nvent raychem touch 1500 Installation Instructions Manual

WARNING:

IMPORTANT:

TOUCH 1500

User Interface Terminal for
Systems Installation Instructions

TOUCH 1500
installed in a panel

KIT CONTENTS

Qty Description

1 TOUCH 1500 display
10 Mounting clips
1 ADAM 4069-CID2 relay module
1 5-ft 9-pin RS-232 (null modem) cable

APPROVALS/CERTIFICATIONS

Nonhazardous Locations

E180881

I.T.F.

General

Area of use Nonhazardous, Indoors (IP65, NEMA 4)
Supply voltage 10 – 30 Vdc

Amperage rating

Operating
temperature
Storage
temperature
Dimensions 449.9 mm W X 315.6 mm H X 141.7 mm D

Alarm Outputs

Relay output One Form C relay rated at 3 A @ 250 Vac.

LCD Display

Display LCD is a 15-in XGA, color TFT transective device with

Touch Screen 4-wire resistive touch screen interface for user entry

Steady state
Surge current 16 A
0°C to 50°C (32°F to 122°F) w/o space heater, –30°C to 50°C
(–22°F to 122°F) using space heater and screen cover
–20°C to 60°C (–4°F to 140°F)

(17.74 in. W X 12.44 in. H X 5.58 in. D)

Relay is used as a common alarm.

integral CCFL backlight

1.8 A

RAYCHEM

NGC

DESCRIPTION

The nVent RAYCHEM TOUCH 1500 is a panel mounted touch screen display used in
conjunction with nVent RAYCHEM NGC-40 and NGC-20 (Europe only) control and monitoring
devices. The TOUCH 1500 is rated IP 65 (NEMA 4) and is approved for nonhazardous indoor
locations. The TOUCH 1500 kit includes all hardware required for mounting in a suitable
electrical panel. These instructions describe how to mount the TOUCH 1500 in an electrical
panel and are intended only for personnel experienced in panel construction.

TOOLS REQUIRED

• Masking tape • #16 (3/16) drill bit

• Metal file • Phillips screwdriver

• Jig saw (recommend using carbon steel blade with 24TPI)

ADDITIONAL MATERIALS (TO BE ORDERED SEPARATELY)

Qty Description Manufacturer Manufacturer PN

2 9 pin D-Sub to 10 pin terminal block PCB Phoenix Contacts 2315162

2 Serial Communication cable L-COM "CSMN9MF-xx

11 Terminal Blocks Weidmuller 163205
1 Type ZS1 Fuse Block Weidmuller 161649
4 PE Terminal (Earth Ground) Weidmuller 1632080000
6 End plates / Partition Weidmuller 1632090000

1 End plate / Partition Weidmuller 1896330000
6 End Plate Stops Weidmuller 38356
2 Jumpers, 2 Position Weidmuller 1608950000
2 Jumpers, 3 Position Weidmuller 1608960000
1 Fuse, 1 amp, 250 V Square D MLD-1
1 Power Supply, 24 Vdc, 2.5 Amp Mean Well DR-120-24
1 Push to test alarm light; Idec 24 Vdc Idec ALW29911-D-R-24

xx=Length in Ft."

Network Connection

Local/
Remote Port

Local RS-232 A non-isolated, 9 pin D sub male
Remote RS-485 2-wire isolated, 9 pin D sub male
Data rate 9600 to 57600 baud

Maximum cable
length
Field Port RS-485, 2-wire isolated. Used to communicate with

Signals 2-wire isolated, 9 pin D sub male

Data rate To 9600 baud
LAN 10/100 Base-T Ethernet port with Link and Activity Status

USB Ports USB 2.0 Host port Type A receptacle (X4)

* RS-232/RS-485 ports may be used to communicate
with host computers DTS (nVent RAYCHEM Supervisor
Software) or DCS

For RS-485 not to exceed 1200 m (4000 ft). Cable to be
shielded twisted pair.

external devices, such as nVent RAYCHEM
NGC-40-BRIDGE. Maximum cable length not to exceed

1200m (4000 ft). Cable to be shielded twisted pair.

LEDs (X2)

FIRE HAZARD: The Touch 1500 must not be used in
hazardous locations. Electrical components within the unit
could ignite flammable gases. Do not install the unit where it
may be exposed to flammable gases.

The TOUCH 1500 is an electronic unit. During installation, take
the following precautions to avoid damage to its electronic
components.

• Handle with care to avoid mechanical damage.

• Keep electronics dry.

• Avoid exposure to static electricity.

