO6000

OWNER’S

WEATHER-RESISTANT SPEAKER SYSTEM

Unpacking

Carefully remove your new NXG speakers from the box. Inspect the speakers for transit
damage. If you discover damage, contact your dealer immediately. Save your carton — it is
the best possible protection for your speakers should you ever have a need to move them.

Positioning and Mounting Your New NXG Speakers

Note: the distance between yourself and the point directly between the speakers should be
(roughly 20%) greater than the distance between the two speakers. Outside placement
may be different, due to variances in available mounting areas.

All NXG weather-resistant speakers are equipped with powder-coated ratcheting aluminum
mounting brackets that allow for vertical or horizontal mounting. Be certain the type of
anchor you choose, and the material you are mounting the anchor into, are capable of
holding the weight of the speaker. (Many mounting anchor systems are available from
your local hardware store.) After mounting the bracket, connect the wire as shown in
Figure 2, and loosely secure the speaker to the bracket using the supplied knobs. Adjust
the speaker’s angle for optimum listening area coverage and firmly hand-tighten the knobs.

MANUAL

Hooking Up Your
New NXG Speakers

STOP! – Make sure that you consult your amplifier’s
owner’s manual regarding speaker hook-up. Your am­plifier should be turned off throughout this procedure.

Most speaker wire is polarity coded. This means that
each conductor is labeled either (+) positive or (-)
negative. The (+) positive side may be a different
color or texture than the (-) negative side. On the
back of your amplifier, each channel should be
labeled (+) and (-) as well as color coded red for
(+) positive and black for (-) negative. NXG speaker
terminals are color coded red for (+) positive and
black for (-) negative. Be sure to hook (+) to (+), (red
to red), and (-) to (-), (black to black). (See figure 3.)
All connections should be tight. Inspect connections
for frays and stray strands of wire touching both (+)
and (-) terminals. (This will cause a short and, per­haps, damage your equipment.)

FIGURE 1

Speaker wire hole

Powder-coated

aluminum ratcheting

mounting bracket

Bracket knob

Brass inser
universal style
mounting hardware
(not included).

ts accept

CORRECT IN-PHASE HOOK-UP

Negative (Black)

Input Binding Post

o Negative T

T

er

of Amplifier

minal

Positive (Red)

Input Binding Post

To Positive Terminal

of Amplifier

FIGURE 2

Caring for Your Speakers

In outdoor applications, we recommend angling the
speakers downwar
exposure to precipitation and hot sun. If added pro­tection is desir
other shelter. DO NOT immerse the speakers in
water or subject them to direct water pressure.
During winter months, we r
speakers indoors if you are not using them.

d as shown in Figur

ed, mount speakers under eaves or

ecommend storing the

e 1 to reduce

BACK VIEW

TO CLEAN: All NXG weather-resistant enclosures can
be cleaned with a damp soft cloth and a mild deter­gent. The aluminum grille can also be cleaned with
the same cloth.

Specifications

MODEL NX-PRO4000 MODEL NX-PRO5000 MODEL NX-PRO6000

4˝ 2-way Indoor/Outdoor Speaker System 5.25˝ 2-way Indoor/Outdoor Speaker System 6.5˝ 2-way Indoor/Outdoor Speaker System

Cabinet: All three models are made of weather-resistant, UV treated, high-impact ABS composite to resist sun-fade and long-term exposure to the elements.

Tweeter:

oofer:

W

Frequency Response: 75 Hz-20,000 Hz 65 Hz - 20,000 Hz 55 Hz -20,000 Hz

Impedance: 8 ohms nominal 8 ohms nominal 8 ohms nominal

Power Handling: 5 to 75 watts 5 to 100 watts 5 to 125 watts

Efficiency: 87dB 89 dB 90dB

Speaker Dimensions: 911/16˝ H x 61/2˝ W x 6˝ D 103/4˝ H x 613/16˝ Wx 65/8˝ D 127/8˝ H x 8˝ W x 71/4˝ D

Weight Each: 5 lbs. 5.5 lbs. 7 lbs.

