NuTone WS1, WS130AA User Manual

ALLURE

™

WS1 SERIES RANGE HOODS

READ AND SAVE THESE INSTRUCTIONS

FOR DOMESTIC COOKING ONLY

ALLURE™ WS1 SERIES

RANGE HOOD

Page 1

Patent No.: US D450, 829 S

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society of Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. To reduce the risk of fire or electric shock, do not use this range hood with an additional speed control device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of fire, use only metal ductwork.

9. Use with approved cord-connection kit only.

10.This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when cooking flaming foods.

3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN — You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result.

4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher and you already know

how to operate it. B. The fire is small and contained in the area where it started. C. The fire department is being called. D. You can fight the fire with your back to an exit. * Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit.

3. For best capture of cooking impurities, your range hood should be mounted so that the top of the hood is 24-30” above the cooking surface.

4. Please read specification label on product for further information and requirements.

Installer: Leave this manual with the homeowner.

Homeowner: Operating and Cleaning information on page 5.

NOTE If hood is to be installed Non-Ducted: Purchase a set of (2) non-ducted filters from your

local distributor or retailer and attach them to the aluminum mesh filters.

TABLE OF CONTENTS

This manual is divided into sections as follows:

“PREPARE HOOD LOCATION”

Run ductwork from roof or wall cap, and electrical wiring from service

panel - to installation location

“PREPARE THE HOOD” Get your hood ready for installation

“CONNECT WIRING”

Make electrical wiring connections to hood

“INSTALL HOOD” Secure hood to cabinet and ductwork - install bulbs and filters

“OPERATION” How to use the hood controls

“CLEANING” Keep your hood in top working condition

“SERVICE PARTS”

Part numbers and exploded view of hood components

“WARRANTY” One-year limited warranty and how to contact us

ALLURE™ WS1 SERIES

CABINET BOTTOM

CABINET FRONT

HORIZONTAL DUCT

ACCESS HOLE

5¼"

7½"

¾"

(30" hood)

(36" hood)

(30" hood)

HOOD

MOUNTING

SCREWS (4)

ELECTRICAL

ACCESS HOLE

(in wall)

3¾"

(36" hood)

CENTER

LINE

WOOD SHIMS

(recessed-bottom

cabinets only)

(42" hood)

SOFFIT

24" - 30" ABOVE COOKING SURFACE

CABINET

3¼" X 10" DUCT (For horizontal discharge)

WALL CAP

ROOF CAP

3¼" X 10"

(For vertical

discharge)

HOUSE WIRING (Top or Back of hood)

HOODHOOD

VERTICAL DUCT

ACCESS HOLE

1¼"

1½"

10½"

5¼"

CENTER

LINE

HOOD MOUNTING SCREWS (4)

ELECTRICAL

ACCESS HOLE

(in cabinet bottom)

WOOD SHIMS

(recessed-bottom

cabinets only)

CABINET FRONT

CABINET BOTTOM

(30" hood)

(36" hood)

7½"

(42" hood)

(30" hood)

(36" hood)

(42" hood)

RANGE HOOD

Page 2

PREPARE HOOD LOCATION

3¼” x 10” or

7” ROUND DUCT

(For vertical discharge)

1 Determine whether hood will discharge vertically (3¼” x 10”

or 7” Round), horizontally (3¼” x 10” only) or non-ducted. For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitons and elbows.

2 Use diagrams, below, for proper placement of ductwork and

electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole.

3¼” X 10”

VERTICAL DUCTING

PREPARE HOOD LOCATION

7” ROUND

VERTICAL DUCTING

3 Run house wiring between service panel and hood location.

PREPARE THE HOOD

7” ROUND

DUCT PLATE

3¼” X 10”

HORIZONTAL DUCTING

1 Remove 7” Round Duct Plate from top of hood. Set duct

plate aside - with mounting screws.

FILTERS

2 Remove tape holding Filters in place. Pull down on filter

tabs and lift filters out. Set filters aside.

ALLURE™ WS1 SERIES

PREPARE THE HOOD PREPARE THE HOOD

RANGE HOOD

Page 3

3 Remove

Damper/Duct Connector from

inside the hood. Set connector aside - with mounting screws and parts bag.

DAMPER/DUCT

CONNECTOR

4 Remove Wir-

ing Cover from inside the hood. Set cover and mounting screw aside.

WIRING

COVER

5 Remove either

top or back wiring knockout and install approved

Electrical Cable Clamp.

7 Remove Air

Chute - held in

place with one (1) screw.

NOTE: Be care-

ful not to disconnect any wires.

8 Remove Baffle

from air chute.

AIR CHUTE

BAFFLE



BAFFLE



ELECTRICAL CABLE CLAMP

Non-Ducted Installation - Skip to “Connect Wiring” section.

(3) #8 SCREWS

The following

PANEL

Steps (6 thru

13) are for

(2) #8 SCREWS

DUCTED INSTALLATION ONLY.

6 Remove Light Panel - held in place with (3) #8 screws

and (2) #8 screws. Disconnect light assembly wire harness (white connector).

LIGHT

9 Rotate baffle. Re-

insert baffle into air chute (as shown) so that baffle tabs fit all the way into slots in air chute. An audible “click” will be heard when fully installed. This will close off the air flow through the non-ducted slots on top of hood.

SLOTS



Re-install air chute, re-connect wire

harness, and replace light panel.

NOTE: Be careful not to trap wires

between support fin and light panel.



TABS



SUPPORT FIN

ALLURE™ WS1 SERIES

RANGE HOOD

Page 4

PREPARE THE HOOD

TOP RECTANGULAR

DUCT KNOCKOUT

(Remove for 3¼” x 10”

Vertical & for 7” Round

Discharge)

REAR

RECTANGULAR

DUCT KNOCKOUT

(Remove for 3¼” x 10” Horizontal Discharge)

11 Remove appropriate Duct Knockout(s) from top or back of

hood.

UP TO 1” SIDE-TO-SIDE ADJUSTMENT

TAPE

SEMI-CIRCULAR

DUCT KNOCKOUT

(Remove for 7” Round

Discharge)

TOP/BACK

EDGE

CONNECT WIRING

WARNING: To reduce the risk of electric shock, make sure power is switched off at the service panel. Lock or tag service panel to prevent power from being switched on accidentally.

HOUSE

WIRING

(120 VAC)

CARDBOARD

(Use to protect

cooktop)

1 Connect House Wiring (120 VAC) to hood. Use a piece of

Cardboard to protect the cooktop, if necessary.



PIVOT

3¼” x 10” Ducted Discharge Only: Attach Damper/Duct

Connector over knockout opening. Make sure damper Pivot is nearest to Top/Back Edge of hood. Remove Tape from damper flap.

7” Round Ducted Discharge Only: Re-install 7” Round Duct

Plate removed in Step #1 under “PREPARE THE HOOD” section. Install a 7” round damper (purchase separately). Damper flap must open freely in direction of air flow (away from range hood).

NOTE

up to ½” on either side of hood center. In extreme off-center installations, one end of the duct connector may need to be trimmed to clear the electrical cable clamp.

To accomodate off-center ductwork, the Damper/Duct Connector can be installed up to 1-inch on either side of hood center or the 7” Round Duct Plate can be installed

DAMPER/DUCT

CONNECTOR

(Vertical discharge

position shown)

GREEN

GROUND

SCREW

2 Connect house black to hood black wire, house white to hood

white wire, and house ground under Green Ground Screw. Securely tighten cable clamp onto house wiring.

3 Replace wiring cover.

+ 8 hidden pages