Page 1
Operation manual
LED Flush mount light
Blink Plus Series
With Integrated Dimmable Driver
Thank you for purchasing our product. This fixture has
been manufactured from components with advanced
optoelectronics to ensure high reliability and long life.
Before assembling please read this Operation Manual
carefully and save in a safe place for future reference.
Please note that all electrical connections must be in
accordance with local and National Electrical Code
standards as well as local building codes. In case you are
not familiar with proper wiring connections and building
codes, consult a qualified electrician.
Safety recommendations
RISK OF ELECTRIC SHOCK – THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE
1.
WITH APPLICABLE INSTALLATION CODES BY A PERSON FAMILIAR WITH MENTIONED
ABOVE CODES AND HAZARDS INVOLVED. DISCONNECT POWER AT CIRCUIT BREAKER
OR FUSE BEFORE INSTALLING OR SERVICING.
2. Before use of the product carefully read the whole Operation Manual.
3. THE PRODUCT IS PURPOSED FOR INTERIOR USE ONLY, SUITABLE FOR
DAMP LOCATIONS.
4. Protect the product against direct contact with water.
5. Assemble the product only with the use of parts provided and the housing;
improper assembly may result in device failing which could damage the product,
personal property or cause injury.
6. Assembly shall follow with accessories delivered with the set only.
7. The device is not a toy, KEEP OUT OF REACH OF CHILDREN.
Copyright © 2016
Satco Products, Inc.
All Rights Reserved.
National Toll-Fre e:
800- 43-SATCO
(800-437-2826)
www. nuvolighti ng.com
Distribut ion Centers:
New York, Florida ,
Texas, Washington ,
California, Pu erto Rico
Satco Produc ts Inc.
110 Heartland Blvd.,
Brentwoo d, NY 11717
PH 631-243-2022
FX 631-243-2027
Specifcations:
Blink Plus
Operating Voltage:120/277VAC
Dimming: Triac (Dimming only @120V)
Power consumption: 18W/20W/22W/30W/40W/45W
Color Temp.: 2700K/3000K/4000K/5000K
Life span: 50,000h
Illumination authorization<5%
per 10,000h
Page 2
Mounting Bracket Installation
Step 1
Turn-off /disconnect
power at circuit breaker.
Attach connector
(provided) to AC
cable from junction box:
L side to Black AC wire
N side to White AC wire
Wiring
Step 4
Attach ground wire from
fixture to ground wire
from junction box by using
wire nut (provided).
Step 2
Position bracket in place:
Mark mounting hole
positions on ceiling with
reference on bracket.
Drill holes, mount
appropriate anchors, then
secure screws into anchors.
Step 5
Next ’plug’the
two sides of the
orange wire
connector together.
Step 3
Attach the bracket to junction
box using the 2 screws
(provided).
Pull the AC cable with
connector through the bracket
center hole.
Lock In Place
A
B
Step 6
Lift fixture up against bracket.
Align the arrow sign from
bracket to unlock-sign from
fixture.Slide to locked-sign
to lock fixture in place. Remove
label.
Installed-Congratulations...
Enjoy the light!
Dimming
This product is compatible with most residential type dimmers available on the market.
T he dimming performance will depend on kind of dimmer and dimmer settings.
Visit Satco.com for an up to date list of compatible dimmers.
Cleaning
• Clean with a soft or damp cloth. While cleaning with the damp cloth make sure
the power is off.
• Do not clean with liquids or abrasives.
5 Year limited warranty
The purchased product is covered with a 5 year warranty in respect of any defect in
material
exposure to natural hazard, or excessive use over the limits specifed for the unit, or if
any unauthorized alteration or repair followed.
or workmanship after purchase date.
Satco shall bear no responsibility on account of guarantee, as well as shall bear no
liability for any faults, in case of improper operation, use negligence, accident or
www.satco.comcustomer service 1-800-43-SATCO
32
Loading...