• Avoid contamination with metal filings, liquids, or other
foreign matter.

• Use agency-approved conduit bushings, adapters, and cable
glands to keep the enclosure protected from dust and fluids.

Provide Suitable Panel Enclosure, and Determine Locations for TOUCH 1500 Assembly in Panel X

1. Provide suitable panel enclosure

To protect its electronic components, the TOUCH 1500
must be mounted in a non-hazardous location panel with
a minimum IP32 (NEMA 1) enclosure. An IP52 (NEMA 12)
or better enclosure is recommended. The TOUCH 1500
assembly comes with a sealing gasket and hardware to
mount the enclosure.

Note: The RAYCHEM TOUCH 1500 is designed for
operation in ambient temperatures from 0°C to 50°C (32°F
to 122°F). If the ambient temperature is outside this range,
a space heater with screen window kit and/or cooling fan
will be required in the panel.

Panel
door

assembly location

Alarm
light

2. Determine locations for the TOUCH 1500 assembly in the
electrical panel

The TOUCH 1500 should be located on the front of the
panel near eye level (for convenient viewing). The TOUCH
1500 assembly is an electronic unit and must not be
located where it will be exposed to strong magnetic fields
or excessive vibration.

PanelTouch 1500

C1

C2 C3 C4 C5 C6 C7 C8 C9 C10

1

3

5

7

9

11

13

15

17

19

CB1

CB2
CB4

CB3
CB5

CB6

CB7

CB8

CB9

CB10

CB11

CB12
CB14

CB13

CB16

CB15

CB18

CB17

CB20

CB19
CB21

CB22

CB23

CB24

CB25

CB26

CB27

CB28

CB29

CB30

CB31

CB32

CB33

CB34

CB35

CB36

CB37

CB38

CB39 CB40

CB42

2

4

6

8

10

12

14

16

18

20

2 | nVent.com

21

23

25

27

29

31

33

35

37

39

22

24

26

28

30

32

34

36

38

40

Cut Opening and Mount TOUCH 1500 on Front of Panel

1. Locate the TOUCH 1500 on front of panel

Locate the TOUCH 1500 assembly on the front of the panel
at a level convenient for viewing. Make sure the cover on
the back of the assembly will not interfere with existing
panel hardware.

Panel Door

292 mm

11.5 in.

422 mm

16.6 in.

Cutting

Area

Note: Cutting the opening for the display is a craft sensi­tive procedure; if it is not done correctly, the panel door
can be damaged. The procedure for laying out and cutting
the opening for the display must be undertaken with

care, and by personnel qualied and experienced in panel

construction.

2. Prepare and mark the position of the display opening and
mounting holes

• Use the cut-out directions to lay out the opening for the
TOUCH 1500 display.

• Apply two layers of masking tape around the outer pe­rimeter of the intended opening to prevent scratching the
panel surface with the jigsaw.

3. Cut the display opening

Cut the opening for the TOUCH 1500 with a jigsaw using
a 24 TPI blade. Take care not to damage the panel door.
Remove all rough edges and burrs with a metal file before
proceeding.

Note: The following steps are most easily accomplished if
the panel door is on a horizontal surface.

4. Mount the user interface assembly onto the panel door

• Place the TOUCH 1500 assembly in position. Secure the
screen to the enclosure with the 10 mounting clips.

TOUCH 1500 display

G

+–

Inside of
panel door

Panel door

G

+–

TOUCH 1500 display
with sealing gasket

• Place the supplied mounting clips in each slot along the
sides of the TOUCH 1500. Fasten only hand tight.

TOUCH 1500 display

G

+–

Mounting clips

• Look at the front of the panel, and align the TOUCH 1500
assembly so it is level (loosen clips if necessary to reposi­tion the assembly).

• After the display is properly positioned, tighten the mounting
clips. Do not overtighten and risk damage to hardware.

nVent.com | 3

TOUCH 1500 Cut Out Dimensions

(11.5 in)

292 mm

Panel Cut Out

Panel Cut Out

422 mm
(16.6 in)

Top of Display

Panel Cut Out Area

Drawing

Drawing

NOT TO SCALE

NOT TO SCALE

4 | nVent.com

TOUCH 1500 Connection Diagram

Incoming

power

+ – G

Reset

Switch

RS-232

Com 1

Remote Port

Connect Power

Connect 10 – 30 Vdc to the male power connection tting

located on the bottom side of the TOUCH 1500. Note the polarity
of the wires.

