Nutek MTIB Users Manual
7
Flash Function
1 Flash System is Armed
2 Flashes System is Disarmed
3 Flashes Disarmed / Triggered
3 or 6 Flashes Car Locator
Constant On or Flashing Under Remote Start
Chirp Function
1 Chirp System is Armed
2 Chirps System is Disarmed
3 Chirps Ajar Warning
4 Chirps Disarm / Triggered
2,3,6 Chirps Progressive Car Locator
Siren/Horn
LED Doors
Starter Dome Light
1. Arming 1 or 3 Chirps 1 Flash Slow Flash Locking
Disabled
(Option)
2. Disarming 2 or 4 Chirps
2 or 3
Flashes
Unlocking
Turns on for
30 Seconds
3. Trigger Alarming Flashes Slow Flash
Disabled
(Option)
Flashes
4. Panic Alarming Flashes Flashes
5.Car
Jacking
Alarming Flashes
Disabled
(Option)
Flashes
6.Car
Locator
2,3,6 Chirps 3,6 Flashes
Parking Light Indicators
Chirp Indicators
System Characteristics
Parking
Light
PLUS6900-UM.qxp 4/3/2009 1:18 PM Page 7
8
1. Press the button on the transmitter.
2. The siren will chirp once and parking lights will flash once indicating that the system is now
armed. The vehicle door will lock upon arming when interfaced with the security system.
Ajar Warning:
If the siren sounds 3 chirps,
then you have left a door,
trunk, or hood lid ajar.
Silent Arming/Disarming
Press the transmitter and button at the same time to arm or disarm your security system. No
chirp sound will be heard. The arm/disarm confirmation will be through the vehicle’s parking
lights only.
Shock Sensor Bypass
Press the button on the transmitter two times within 3 seconds. This will arm the security
system and bypass the shock sensor. The system will chirp one additional time to confirm the
sensor Bypass Mode was activated. The sensor bypass feature is programmed to activate for one
arming cycle only. The security system will return to normal operation during the next arming
cycle.
Hidden Alarm Function
Press the button first, within 3 seconds press the button to activate the hidden alarm
function. The security system will arm, but the siren / horn will be silenced even if the sensor is
triggered in the armed status.
Manual arming/disarming is controlling your security system via the remote transmitter. This
security system is equipped with an optional Automatic Arming feature which allows the security
system to arm 45 seconds after the last door is closed. Operation is as follows:
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 45 seconds. If you
reopen any Door, Hood, Trunk the security system LED will stop flashing. It will begin flashing
again once the vehicle’s entrances are closed.
3. After the 45-second timer has elapsed, the security system will automatically “ARM”. The
siren/horn will chirp once, and the parking lights will flash once.
Automatic Arming with Automatic Door Locking (Programmable)
If this feature has been programmed on, the vehicle doors will automatically lock after the
automatic arming cycle has been completed.
System Armed Door Ajar Trunk/Hood Ajar
Manual Lock/Arm
Automatic Arming
PLUS6900-UM.qxp 4/3/2009 1:18 PM Page 8
9
Automatic Arming Bypass
While the system is in Disarmed Mode, press the button twice. The horn/siren will respond
with one chirp and the LED will turn “ON”. The security system will remain in this mode for as
long as you wish. To exit this mode press the or buttons and the system will return to
normal status.
1. Press the button on the transmitter.
2. The siren will chirp twice and parking lights will flash twice indicating that the system is now
disarmed. The vehicle door will unlock and the dome light will turn on for 30 seconds upon
disarming when interfaced with the security system.
Tamper Disarming
If the security system was triggered prior to disarming, the siren will chirp 4 times and the
parking lights will flash 3 times. One of the enclosed panels will be displayed on the LCD
transmitter screen to indicate which sensor had been triggered
Pathway Illumination
This feature turns the parking lights “ON” for 30 seconds upon a unlock signal and for 10
seconds upon the lock signal.
Two Step Door Unlock
This feature will independently unlock the driver’s door only when disarming the security
system. Pushing the button a second time within 3 seconds will unlock the other doors.
Automatic Rearm
If this feature is selected, the security system will automatically rearm itself within 60 seconds
after disarming with the remote transmitter. Automatic rearm will cancel if any door is opened
before the 60 second timer is up.
The override function may be used if the remote transmitter is lost or inoperative. Override can
be done without password/pin number (this is the factory default setting).
1. Enter the vehicle and turn the ignition switch to “ON” position (alarm will sound).
2. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enter
the Disarm Mode. You can now start and operate the vehicle normally.
