NuTone EC50, 696NC, EC70, 695C, VSBP50M Installation Instructions Manual

INSTALLATION INSTRUCTIONS

ECONOMY VENTILATION FAN

MODELS: EC50 & EC70, 696NC & 695C, VSBP50M

HOUSING INSTALLATION

Rough Opening: 8¼” long x 7¼” wide
Housing Size: 7

3

⁄16” x 81⁄16” x 37⁄8”

Refer to Figure 1A. Remove motor plate from housing before
mounting. Insert screwdriver between motor plate and side of
housing with duct collar. Gently pry the housing away from the
motor plate while pulling up on the motor plate to disengage the
plate from the housing.

1. With nails or screw, secure (but do not tighten) the housing to the
ceiling or wall through the two keyhole slots in the mounting tabs.

NOTE: Prior to completely tightening, adjust the housing so

that the outer edge will remain 1/8” to 1/4” recessed
from the finished ceiling or wall. For the grille to fit
properly, the housing must not extend outside the
finished wall surface.

2. Secure discharge adapter over flange on housing and connect
ducting to discharge, make sure housing is securely mounted
to prevent fan from vibrating and causing noise.

WIRING

IMPORTANT: Ensure all wiring complies with local codes and the

unit is properly grounded.

1. Refer to Figure 2. Run power leads from the wall or timer
switch to the unit.

2. Using approved wire connectors, connect supply wires to fan
wires: BLACK to BLACK and WHITE to WHITE. Connect
ground wire (GREEN to bare) to the GREEN ground screw in
the fan’s junction box.

30040605C

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the
address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service
panel.

3. Installation work and electrical wiring must be done by

qualified personnel in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment
manufacturer’s guidelines and safety standards such as
those published by the National Fire Protection Association
(NFPA), and the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE), and the local
code authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce the risk of fire and electric shock, do not use this

fan with any solid-state speed control device.

8. Suitable for use over a tub or shower when connected to a

GFCI (Ground Fault Circuit Interrupter) - protected branch
circuit.

9. This unit must be grounded.

10. When applicable local regulations comprise more restrictive

installation and/or certification requirements, the aforementioned
requirements prevail on those of this document and the
installer agrees to conform to these at his own expenses.

11. When performing installation, servicing or cleaning the unit, it is

recommended to wear safety glasses and gloves.

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2. Do not mount this product in a ceiling insulated to a value

greater than R40. This product is designed to be mounted in
a ceiling or in a standard 2” x 4” wall.

3. Do not use this product in kitchens.

4. To avoid motor bearing damage and noisy and/or unbalanced

impeller, keep drywall spray, construction dust, etc. off power
unit.

5. Please read specification label on product for further

information and requirements.

READ AND SAVE THESE INSTRUCTIONS

!

CAUTION

SECURE

FAN TO

HOUSING

PLUG INSERTS
INTO HOUSING’S
RECEPTACLE

TABS

SLOTS

FIGURE 1

FIGURE 1A

MOUNTING
TABS (TYP.)

FIGURE 2

REGISTER YOUR PRODUCT ONLINE AT

• For Broan EC50 or EC70: www.broan.ca

• For NuTone 696NC or 695C: www.nutone.ca

BLACK
WHITE

BE0009A

SWITCH
BOX

WHITEBLACK

120 V AC, 60 Hz
HOUSE POWER

FAN

HOUSING

One Year Limited Warranty

Broan-NuTone Canada warrants to the original consumer purchaser of its products that such products will be free from defects in materials and
workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Broan-NuTone Canada will, at its option, repair or replace, without charge, any product or part which is found to be
defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, BULBS OR BATTERIES, FILTERS, DUST, ROOF CAPS,
WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or
parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by Broan-NuTone Canada or an authorized
representative), faulty installation or installation contrary to recommended installation instructions.

The duration of any implied warranty is limited to the one-year period as specified for the express warranty.
BROAN-NUTONE CANADA’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE CANADA’S OPTION, SHALL BE THE PURCHASER'S

SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE CANADA SHALL NOT BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some
jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary by jurisdiction. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone Canada at the address or telephone number below, (b) give the model number and

part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence
of the original purchase date.

Date of Installation Builder or Installer

Model No. and Product Description

IF YOU NEED ASSISTANCE OR SERVICE:

For the location of your nearest Broan-NuTone Canada Incorporated dealer

Dial Free 1-888-882-7626

Please be prepared to provide:

Product model number • Date and Proof of Purchase • The nature of the difficulty

Broan-NuTone Canada Incorporated

1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9

www.broan.ca

www.nutone.ca

FIGURE 3

DUCTING

1. Refer to Figures 3 and 4. Run 3” round duct from the discharge

opening to the outside of the house.

INSTALLING THE FAN AND GRILLE

1. Refer to Figure 1. Insert the tabs into the housing’s slots.

2. Push the fan into the housing until it is secure against the electrical box.

3. As illustrated, tighten the screw and insert the plug into the
housing’s receptacle.
IMPORTANT: Ensure the blower wheel turns freely.

4. The grille may be installed when the finished walls have been
completed. Place the grille’s spring mounting clips into the fan unit.
Install the clips on both sides.

FIGURE 4

HORIZONTAL AND FROM
HORIZONTAL TO
VERTICAL DISCHARGE

FAN IN

BH0037A

VERTICAL AND FROM
VERTICAL TO
HORIZONTAL DISCHARGE

CEILING

3” ROUND DUCT

ROOF CAP

90° ELBOW

WALL CAP

3” ROUND DUCT

ROOF CAP

90° ELBOW &
WALL CAP
ASSEMBLY

FAN

IN WALL

BH0038A