NuTone LA522WH, 99526440A User Manual

INSTALLATION INSTRUCTIONS

READ & SAVE THESE INSTRUCTIONS

WIRELESS DOOR CHIME

THIS PACKAGE INCLUDES:

• Wireless Door Chime - requires 3 “D” alkaline batteries (not inlcuded)

• Wireless Door Chime Pushbutton & 12-volt alkaline battery

• Mounting Hardware

FEATURES

• Battery powered chime and transmitter - no wires to run

• Adjustable volume control

• 125-foot open air operating range

• 64 frequency channels to minimize interference from other devices

• Optional NuTone wireless pushbuttons available for multiple doors (side, rear, etc.)

INSTALLATION

1. Install chime batteries.

Remove the back of the chime case and install three 1.5V alkaline, size “D” batteries (not included). Replace back case.

FRONT

CASE

NOTCH

BACK

PLATE

3. Select chime melody.

Use the door set jumpers on the pushbutton(s) to change the chime melody. Tip: Multiple pushbuttons can be set to ring a different melody for each door (up to three melodies).

BATTERY

PUSH

BUTTON

{

DOOR SET

JUMPERS

Put jumpers on pins y and x for Westminster chime.

2. Install pushbutton battery.

Open the pushbutton case and install the 12V alkaline battery (included).

To open pushbutton case: Insert a at-blade screwdriver into the notch on the bottom and push to open. Lift the front case up and away from the back plate.

Put jumpers on pins y and * for 2note “ding-dong”.

Put jumpers on pins x and * for 1note “ding”.

1 6

4. Test the operating range.

Place the chime and pushbutton in their desired locations and press the pushbutton. If the chime sounds, proceed to step 5. If the chime does not sound, refer to the “Troubleshooting” section for help.

5. Install the chime.

Use the hardware (provided) to mount the chime on a wall. The chime can be mounted by using the holes in the back of the case or by using 2 screws with the keyholes. Snap the front of the chime case back on.

Keyholes

Close chime case from bottom

6. Install pushbutton.

Use the hardware (provided) to attach the back plate of the pushbutton to its mounting surface. Make sure the long tab is at the bottom.

If mounting the pushbut-

BACK

PLATE

ton to a metallic or concrete surface: Increase the operating range by using wood spacers between the back plate and the mounting surface.

Snap the pushbutton case onto the back plate.

7. Check operation.

Depress pushbutton and listen for chime. If necessary, adjust volume using the control on the back of chime. If chime does not function properly, refer to “Troubleshooting” section.

Chime Volume Control

BATTERY REPLACEMENT

Chime

Open chime case. (see step 1) Replace batteries with three 1.5V alkaline, size “D” (R20) batteries. Close chime case.

Pushbutton Open pushbutton case (see step

2). Replace battery with one 12V alkaline, type A23 (Model RCA23), or MN21 battery. Close pushbutton case.

ADDITIONAL DOOR CHIMES

Additional wireless door chimes can be set to ring separately from or together with other wireless door chimes. Set the pushbutton and chime frequency codes accordingly. See page 3.

LONG TAB

TROUBLESHOOTING

1 6

The range of the door chime depends on location, temperature and battery condition. If you are having problems with this product, please try the solutions listed below.

Chime rings on its own:

• Button frequency jumpers and chime frequency jumpers

MUST BE SET TO THE SAME

FREQUENCY CODE. Change the button frequency jumpers and chime frequency jumpers to a different code.

BATTERY

PUSH

BUTTON

{

Button Frequency Jumpers

(inside pushbutton case)

Chime Frequency Set Jumpers

Batteries are OK, but chime does not work when installed:

• Mounting the chime or button directly on metal, concrete or near metal studs reduces the range. Use 1/4” to 1/2” wood shims to move the chime or doorbell button off of the surface.

• Do not mount the chime too close to ground level concrete slabs which may also reduce the range. Mount the chime away from the

oor.

• Try different locations for the chime closer to the button. Also, try to orient the chime at a different angle to increase the range. Range is most effective to the sides of the button.

Chime doesn’t sound:

• Make sure the button and the chime are set to the same frequency code.

• Replace the button battery. Also check chime batteries.

FREQUENCY CODE

- SAMPLE SETTING -

Button Frequency Jumpers

(Jumpers removed (OFF) from 2, 4, 6)

Chime Frequency Jumpers

(Jumpers removed (OFF) from 2, 4, 6)

Regulatory Information The user is cautioned that changes or modications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause

harmful interference, and

2. This device must accept any

interference received, including interference that may cause undesired operation.

One Year Limited Warranty

WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this one year period, NuTone will, at its option, repair or replace, without charge, any

product or part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by NuTone), faulty installation or installation contrary to recommended installation instructions.

The duration of any implied warranty is limited to the one year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow

the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.

WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the address stated below or telephone 1/800-543-8687, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date.

Date of Installation Builder or Installer

Model No. and Product Description

IF YOU NEED ASSISTANCE OR SERVICE:

For the location of your nearest NuTone Independent Authorized Service Center:

Residents of the contiguous United States Dial Free 1-800-543-8687

Please be prepared to provide:

Product model number • Date and Proof of purchase • The nature of the difficulty

Residents of Alaska or Hawaii should write to: NuTone Inc. Attn: Department of National Field Service, 4820 Red Bank Road, Cincinnati Ohio 45227-1599. Residents of Canada should write to: Broan-NuTone Canada, 1140 Tristar Drive, Mississauga, Ontario, Canada L5T 1H9.

Rev. 03/2001

WARRANTY

99526440A

+ 8 hidden pages