CAUTION: DO NOT EXCEED MAXIMUM LISTED
CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE
MAY OCCUR!
Small Full Motion Mount
Max Screen Size: 32”
Max weight: 35lbs
P1
Congratulations on the purchase of your new TV Mount. At NXG
Technology we design our products to be simple to use, durable, &
furnctional.
Like all NXG products, our mount line has evolved from hours of
rigorous testing by our engineers and customers and were
designed to provide you with years of enjoyment.
Please take a moment to review the installation instructions to
ensure that you get the most from your new mount.
support@nxgtechnology.com
DISCLAIMER – WARNING INFORMATION
Disclaimer – NXG™ has extended every effort to ensure to accuracy and completeness of this manual. However, NXG does not claim that the information
covers all installation and or operational variables. The information contained in this document is subject to change without notice or obligation of any kind.
Regarding the information contained herein, NXG makes no representation of warranty, expressed or implied, and assumes no responsibility for accuracy,
sufficiency, or completeness of the information contained in this document.
WARNING: FAILURE TO READ, THOROUGHLY UNDERSTAND, AND FOLLOW ALL INSTRUCTIONS CAN RESULT IN SERIOUS PERSONAL INJURY,
DAMAGE TO PERSONAL PROPERTY, OR VOIDING OF FACTORY WARRANTY!
It is the responsibility of the installer to ensure all components are properly assembled and installed using the instructions provided. If you do not understand these
instructions or have any questions or concerns, please send questions to support@nxgtechnology.com.
Do not attempt to install or assemble this product if the product or hardware is damaged or missing. The included hardware is designed for use on vertical walls
constructed of wood studs or solid concrete. A wood stud wall is defined as consisting of a minimum of 2x4 wooden studs (2” wide by 4” deep) with a maximum of
5/8” drywall. The included hardware is not designed for use with metal studs or cinderblock walls. If you’re uncertain about the construction of your wall, then
please consult a qualified contractor or installer for assistance. For a safe installation, the wall you are mounting to must support 4 times the weight of the total load.
If not, then the surface must be reinforced to meet this standard. The installer is responsible for verifying that the wall structure and hardware used in any
installation method will safely support the total load.
TOOLS NEEDED
SYMBOLS
Drill
Level
Caution
3/16”5/16”
4.8 mm 8 mm
Tighten Socket Wrench
Pencil Mark
Screwdriver
Heavy!
P2
HARDWARE PART NUMBERS
2 1 3
M4 x 12
X 4
M5 x 12
X 4
5
6 mm x
65 mm
WALL
SCREWS
X 2
M6 x 12
X 4
PRODUCT COMPONENT PARTS
4
M5 x 20
X 4
6
ANCHOR
X 2
A1
ADAPTER
SCREWS
X 4
ADAPTER HARDWARE
A2
M8M5
ADAPTER
X 4
A3
ALLEN
WRENCH
X 1
A4
FIXED
WRENCH
X 1
B
A
C
Product Components
Contents Qty
A 1 Wall Plate/ Arm Assembly
B 1 VESA Monitor Plate
C 4 Monitor Adapters
B
Description
P3
PRODUCT DIMENSIONS AND SPECIFICATIONS
60 lbs
MW60C44
P4
STEP 1- REMOVE VESA MONITOR PLATE FROM MOUNT ASSEMBLY
Separate adapter from mount
B
VESA MONITOR
PLATE
Remove and save Phillips
head screw. Screw will
be used to reattach VESA
Monitor Plate in Step 4.
X1
ADAPTER CONFIGURATIONS
200mm x 100mm 100mm x 200mm
200mm x 200mm
P5
STEP 2- BACK FLAT PANEL (VESA MONITOR PLATE)
Connect VESA monitor plate to flat panel
Use M8M5 adapter with 5mmx 12mm
screw or 5mm x 20mm screw if flat
panel has 8mm inserts. Insert into 8mm insert
on back of flat panel then follow steps below
The wall screws should be tightened to
the wall with socket wrench
X2
5
6 mm
WALL
SCREW
P7
STEP 3B – SOLID CONCRETE INSTALLATION
Drill pilot hole
Solid Concrete
STEP 3B- DRILL PILOT HOLE AND MOUNT WALL PLATE
Drill bit size/ pilot hole depth
DRILL BIT
NOT INCLUDED
The wall screws should be tightened to
the wall with socket wrench
5
6 mm
WALL
SCREW
6
ANCHOR
5
6 mm
WALL
SCREW
P8
STEP 4- ATTACH PANEL TO MOUNT
Hang with monitor attached
Locking mechanism
Heavy, Assistance
Required
STEP 5- LEVEL AND ADJUST TILT
Secure VESA Monitor Plate to
mount with Phillips screw from
Step 1. Do not over-tighten screw.
Adjust tilt and elbow points
A3
A4
Flat panel can be leveled (+/- 3 degrees) as
needed. If Philips screw is tensioned too tight it
will be difficult to adjust leveling.
FIXED
WRENCH
X 1
A3 A4
ALLEN
WRENCH
X 1
P9
WARRANTY INFORMATION
Manufacturer warrants this product against defects in material or workmanship for the original
purchaser of the product with the following conditions:
WARRANTY PERIOD:
"The three-Year Limited Manufacturer’s Warranty” covers this product against defects in materials or
workmanship from the date of purchase by the original consumer for a period of three (3) years for
parts and labor.
SERVICE:
If the product fails under normal use due to a manufacturing defect within the warranty period, the
consumer will be responsible for the cost of shipping the product to an authorized service center -
NXG Technology will pay for the return shipment. Manufacturer will repair or replace the defective
item with a new or factory rebuilt replacement at Manufacturer’s discretion. The warranty will be
equal to the remainder of the original limited warranty period on the original product or for 90 days
after the date of repair / replacement, whichever is longer. All services must be performed by an
Authorized Service Center. All replaced parts will be the property of Manufacturer.
To obtain warranty service please send an email to support@nxgtechnology.com.
COVERAGE:
Manufacturer's liability under this limited warranty shall in no event exceed the cost of authorized
repairs, replacement with a similar product, reimbursement for authorized repairs or replacement, or
the original cost of the product at the time of purchase, whichever is less.
• This warranty is valid in the continental United States of America.
• Proof of purchase in the form of a bill of sale, invoice or sales receipt, which is evidence that the
unit is within the warranty period, must be presented to obtain warranty service
LIMITATION OF LIABILITY:
There are no other expressed warranties, whether written or oral, other than this printed limited
warranty. All implied warranties, including without limitation the implied warranties or merchantability
or fitness for a particular purpose, are limited to the durations of this limited warranty.
In no event shall NXG Technology be liable for incidental or consequential damages of any nature
whatsoever, including but not limited to lost profit or commercial loss, to the full extent those
damages can be disclaimed by law.
Some states do not allow the exclusion or limitation of incidental or consequential damage, or
limitation of the duration of implied warranties, so the preceding limitations or exclusions may not
apply to all purchasers. This warranty gives the original purchaser specific legal rights, and you may
also have other rights, which may vary from state to state.
P10
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.