ACCESSORY SPEAKER
READ AND SAVE THESE INSTRUCTIONS
APPLICATION
The SPKACC is a Hi-Fidelity, Bluetooth® wireless technology
enabled accessory that works with all QT-series Broan and
NuTone bath fans except: fans with humidity sensing, fans
equipped with heaters, and fans controlled with variable speed
controls.
The SPKACC can be used only with the models shown in this
chart:
BROAN
MODELS
QT110E QTN110E QTR090C QTN130EC
QT130E
QT130LE
QT140LE
QT140E
QTR080 QTN80L QTR110LC QTREN070C
QTR080L QTREN080 QTR110RC QTREN070FLC
QTR110 QTREN080FLT QTRE050RF QTREN080C
QTR110L QTREN110 QTRE070C QTREN090C
QT110LE QTREN110FLT QTRE070FLC QTREN090FLC
QTR140 QTRN080 QTRE075C QTREN110C
QTR140L QTRN080L QTRE080C QTREN110FLC
QTRE080 QTRN110 QTRE080C2S QTXEN050C
QTRE080FLT QTRN110L QTRE090C QTXEN080C
QTRE080R QTN130LE1
QTRE110 QTXEN050 QTRE110C QTXEN110C
QTRE110FLT QTXEN080 QTRE110RC QTXEN150C
QTRE110FLFT QTXEN080FLT QTRE110RF
QTXE050 QTXEN110 QTRE110FLC
QTXE080 QTXEN110FLT QTXE050C
QTXE080FLT QTXEN150
QTXE110 QTXEN150FLT *QTXE090C
QTXE110FLT QTREN080F QTXE110C
QTXE150
QTXE150FLT *QTREN110F FQTR110C
QTR050F QTREN110FLFT FQTRE050C
QTR080F QTRN050F FQTRE070C
QTR110F QTRN080F FQTRE080C
QTRE080F QTRN110F FQTRE110C
QTRE080FLFT QTXRN000HF FQTRE110MG
QTRE110F QTXRN000HL FQTXE050C
QT80E FQTXE110C
QT80L
QT90E
QT90L
SSQTXE080
SSQTXE110
NUTONE
MODELS
QTN110LE QTR090LC QTRN090C
*
QTN130E
*
QTN130LE QTR100C QTRN110LC
*
QTN80E QTR110C QTRN130EC
*
QTREN080FLFT QTXE150C
*
BROAN MODELS
CANADA
QTR090RC QTRN110C
*
QTRE090FLC QTXEN090C
*
QTXE080C
*
*
NUTONE MODELS
CANADA
*
*
*
* The SPKACC speaker
accessory WILL
ONLY FIT these
models if the models
were manufactured
before October 2015.
These models have
one of two styles of
metal motor bracket
shown in the SPKACC
installation manual.
The SPKACC speaker
accessory WILL NOT
FIT these models
if the models were
manufactured after
October 2015. These
models have the
motor surrounded by
a round, black plastic
housing/casing.
“RAISED”
MOTOR BRACKET
“FLAT”
MOTOR BRACKET
Determine which MOTOR BRACKET is used in your fan.
MODEL SPKACC
Page 1
INSTALLATION WITH “RAISED” MOTOR BRACKET
MODEL SPKACC
Page 2
1. TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS: Switch power off at service panel
and lock the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the service
panel.
LIGHT
WIRE
GRILLE
2. Remove fan GRILLE by squeezing two GRILLE SPRINGS
and sliding them out of their mounting slots on each side of
the fan housing. Disconnect LIGHT WIRE from fan (if fan is
equipped with a light). Set grille assembly aside for now.
GRILLE SPRING
#8-32 X 5/8”
SCREWS
FAN PARTITION
PLATE
BRACKET
OPENING
SPEAKER PLUG
FAN MOTOR
PLUG
3. Disconnect FAN MOTOR PLUG.
#8-32 X 5/8”
SCREWS
4. Partially install (2) #8-32 x 5/8 screws (included) into threaded
holes in speaker bracket - only so ends of screws are flush
with bottom surface of speaker bracket. Note: Installing
screws below flush will make the next couple of steps difficult.
SPEAKER WIRE
RECEPTACLE
FAN MOTOR PLUG
5. Insert speaker into fan housing. Make sure SPEAKER
BRACKET hooks over edge of BRACKET OPENING.
