Nutek NTRSA User Manual
4 Button / 1 Way Remote Start Systems
4 Button / 1 Way Remote Start Systems
QUICK START OPERATION GUIDE
Visit www.CarAlarm.com today
To Download your complete operation guide and learn more about:
Additional Features
- Anti-Carjacking Mode
- Secure Code Override
- Turbo Timer Support & Operation
System Upgrades
- Linkr Smartphone Control
- 2-Way Controllers w/ Extended Range
- Upgrading To Full Security With Sensors & Siren
Problems? Questions? Contact Customer Service:
800-554-4053 (toll free) | +1-770-942-9876 (outside USA)
This device complies with FCC Rules part 15. Operation is subject to the following two conditions: 1) This device may not cause
harmful interference &, 2) This device must accept any interference that may be received, including interference that may cause
undesired operation.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment.
Such modications could void the user’s authority to operate the equipment.
- Customizing System Options
- Passive Security Functions
- Emergency Override
/omegard
Copyright 2018 Omega Research & Development Technologies, Inc. QOM_4BUT1WAY_20190315
Scan to register &
download the full
operation guide at
CarAlarm.com!
/c/omegard
Your System Model:
(Installer, write system model above)
QUICK START OPERATION GUIDE
REPLACING YOUR REMOTE BATTERY
STEPS REMOTE PART# BATTERY (QTY)
1) Find the part # on the back of the remote to identify the battery.
2) Remove the screw from the back of the remote
3) Gently pry the case in halves apart to access & replace the battery.
SECURITY*, KEYLESS ENTRY, & CONVENIENCE FUNCTIONS
FUNCTION BUTTON(S) NOTE
Security enabled systems will flash the status LED.
Ideal for occupied vehicles, RV’s, etc.
If only driver’s door unlocks, press again to unlock all
System will toggle Arm/Disarm each time
x 2
Sensors are disabled until you Lock/Arm again.
By default, the system will also disarm/unlock
Doors will Lock or Unlock before panic.
Supported Antenna Models:
REC-1N4 REC-2N4-3D
REC-2N9-3D RFK-X2-2N9
Lock & Arm*
Lock Only*
Unlock & Disarm*
Silent Arm/Disarm*
Disable Sensor*
Trunk/Hatch Release
Panic
*Security related functions only available on some models. Consult your installer to upgrade.
,
,
For 3 Sec.
or 3 Sec.
Register today at www.CarAlarm.com
to activate/learn about your warranty & download a complete operation guide.
1412 & 1417 CR2032 (1)
1415 & 1418 CR2016 (2)
14
4 Button / 1 Way Remote Start Systems
4 Button / 1 Way Remote Start Systems
QUICK START OPERATION GUIDE
REMOTE START FUNCTIONS
FUNCTION BUTTON(S) NOTE
Engine Start/Stop
Run Time Extender
Low Battery & Low/
Hi Temp Auto-Start
Remote Valet
FUNCTION VALET BUTTON NOTE
Pit Stop Mode Press 2x w/ Engine Running
XL Pit Stop Mode Press 6x w/ Engine Running
MANUAL TRANSMISSION RESERVATION MODE
This must be performed before you can remote start a manual transmission vehicle to ensure
the car is in neutral & maximum safety. Consult your installer for more information.
1) With the engine running by key, hold the brake pedal & place the transmission in neutral.
2) Apply the parking brake and release the brake pedal.
3) Send the remote start command via your remote. The remote start should engage
(not crank) and the status LED will begin flashing.
4) Take the ignition key out of the switch (the engine should stay running).
5) Exit the vehicle and lock your doors with the remote. The engine will turn off.
x 2
, ,
, , +
Activation is programmable (contact installer). Take Over: Turn ignition key ‘ON’ (not start), press brake pedal
The system will restart the internal run timer.
Auto-start will activate a max of once per 2 hours. See your installer or the full manual for threshold settings.
This disables remote start and the security system. The status LED will turn on. Repeat this process or press valet
button once to exit valet mode. TIP: You can also enter valet mode by holding the valet button for 3 seconds!
This will leave the engine running for the programmed run time so you can take your keys with you to run errands.
This will leave the engine running for 12 hours so you can safely leave the engine running for extended periods.
Ideal for commercial vehicles using strobes, refrigerators boxes, etc.
WINDOW-MOUNT ANTENNA/RECEIVER
QUICK START OPERATION GUIDE
AUXILIARY REMOTE FUNCTIONS
FUNCTION BUTTON(S) NOTE
CH3/AUX1 - Write function in rst column*
+
*These special functions may not be available on your vehicle. Consult your installer.
PROGRAMMING REMOTES TO THE SYSTEM (UP TO 4)
BEFORE YOU BEGIN: Have all remotes for the system at hand.
1) Turn the ignition key “ON” (do not start).
2) Press the valet button 5 times within 5 seconds of step 1.
- The horn will briefly sound
3) Press & release the “lock” button on each transmitter one after the other.
- 1-button models, press the “start” button.
- The siren/horn will chirp once for each transmitter.
- NOTE: When the rst remote is learned all previous remotes are erased.
- NOTE: All other button functions will automatically be assigned.
4) Turn the ignition key “OFF”.
- NOTE: The system will exit at any time
Status LEDValet / Programming Button
after 10 seconds of no activity.
CH4/AUX2 - Write function in rst column*
+
CH5/AUX3 - Write function in rst column*
+
AUX4 - Write function in rst column*
+
SCAN TO WATCH
HOW-TO VIDEO
REMOTE START ERRORS
CHIRPS/FLASHES VIOLATED ZONE
LED ON System in Valet mode
1 Hood opened
2 Brake pedal pressed
3 Bad tach signal or engine over-rev.
4 BLACK/WHITE wire lost ground
5 3D motion detected while cranking
6 Received engine stop command
7 Alarm was triggered
8 Run time expired
9 Low vehicle battery voltage detected
If the system fails to remote start or remote start stops
unexpectedly, it will give a long horn/siren chirp followed by a
series of short horn/siren chirps & light flashes. The short chirps/
light flashes indicate the cause of the failure.
TIP: If remote start won’t activate, the system may be in valet
mode (Status LED ON). Press the valet button once to exit.
32
Loading...