Nutek ATRB User Manual
1 2
Lock Button
Press once to lock and arm alarm.
Press and hold 3 seconds for panic
alarm where applicable
Unlock Button
Press once to unlock and disarm alarm
Press and hold 3 seconds for panic
alarm where applicable.
Trunk / Start Button
Press two times in succession to
start vehicle. Press and hold for
3 seconds for Trunk Release where applicable
OPTION 1
Press and release to activate
option 1 where added
OPTION 2
Press and release to activate
option 2 where added
Model PR2LED
Operators Manual
RF Upgrade Kit
Check with your installation center for features and functions operational on your system.
To Operate System:
1) Press the lock button to lock the doors and arm the alarm if installed. The LED alongside the
lock button will ash and the transmitter will beep once when the vehicle receives and responds
to the command.
2) Press the unlock button to unlock the doors and disarm the alarm if installed. The LED along-
side the unlock button will ash and the transmitter will beep twice when the vehicle receives and
responds to the command.
3) Press and hold the Trunk/Start button for 3 seconds to unlock the trunk. The LED alongside
the button will ash when the vehicle receives and responds to the command.
4) Press the Trunk/Start button two times in succession to start the vehicle a melody will sound
upon start. The vehicle will start and run the predetermined time set up during installation (5 to
60 minutes selectable). During this run cycle, the LED alongside the button will ash 1 time every
10 seconds indicating the vehicle is in fact running.
Anytime during the run cycle, enter the vehicle by rst unlocking the doors with your transmitter,
insert your key and turn it to the run, NOT START, position, then step on the brake, the vehicle is
now in control of the ignition key the transmitter will sound a shut down / owner take over melody.
NOTE: For push to start vehicles contact your installation center for proper procedure
.
PATENTED: www.voxxintl.com/company/patents
128-9486
Page 1
Consult your installation center for operation and information on convenience options 1 & 2
which may have been connected or added to your vehicle.
Quick Stop Mode:
With vehicle running, if you wish to make a quick stop and leave the vehicle running, once you
arrive at your destination:
a) Place the gear selector in Park,
b) Set the parking brake,
c) With your foot OFF the brake, press the transmitter button two times in succession.
The vehicle will now be under control of the remote start system. Turn your ignition switch o,
WITHOUT, stepping on the brake, and exit the vehicle. Lock the doors with the key to insure
security.
(Alarm Systems Only) PUSH-BUTTON LED RECEIVER VALET/OVERRIDE/SAFETY SWITCH
The Push-Button LED switch located in the receiver allows you to temporarily bypass all alarm
functions, eliminating the need to hand your transmitter to parking attendants or garage mechanics.
When the system is in valet mode, all alarm functions are bypassed, however the remote panic
feature and remote door locks will remain operational. To use the valet mode, the system must
rst be disarmed either by using your keychain transmitter, or by activating your personalized
manual override code.
1. Enter the vehicle, and turn the ignition key to the on position.
2. Press and hold the Push-Button switch until the LED turns on solid. The system will remain in
the valet mode.
3. To return to normal operation, press and release the Push-Button switch any time the ignition is
on.
NOTE: Always remember to return the vehicle to the valet o position. This will ensure that the
vehicle remains protected at all times.
(Alarm Systems Only) MANUALLY OVERRIDING YOUR SYSTEM:
USING THE RECEIVERS PUSH-BUTTON OVERRIDE SWITCH
Your Security System can be disarmed without the use of the keychain transmitter. This is necessary,
since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. If
your system has been selected for Valet Switch manual override as indicated on the last page of
this manual, to bypass the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the on position.
3. Within 5 seconds, press and release the push-button override switch.
The alarm system will stop sounding and enter the (bypassed) mode. You can now start and
operate the vehicle normally.
Typically this override mode is used only if the transmitter has become inoperative.
(Alarm & Keyless Systems Only) PROGRAMMING YOUR CUSTOM OVERRIDE CODE
Unlike override switches easily found, and defeated, this security system allows the consumer to
program a personal override code, oering a higher level of security. To take advantage of this option,
programmable feature # 9 must be selected for the Custom Code Option. Consult your installation
center for programming details. The system comes from the factory with a preprogrammed override
code of 11. To change this default override code, do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency override sequence.
Turn the ignition switch to the on position.
2. Within 10 seconds, press and release the Receivers push-button switch, 3 times.
3. Within 10 seconds turn the ignition switch o, on, o, on, o, on. (The siren or horn will beep
and the lights will ash one time.)
Page 2
128-9486
Page 2
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and releasing the Receivers
push-button switch from 1 up to 9 times.
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch o then on.
6. Within 10 seconds, begin to enter your chosen units digit by pressing and releasing the Receivers
push-button switch from 1 up to 9 times.
7. Finish by turning the ignition switch to the o position. If the new code was accepted, the unit
will report back the newly entered code, by ashing the LED, rst indicating the 10ths digit,
pause and then the units digit. The unit will report the new code three times with a one second
pause between each code, then the system will begin arming. If the LED ash pattern reports the
previously stored code, the new code was not entered correctly. Please repeat steps 1 through
7 above considering the following.
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or
no digit entered in any place, units or tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned o for more then 5 seconds
during any of the above steps, the unit will revert back to the last successfully stored code.
CUSTOM CODE PROGRAMMING EXAMPLE
To Change the code from the factory preassigned code of 11 to “52” you would do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency override sequence.
2. Turn the ignition switch to the on position.
3. Within 10 seconds, press and release the Receivers push-button switch, 3 times.
4. Within 10 seconds turn the ignition switch o, on, o, on, o, on. (The siren or horn will beep
and the lights will ash one time.)
5. Within 10 seconds, begin to press and release the Receivers push-button switch to set the tenths
digit. (As per the example, press and release 5 times to set the tenths digit to 5)
6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch o then on.
7. Within 10 seconds, begin to press and release the Receivers Push-button switch to set the units
digit.
(As per the example, press and release 2 times to set the units digit to 2).
8. Turn the ignition switch to the o position. Immediately observe the LED ash pattern.
You will notice the LED ashing ve times, pause, and then ash two times, pause. This pattern will
be repeated three times indicating the new code (52) has been accepted and stored in memory.
NOTE: If after step 7, the LED ashes a code other than what was just entered, this indicates that
the code has not been changed. You will have to repeat steps 1 through 7 above being
certain to note the following:
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no digit
entered in any place, units or tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned o for more then 5
(Alarm Systems Only) MANUALLY OVERRIDING YOUR SYSTEM:
USING THE CUSTOM CODE OVERRIDE
Assuming the override code programmed has not been changed, and the default override code of
11 is in the system’s memory.
1) Enter the vehicle and turn the ignition switch to the on position.
NOTE: The siren will sound.
seconds during any of the above steps, the unit will revert back to the last successfully
stored code.
Page 3
128-9486
Page 3
Loading...