6. Make sure rear surface of speaker is located as close to
wall of fan housing as possible.
7. Turn #8-32 X 5/8” SCREWS (partially installed in Step
3) until they make contact with FAN PARTITION PLATE.
Alternately tighten both screws. DO NOT OVERTIGHTEN.
8. Insert SPEAKER PLUG into power receptacle where
motor plug was disconnected.
9. Connect FAN MOTOR PLUG into SPEAKER WIRE
RECEPTACLE.
10. Plug in LIGHT WIRE (if applicable) and re-install grille that
were unplugged and removed in Step 2.
11. Turn on power to fan.
12. Go to Bluetooth
speaker operating instructions.
®
Speaker Operation section for Bluetooth
®
INSTALLATION WITH “FLAT” MOTOR BRACKET
1. TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS: Switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
SPEAKER BRACKET
#8-32 X 3/8”
SCREWS
MODEL SPKACC
Page 3
LIGHT
WIRE
GRILLE
2. Remove fan GRILLE by squeezing two GRILLE SPRINGS
and sliding them out of their mounting slots on each side of
the fan housing. Disconnect LIGHT WIRE from fan (if fan is
equipped with a light). Set grille assembly aside for now.
FAN MOTOR PLUG
3. Disconnect FAN MOTOR PLUG.
SPEAKER MODULE
AUXILIARY BRACKET SPEAKER BRACKET
4. Attach AUXILIARY BRACKET (loose bracket in parts bag)
to SPEAKER BRACKET (attached to SPEAKER MODULE).
Partially install (2) #8-32 X 3/8” SCREWS (short screws
from parts bag) through larger holes in speaker bracket and
into auxiliary bracket - only so ends of screws are flush with
bottom surface of auxiliary bracket. Note: Installing screws
below flush will make the next steps more difficult.
GRILLE SPRING
#8-32 X 3/8”
SCREWS
MOTOR BRACKET OPENING AUXILIARY BRACKET
PARTITION
PLATE
MOTOR
BRACKET
SPEAKER PLUG
SPEAKER WIRE
FAN MOTOR PLUG
5. Insert speaker into fan housing. Make sure AUXILIARY
BRACKET hooks over edge of BRACKET OPENING.
6. Make sure rear surface of speaker is located as close to
wall of fan housing as possible.
7. Secure SPEAKER BRACKET to auxiliary bracket by
tightening the #8-32 X 3/8” SCREWS (partially installed
in Step 4). Alternately tighten both screws. DO NOT
OVERTIGHTEN.
8. Secure speaker to MOTOR BRACKET by installing other
two (2) #8-32 X 3/8” SCREWS into threaded holes in
AUXILIARY BRACKET. Turn screws until they make
contact with the sheet-metal “bump” in the fan opening of
the PARTITION PLATE. Alternately tighten both screws.
DO NOT OVERTIGHTEN.
9. Insert SPEAKER PLUG into power receptacle where
motor plug was disconnected.
10. Connect FAN MOTOR PLUG into SPEAKER WIRE
RECEPTACLE.
11. Plug in LIGHT WIRE (if applicable) and re-install grille that
were unplugged and removed in Step 2.
12. Turn on power to fan.
13. Go to “Bluetooth
OPERATION” section for speaker operating instructions.
®
wireless technology SPEAKER
RECEPTACLE
MODEL SPKACC
Bluetooth
®
wireless technology
SPEAKER OPERATION
To connect to the Broan-NuTone Bluetooth® wireless technology Speaker for the rst time:
1. To play your personal music or audio files, you need a Bluetooth wireless technology enabled
Smart Phone, Tablet, or any other such device.
2. Set your device to a low-to-midrange volume before connecting to the speaker.
3. Make sure Fan is ON and Bluetooth
meters (approximately 33 feet) of the Speaker/Fan.