Manual Un-Lock / Disarm
Disarming without a Transmitter
Automatic Arming
(Continued)
Shock Sensor Triggered
Doors Triggered
Trunk/Hood Triggered
Ignition Triggered
PLUS6900-UM.qxp 4/3/2009 1:18 PM Page 9
10
Manual valet mode allows you to bypass all alarm functions eliminating the need to hand your
transmitter to parking attendants or garage mechanics. This mode is also a necessity if your
transmitters become in-operable. When the system is in Valet Mode, all alarm functions and
remote start functions are off. However, the remote panic feature and remote door locks remain
operational. To enter the Manual Valet Mode, the system must first be disarmed either by using
your remote transmitter, or by operating the manual override sequence.
Enter Valet Mode
1. When in Disarmed Mode, turn the ignition to the “ON” position.
2. Push and hold the valet switch for 2 seconds. The LED will flash every 5
seconds as long as the unit is in the Valet Mode.
Note: When the unit is in valet mode, the LCD transmitter icon will be
displayed
Exit Valet Mode
1. To return to normal operation, turn “ON” ignition.
2. Push and hold valet switch for 2 seconds. The LED will stop flashing, indicating the system has
now exited the Valet Mode.
Note: When the unit is out of valet mode, the icon will be off and you will hear
a short melody from the transmitter..
RF valet mode provides the same functions as manual valet mode but allows you to enter and exit
the valet mode using the remote transmitter. When the system is in Valet Mode, all alarm
functions and remote start functions are off. However, the remote panic feature and remote door
locks remain operational. To enter/exit the RF Valet Mode, repeat the following procedures.
Enter Valet Mode
1. In Disarmed Mode, open the drivers door.
2. Push and hold the and transmitter buttons until the door locks cycle “Lock then Unlock”.
The LED will flash every 5 seconds to indicate that the unit is in the Valet Mode.
Note: When the unit is in valet mode, the LCD transmitter icon will be displayed
Exit Valet Mode
1. In Unlocked Mode, open the drivers door.
2. Push and hold the and transmitter buttons until the door locks cycle “Lock then Unlock”.
The LED will stop flashing every 5 seconds to indicate that the unit is out of the Valet Mode.
Note: When the unit is out of valet mode, the LCD transmitter icon will be off and you will hear
a short melody from the transmitter.
Note: The remote vehicle location system is active 30 seconds after the alarm is armed.
1. Press the button to active the vehicle locator system. The horn/siren will beep 2 times and
the parking lights will flash 3 times. This operation will repeat a second time.
2. Press the button again within 30 seconds. The horn/siren will beep 3 times and the parking
lights will flash 3 times. This operation will repeat a second time.
Hold 2 Seconds
Manual Valet Mode
RF Valet Mode
(Applies to All Transmitter Types)
Progressive Remote Vehicle Locator System
PLUS6900-UM.qxp 4/3/2009 1:19 PM Page 10
The transmitter can be used as a remote panic switch to manually trigger the alarm system in
case of an emergency.
1. Press and hold the button for 3 seconds to enter the Panic Mode (horn/siren will start to
sound and parking lights will flash).
2. While in Panic Mode the transmitter and buttons can be used to lock and unlock the door
(if that option is installed). However, if the button is pressed, the vehicle’s starter disable
device (when installed) will be disabled, allowing the vehicle to start.
3. To turn off the panic function, press and hold the button again for 3 seconds or press and
release the or buttons.
4. If the panic function is not turned off by the transmitter, it will turn off and reset itself after 30
seconds.
11
Panic Feature
The Security System has a unique feature for using your vehicle’s dome light:
1. Upon disarming the vehicles security system, the interior dome light will remain on for 30
seconds.
2. If the security system is triggered, the dome light will flash for the same duration as the
horn/siren.
Note: Turn “ON” the ignition switch or arm the system to turn off the dome light.
Domelight Supervision
If the vehicles door locks have been interfaced with the security system, the system will
automatically lock the doors 3 seconds after the ignition is turned “ON”, or unlock the doors when
ignition key is turned “OFF”. Note: If a protected entrance is open, the doors will not lock.
Press and hold the button for up to 3 seconds to activate the trunk release (Channel 3 output)
and/or any other devices connected.
Press and hold the and button at the same time to activate the Channel 4 output. Channel 4
is user programmable timer output. You may program the built-in timer to send a ground signal
for any time duration from 1 second to 120 seconds. For example, this timer output may be used
to turn on the headlights, power window or sunroof (Factory defaults setting at momentary
output.)
Ignition Key Controlled Door Lock/Un-Lock
Channel #3 Trunk Release Output
Channel #4 Timer Controlled Output
Progressive Remote Vehicle Locator System (Continued)
3. Press the button again within 30 seconds. The horn/siren will beep 6 times and the parking
lights will flash 6 times.
PLUS6900-UM.qxp 4/3/2009 1:19 PM Page 11
Loading...