3

/4˝ (19mm) ultra-wide dispersion

metallic anodized dome metallic anodized dome metallic anodized dome

4˝ (102mm) injection-molded 5.25˝ (133mm) injection-molded 6.5˝ (165mm) injection-molded

metallic anodized cone w/rubber surround metallic anodized cone w/rubber surround metallic anodized cone w/rubber surround

3

/4˝ (19mm) ultra-wide dispersion 1˝ (25.4mm) ultra-wide dispersion

Troubleshooting and Service

The NXG speaker is equipped with a tweeter protec­tion device. If extreme power levels are reached, it
will reduce the amount of power going into the
tweeter. If you detect reduced output levels from the
speaker while playing at a high volume, it is a warn­ing that too much power is being applied. You must
reduce the level by turning down the volume of your
receiver to a safe level or permanent speaker dam­age may result. It is important to remember that no
amount of protection will prevent damage caused by
defective equipment or extreme abuse.

If you should have a pr
if it is indeed a speaker problem. Determine whether
the problem exists in both speakers. If it does, the
problem most likely originates in some other com­ponents in the system. If the pr
speaker only, reverse your speaker leads (left to
right, right to left). If the pr
speaker, your problem is not in the speakers.

Once you have determined that you have a speaker

oblem, contact your dealer for authorized factor

pr
service information. If you are unable to contact your
dealer, if your dealer is unable to solve your problem,
or if you have any questions or comments r
your NXG Speaker System, please contact us at the
address or phone number below.

16648 North 94th Street • Scottsdale, AZ

oblem, first try to determine

oblem is in one

oblem moves to the other

1-800-733-0008

egar

85260

y

ding

NXG Speaker Systems are designed to the highest possible value and performance standards.
Our confidence in their quality is such that NXG Technology offers customers this transferable
limited warranty:

NXG Speaker System Two-Year Limited Warranty

If the NXG speaker system proves to be defective in workmanship or materials within two years
from the date of the original customer’s purchase, we will, at our option, repair or replace the
defective product.

DISCLAIMER

THE WARRANTY STATED HEREIN IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING MERCHANTABILITY AND FITNESS FOR P
BILITIES AND OBLIGA
NXG

TECHNOLOGY HAS NOT MADE AND DOES NOT HEREBY MAKE ANY OTHER REPRESENTATION,
WARRANTY OR COVENANT WITH RESPECT TO THE CONDITION, QUALITY, DURABILITY, DESIGN,
OPERATION, CAPACITY, FITNESS FOR USE OR SUITABILITY OF THE NXG SPEAKER SYSTEMS.

TIONS OF NXG TECHNOLOGY

TICULAR PURPOSE AND ALL OTHER LIA-

AR

, ALL OF WHICH ARE EXPRESSL

Y DISCLAIMED.

Exclusion of Certain Damages

echnology’s liability for any defective product is limited to repair or replacement of pro-

NXG T
duct at our option. NXG T
of any kind or character because of product defects. Some states do not allow limitations on
how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitations and exclusions may not apply.

echnology shall not be liable for incidental or consequential damages

This Warranty Does Not Cover:

• Damage caused by abuse, accident, misuse, negligence, or impr

• Any product whose serial number has been altered, defaced, or removed.

• Products that have been altered or modified.

mal wear and maintenance.

• Nor

• Damages caused by shipping. (All claims for shipping damage must be made with the carrier.)

oper operation.

Warranty Service

Warranty service must be performed by an authorized service center, usually an NXG speaker
systems dealer or its authorized agent. All warranty repairs must be accompanied by the original
bill of sales. No other document is acceptable or is r
rights, and you may also have other rights which vary from state to state.

NXG reserves the right to revise speaker system specifications without notice.

equir

ed. This war

ranty gives you specific legal