4. Pairing your Bluetooth
a. For iPad/iPhone/iPod touch:
i. From your iPad/iPhone/iPod touch home page, tap Settings.
ii. From Settings, tap General (if you have iOS 7 or greater, you can skip this
iii. From General, tap Bluetooth.
iv. Move the Bluetooth
v. The Broan-NuTone Speaker has the Bluetooth
vi. Tap on “Sensonic™ Vent Fan” to complete the pairing of the Bluetooth
b. For Android Phone/Tablet:
i. From your smart phone/tablet home page, tap Settings.
ii. From the Settings menu, go to Wireless & Controls, Wireless & Networks, or
iii. Find Bluetooth
iv. On the Bluetooth
v. The Broan-NuTone Speaker has the Bluetooth
vi. Tap on “Sensonic™ Vent Fan” to complete the pairing of the Bluetooth
c. For all other Bluetooth
i. Follow the instructions that came with your Bluetooth
ii. Most Bluetooth
iii. The Broan-NuTone Speaker has the Bluetooth
5. Open up the audio program on your device and play your music or other audio files. The audio
file should play over the Bluetooth
6. When done playing/listening to your audio files, disconnect from the Speaker by either turning
OFF the fan, disconnecting Bluetooth
Tablet, etc) or simply walking away. The Bluetooth
disconnect when the device is out of range of the Speaker, which should occur when device is
approximately 10 meters (33 feet) away from the Speaker.
To connect to the Bluetooth
(after initial connection is made):
1.
The Sensonic™ Speaker can only play audio files from one Bluetooth® wireless technology device at a time, therefore one device must be DISCONNECTED (but not necessarily UNPAIRED)
before using the Speaker with another device.
2.
If your Bluetooth® wireless technology device was DISCONNECTED but not UNPAIRED from
the Speaker last time it was used, then it should automatically connect next time the device
is within range of the Speaker, unless the Speaker is already CONNECTED to another device.
a. If your device does not CONNECT automatically with the Speaker, then find your
“Paired Devices” or similar list and TAP on “Sensonic Vent Fan” to reconnect with
3.
4.
5.
the Sensonic™ Speaker.
If your Bluetooth® wireless technology device was UNPAIRED from the Speaker after the last
time it was used, you must follow the connection procedure in the previous section for PAIR-
ING your device with the Speaker.
Open up the audio program on your device and play your music or other audio files. The audio
file should play over the Bluetooth
When done playing/listening to your audio files, disconnect from the Speaker by either turning
OFF the fan, disconnecting Bluetooth
Tablet, etc) or simply walking away. The Bluetooth
disconnect when the device is out of range of the Speaker, which should occur when device is
approximately 10 meters (33 feet) away from the Speaker.
®
wireless technology enabled device with the Speaker:
step).
this, a list of discoverable Bluetooth
Fan”. This identifier should be in the list of Discoverable Devices. If not,
turn the Fan OFF, then ON, then turn Bluetooth
• If “Sensonic™ Vent Fan” is still not on the list, consult with the owner’s
manual for your device and follow the procedure for Pairing/Connecting
a Bluetooth
less technology Speaker with your Apple device.
something similar.
or move Bluetooth
something similar.
Fan”. This identifier should show up in the list of Available Devices. If not,
turn Fan OFF, then ON, and repeat pairing procedure.
• If “Sensonic™ Vent Fan” is still not on the list, consult with the owner’s
manual for your Android device and follow the procedure for
Pairing/Connecting a Bluetooth
less technology Speaker with your Android device.
enabled Phone, Tablet or Pad device to set it to search for Bluetooth
technology accessories.
the “Paired Devices” (or similar) screen and SELECT “Search for Devices” or
something similar.
Fan”. This identifier should show up in the list of Available Devices, Discoverable Devices or similar. If not, turn Fan OFF, then ON, and repeat pairing
procedure.
®
wireless technology Speaker each subsequent time
®
wireless technology enabled device is located within 10
®
Slider to ON/green (if it isn’t ON already). When you do
®
wireless technology device.
®
, Bluetooth® Settings or something similar and tap Bluetooth
®
Slider to ON (if it isn’t on already).
®
screen, tap “Scan for Devices”, “Search for Devices” or
®
wireless technology enabled devices:
®
wireless technology enabled devices will require you to go to
®
Fan Speakers.
®
wireless technology from your device (Smart Phone,
®
wireless technology Fan Speakers.
®
wireless technology from your device (Smart Phone,
®
wireless technology devices will appear.
®
identifier “Sensonic™ Vent
®
OFF, then ON.
®
wire-
®
identifier “Sensonic™ Vent
®
device.
®
wireless technology
®
identifier “Sensonic™ Vent
®
wireless technology will automatically
®
wireless technology will automatically
®
wire-
®
wireless
Page 4
®
View other RV hardware made by NuTone on our website.
Loading...