NXG Technology NX-HDMIX-WP-IR-50 User Manual

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS

WARRANTY

NXG products are designed to the highest possible value and performance standards. Our
confidence in their quality is such that NXG Technology offers customers this transferable
limited warranty:

NXG Products Two-Year Limited Warranty

If the NXG products prove to be defective in workmanship or materials within two years from
the date of the original customer’s purchase, we will, at our option, repair or replace the defec­tive products.

DISCLAIMER

THE WARRANTY STATED HEREIN IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE AND ALL OTHER LIA­BILITIES AND OBLIGATIONS OF NXG TECHNOLOGY, ALL OF WHICH ARE EXPRESSLY DISCLAIMED.
NXG TECHNOLOGY HAS NOT MADE AND DOES NOT HEREBY MAKE ANY OTHER REPRESENTATION,
WARRANTY OR COVENANT WITH RESPECT TO THE CONDITION, QUALITY, DURABILITY, DESIGN,
OPERATION, CAPACITY, FITNESS FOR USE OR SUITABILITY OF THE NXG PRODUCT.

Exclusion of Certain Damages

NXG Technology’s liability for any defective product is limited to repair or replacement of prod­uct at our option. NXG T
of any kind or character because of product defects. Some states do not allow limitations on
how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitations and exclusions may not apply.

echnology shall not be liable for incidental or consequential damages

This Warranty Does Not Cover:

• Damage caused by abuse, accident, misuse, negligence, or improper operation.

• Any product whose serial number has been altered, defaced, or removed.

• Products that have been altered or modified.

• Normal wear and maintenance.

• Damages caused by shipping. (All claims for shipping damage must be made with the carrier.)

Warranty Service

Warranty service must be performed by an authorized
service center, usually an NXG dealer or its authorized
agent. All warranty repairs must be accompanied by
the original bill of sales. No other document is accept­able or is required. This warranty gives you specific
legal rights, and you may also have other rights which
vary from state to state.

4 1

Scottsdale,

email: [e-mail]

web: nxgtechnology.com

AZ

NX-HDMIX-WP-IR-50

HDMI Wall Plate Extender

568B

DEAR CUSTOMER

Thank you for purchasing this NXG product. For optimum performance and safety, please
read these instructions carefully before connecting or operating this product. Please keep
this manual in a safe place for future reference.

FEATURES

• Includes one transmitter and one receiver fitting North American Decora™wall plate sizes.

• The product operates using Dual UTP cable (Cat5E/6) as a substitute to expensive long HDMI
cable runs. The RJ45 connections must follow the IEEE-568B standard.

• Transmission distance reaches up to 50 meters (165’) at 1080P

• Automatic feedback, equalization and amplification adjustments

• Signal rates up to 2.25Gbits in support of 1080P

• Pass through infrared control signals for the remote source

• DC5V Power Supply for receiver (RX)

NOTICE

NXG Technology reserves the right to make changes
in the hardware, packaging and any accompanying
documentation without prior written notice.

PACKING CONTENTS

1) Main Unit. HDMI Wall Plate

2) DC5V Power Supply for receiver

3) Operating Instructions

4) IR TX unit (IR emitter cable)

5) IR RX unit (IR receiver cable)

TABLE OF CONTENTS

Packing Contents

Specifications

Connections

Connecting and Operating

ypical Application

T

Maintenance

Product Service

arranty

W

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS

SPECIFICATIONS

Operating Temperature Range -5 to +35C(-41 to +95)

Operating Humidity Range 5 to 90%RH (No Condensation)

Input Video Signal 0.5-1.0 Volts P-P

Input DDC Signal 5 volts p-p (TTL)

Support Video Format DTV/HDTV:480i/576i/480P/576P/720P/1080i/1080P

HDMI Output HDMI 1.3, HDCP 1.1

Support Audio Format DTS-HD Master Audio0Dolby true-HD etc.

Transmission Distance 1080P 8-bit 50m(Maximum) over CAT5E/CAT6 /24AWG/Solid

(Recommend to use 23AWG Cat6 cable)

Power consumption 3 watts (Maximum)

Dimension (L x W x H) 115 x 70 x 35mm

IR Wavelength & Frequency Wavelength: 940nm, frequency: 38kHz

Net Weight 260g(Pair)

Note 1: Specifications are subject to change. Mass and dimensions are approximate.
Note 2: When in 36Bit deep color mode, we suggest setting the HDMI source device to 1080i or 720p.

CONNECTIONS TRANSMITTER (TX)

Front Panel

Rear Panel

1. HDMI input port

2. Power input port

3. IR/TX

4. Indicator of HDMI input

5. Indicator of power input

6. CAT5e/6 output ports

CONNECTING THE NX-HDMIX-WP-IR-50

1) Connect the HDMI source output into the HDMI IN on the front plate of the

NX-HDMIX-WP-IR-50 (TX). (TX = Transmitter/ RX = Receiver)

2) Connect two CAT-5E or CAT6 cables to both the outputs of NX-HDMIX-WP-IR-50 (TX)

and inputs of NX-HDMIX-WP-IR-50 (RX). Please pay attention to the correct connection of
the two cables, CAT5e/6-1->CAT5e/6-1 (The RJ45 connections must follow EIA/TIA 568B).

3) Connect the HDMI source input into HDMI OUT on the front plate of the

NX-HDMIX-WP-IR-50 (RX).

4) Connect the IR TX UNIT into NX-HDMIX-WP-IR-50 (TX). Permanently affix the TX IR emitter

over the source components IR window by removing the adhesive backing. In order to work
properly, the emitter must be placed on the source component IR receiver window.

5) Connect the IR RX UNIT into NX-HDMIX-WP-IR-50 (RX). The RX IR receiver should be

placed in direct line of sight with the handheld remote. Consider affixing the IR receiver on

the TV frame or base.
NOTE: In some cases the power adapter could be taken off. The power adapter is needed when
the signal source isn’t sufficient enough to drive the HDMI signal. Gently Insert/Extract cables.

TYPICAL

APPLICATION

Front Panel

RECEIVER (RX)

Rear Panel 1. HDMI output port

2. Power input port

3. IR/RX

4. Indicator of HDMI input

5. Indicator of power input

6. CAT5e/6 input ports

2 3

MAINTENANCE

When cleaning this unit, use only a dry soft cloth. Never use an alcohol
based cleaner, paint thinner or other harsh cleaning chemical. Be careful not
to dislodge the TX IR emitter from its permanent position on the Source IR window.

PRODUCT SERVICE

1) Damage requiring service: The unit should be serviced by qualified service personnel if:

(a) The DC power supply cord or AC adaptor has been damaged;

Objects or liquids have damaged the unit;

(b)

(c) The unit has been exposed to rain;

(d) The unit does not operate normally or exhibits a marked change in performance;

(e) The unit has been dropped or the cabinet damaged.

2) Do not attempt to service the unit beyond that described in these operating instructions.

Unauthorized service may result in fire, electric shock, or other hazards and will void
all warranty.