Nutek ATIC User Manual
TRANSMITTER PROGRAMMING GUIDE
Model : APS 95 BT3 & 09BT3
The transmitters included with the security system have been pre - programmed
at the factory, with each button pre-assigned to control a specific function of
the security system. Although the security system in the vehicle has either 3
or 4 channels (RECEIVER) depending on the model, the transmitters included
with the system are 7 channel transmitters. This allows you to program each
transmitter to more than one vehicle in two car families, and also allows you to
change which button(s) control certain functions of the system. (Example:
Transmitter channel 5 can be programmed to activate Receiver channel 2.) Refer
to the chart below for access to each of the transmitter channels, and for the
standard factory button assignments.
TRANSMITTER SYSTEM RECEIVER
CHANNEL BUTTONS CHANNEL FUNCTION
1 1 1 Remote Arm & Disarm
2 2 2 * Pulsed Output for Accessories
3 3 3 * Switched Output for Accessories
4 2 & 3 4 * Switched Output for Accessories
51 & 2- 61 & 3- 7 1, 2, 3 - -
* Some of the more common accessories for these additional channels are;
AS 9076N Remote car starter
AS WRP Remote window roll up
AS 9256 Remote trunk release relay
Remote Emergency Panic
Remote Door Lock & Unlock
128-4619A
1 of 12
Released (ENGLISH ONLY) 8-15-95.
Released French & Spanish. 10-31-95.
Rev A to include 09BT3 9076 & ASWRP 06-30-09
PROGRAMMING THE TRANSMITTERS
It is important to remember that during programming, each individual step of
the procedure must be executed within 15 seconds of the previous step.
When the 15 second time limit is allowed to expire, the system will
automatically terminate the programming mode. This is indicated by a long
chirp from the siren.
Additionally, the system will store codes from up to four different transmitters. If a 5th transmitter is programmed to any receiver channel, then the first
transmitter programmed to that channel will be erased from the system's
memory.
To program new or additional transmitters,
1. Enter the vehicle, and turn the ignition key to the " on " position.
2. Flip the valet switch on - off - on - off - on - then off.
3. The dash LED will flash one time, and the siren will chirp one time, indicating
the system is ready to accept programming for receiver channel 1.
4. Press and hold the selected transmitter button(s) until the siren sounds
a long chirp, indicating the signal has been stored into memory.
5. If you have additional transmitters (up to 3) that need to be programmed,
repeat step 4 for each transmitter.
6. Flip the valet switch on then off.
7. The dash LED will flash two times, and the siren will chirp two times,
indicating the system is ready to accept programming for receiver
channel 2.
8. Press and hold the selected transmitter button(s) until the siren sounds
a long chirp, indicating the signal has been stored into memory.
9. If you have additional transmitters (up to 3) that need to be programmed,
repeat step 8 for each transmitter.
10. Flip the valet switch on then off.
11. The dash LED will flash three times, and the siren will chirp three times,
indicating the system is ready to accept programming for receiver
channel 3.
12. Press and hold the selected transmitter button(s) until the siren sounds
a long chirp, indicating the signal has been stored into memory.
13. If you have additional transmitters (up to 3) that need to be programmed,
repeat step 12 for each transmitter.
14. Flip the valet switch on then off.
128-4619A
2 of 12
15. The dash LED will flash four times and the siren will chirp four times,
indicating the system is ready to accept programming for receiver
channel 4.
16. Press and hold the selected transmitter button(s) until the siren sounds
a long chirp, indicating the signal has been stored into memory.
17. If you have additional transmitters (up to 3) that need to be programmed,
repeat step 16 for each transmitter.
18. Turn the ignition key off. The siren will sound one short chirp then one
long chirp indicating the system has terminated the program mode.
TRANSMITTER BATTERY REPLACEMENT
You will notice a decrease in transmitter range as the battery condition
deteriorates. Transmitter battery replacement is recommended at least every
10 to 12 months, depending upon how frequently the transmitter is used.
The transmitter has a small red LED built into the case. This LED can be used
to indicate battery condition. If the LED does not illuminate, then the battery
is discharged, and must be replaced.
To replace the transmitter battery:
1. Remove the small phillips head screw from the bottom cover of the
transmitter.
2. Carefully unsnap the top cover of the transmitter from the bottom cover.
3. Remove the discharged battery, making note of the location of the + and
- contacts, and replace with a new type GP 23A 12 volt battery or CR2032
Lithium battery.
4. Replace the transmitter cover, taking care not to damage the LED or
switches on the circuit board, and secure with the small phillips head
screw.
This device complies with FCC Rules Part 15 Operation is
subject to the following two conditions
(1) This device may not cause harmful interference and
(2) This device must accept any interference that may be
received, including interference that may cause undesired
operation.
NOTE:The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority
to operate the equipment.
128-4619A
3 of 12
ORDER FORM FOR 3 BUTTON TRANSMITTER
MODEL NO. APS 95 BT3 & 09BT3
IMPORTANT : To help us expedite your order, please print all of the information
legibly, and mail this form and your payment according to the instructions
below.
1. Name : ___________________________________________________
Address : _________________________________________________
City : __________________ State : _______ Zip Code : ___________
2. Telephone Number : ( _______ ) _______________________________
3. Enter the total number of transmitters required here : _______________
4. The cost per transmitter is $ 65.00.
5. Enter the total amount enclosed here :
___________________________
( New York state residents must include the appropriate sales tax. )
6. Method of payment; check one of the boxes below.
Mastercard Visa Check or money order * ( do not send cash )
* Make checks payable to Audiovox Corporation
7. Credit Card Number : ________________________________________
8. Credit Card Expiration Date : _____________________
Credit card purchasers can order additional or replacement
transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and follow
the instructions from the operator interface.
9. Mail this form, and your check, to ;
Audiovox Corporation
150 Marcus Blvd.
Hauppauge, N.Y., 11788
Attn: TRANSMITTER DEPARTMENT
Form No. 128-4619A
128-4619A
4 of 12
Loading...