Ethernet

Ethernet

Field Port

USB port (X4)

RS-485

Com 4

Remote Port

Compact flashKeyboardMouse

RS-485

Com 3

Field Port

G

10 – 30 Vdc

–

+

Incoming

power

+ – G

Communication

The TOUCH 1500 has two isolated RS-485 ports located at the
bottom.

Field Side Port (RS-485)

The RS-485 port labeled “Com 3” is the eld side port that

is used to communicate with ModBus devices (ie. NGC-40­BRIDGE and NGC-20).

*Remote Port (RS-485) – Optional

The RS-485 port labeled “Com 4” is the Remote side port
that is used to communicate with to a host computer DTS
(using RAYCHEM Supervisory Software) or to a DCS.

*Local Host Port (RS-232) – Optional

The RS-232 port can be used as local Host port that is used
to communicate with to a host computer (using RAYCHEM
Supervisory Software).

nVent.com | 5

Field Port Communication RS-485 Common Alarm Light and Alarm Relay

Mount the supplied ADAM 4069-CID2 module, 9-pin D sub to 10
pin terminal block and 4 terminal block (with 2 position jumpers)
on a DIN rail inside the panel enclosure. Mount the alarm light on
the panel's door below the touch screen.

Wire per the schematic below.

Shield

Data +

Field port (to Bridge, NGC-20)

Data –

2

1

RL4NO

RL4COM

ADAM-4069-CID2

RL5NO

RL5COM

Alarm Lamp

3

24 V Lamp

4

Idec Switch/Lamp

Alarm
Lamp

RL2NC

RL2NC

RL1NC

RL3NO

RL3COM

RL2COM

RL1COM

RL6NO

RL6COM

RL7NC

RL7COM

RL7NCNCINT+

Jumpers

RL0NO

RL1NO

RL0NC

RL0COM

(Y) DATA +

(G) DATA –

(R) +Vs

(B) GND 10

5 4 3 2 1

T 9 8 7 6

Field

Port

Com 3

+

–

Ground

120/230 Vac

+ – G

5 4 3 2 1

T 9 8 7 6

Remote

Port

Com 4

(See wiring below)

Serial communication

cable to Field Port/Com 3

(RS-485)

TOUCH 1500

Jumpers

RS-485

RS-485

To Remote Port/Com 4 (RS-485)

Door mounted

Data +

To host computer

Shield

Data –

Remote Port Connection

* Mount the supplied 9-pin D sub to 10-pin terminal block on a

DIN rail inside the panel enclosure.

Wire per schematic to the right.

6 | nVent.com

5 4 3 2 1

T 9 8 7 6

Remote

Port

Com 4

Overview of Wiring

Common alarm relay

Shield

Data +
Data –

Data +
Data –

Field Port

Remote Port

Ø or N

G
Ø

RL2NC

RL2NC

RL1NC

RL4NO

RL3NO

RL3COM

RL2COM

RL1COM

RL1NO

RL4COM

ADAM-4069-CID2

RL5NO

RL5COM

RL6NO

RL6COM

RL7NC

RL7COM

RL7NCNCINT+

(Y) D ATA +

2

1

RL0NC

RL0NO

RL0COM

(G) DATA –

(R) +Vs

(B) GND 10

Jumpers

Alarm Lamp

3

24 V Lamp

4

Idec Switch/Lamp

Alarm
Lamp

5 4 3 2 1

T 9 8 7 6

Field
Port

Com 3

5 4 3 2 1

T 9 8 7 6

Remote

Port

Com 4

Ground

Jumpers

Incoming

Power Terminal

Block

+

–

+ – G

TOUCH 1500

Door mounted

nVent.com | 7

Servicing

The TOUCH 1500 contains no user-serviceable parts. Contact your

nVent representative for service and an authorization number if

required.

Cleaning

The touch screen area of the TOUCH 1500 may be cleaned with a
damp or dry cloth. Typical window cleaning agents may be applied
to aid in the removal of dirt, dust and grease. Do not use abrasive
cleaners.

Reset Switch

The Reset switch can be
found on the bottom of the
TOUCH 1500.

North America

Tel [phone]
Fax [phone]
[e-mail]

Reset

Switch

+ – G

Europe, Middle East, Africa

Tel [phone]
Fax [phone]
[e-mail]

Asia Pacific

Tel [phone]
Fax [phone]
[e-mail]

Latin America

Tel [phone]
Fax [phone]
[e-mail]

©2018 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its aliates. All other trademarks are the property of their respective owners.
nVent reserves the right to change specications without notice.

Raychem-IM-H58559-INSTALL170-Touch1500-EN-1805

nVent.com