3in13in1
USER MANUAL
ecosphere
™
water purifier
2
TABLE OF CONTENTS
System Components 3
Function Overview 4
How to Set up Your Purifier 6
in Cartridge Set Up 7
Initial Run 8
Use 8
Purified Water 8
Tap Water 8
Replacing in Cartridge 9
in Cartridge Replacement Cycle 10
in Cartridge Replacement 10
Maintenance 11
Troubleshooting 11
Precautions 12
Main Specifications 14
Replacement and Warranty Information 14
3
SYSTEM COMPONENTS
3in13in1
EcoSphere Water Purifier
Faucet Attachment
Faucet Adapter Kit
3in1 Cartridge
(
inside EcoSphere Water Purifier)
Top Lid
4
FUNCTION OVERVIEW
Tap Wate r
Purified Water
Blue Light: Tap water in use.
Blue Light: Purified water in use.
Orange Light: Purifier is powering
on; purifier has not been used for 72
hours; 3in1 cartridge’s life cycle has
expired.
Flashing Orange Light: Water
temperature is too high.
5
3in13in1
Maintenance Light Indicator: When light is orange,
the water purifier needs repair.
Power Light Indicator: When light is blue, water
purifier is on.
3in1 Cartridge Light Indicator: When light is
orange, the 3in1 cartridge must be replaced.
3in1 Reset: After installing a new 3in1 cartridge, hold
for three seconds to reset the water purifier. This
ensures that the lifespan of the 3in1 cartridge is
accurately tracked.
3in1
6
HOW TO SET UP YOUR PURIFIER
If the aerator has a glossy exterior, simply unscrew it by hand.
pro tip: Use a towel to increase friction.
If the aerator is firmly attached, use the small
wrench provided.
pro tip: The small wrench is specifically designed
to remove aerators and install the EcoSphere Water
Purifier faucet adapters.
Make sure to also remove the washer above the aerator.
note: These faucets are not recommended for use with the EcoSphere Water Purifier.
Shower heads Spout outlets wider than 24 mm
Square spout outlets Spout outlets shorter than 15 mm
Oval spout outlets Retractable faucets
REMOVING THE FAUCET AERATOR
what is the aerator?
Most faucets contain a removable aerator that helps mix water and air so that the flow of water is
consistent.
note: Some old faucets do not have aerators.
Faucet Aerator
Remove/Install
Faucet Ada pter
7
in CARTRIDGE SETUP
Remove plastic wrap from the 3in1 cartridge.
Insert the 3in1 cartridge gently into the water purifier, as shown
in figure 1.
Gently press and turn 3in1 cartridge 90˚ clockwise.
Align dot with lock icon (figure 2).
Make sure cartridge top is flush with the surface of the water
purifier (figure 3).
After the new 3in1 cartridge is securely in place, let water run
through the water purifier until the water comes out clear to prepare
the 3in1 cartridge for normal use (figure 4).
note: Letting the water run until clear cleans the 3in1 cartridge and
its tubing. Water will initially come out greyish-black or soapy.
This is normal.
Select the appropriate adapter from the
Faucet Adapter Kit.
Use the small wrench to securely
attach the adapter to the faucet.
pro tip: Make sure to match the appropriate
faucet thread to avoid water leaks.
ATTACHING THE FAUCET ADAPTER
Using the small wrench, attach the appropriate adapter so that it fits tightly.
Hold the faucet attachment with one hand, and then gently
push the faucet attachment onto the adapter while holding
the faucet with your other hand. Stop when you hear the
faucet attachment click into place.
To detach the faucet attachment from the faucet, hold the
faucet firmly with one hand and the faucet attachment with the
other hand, then pull down to remove the faucet attachment.
figu re 1
9:00
12:00
figu re 2
figu re 3
figu re 4
car tridg e flush wi th surfac e
9:00
RESET
8
INITIAL RUN
Touch the “Purified Water” button. The LED light will show orange.
Turn on the water faucet.
Let the water run through the water purifier until the water is clear to
prepare the 3in1 cartridge for normal use. The LED light will change to
blue once the water purifier is ready for use.
not e: Letting the water run until clear cleans the 3in1 cartridge and its
tubing. Water will initially come out greyish-black or soapy. This is normal.
USE
The faucet attachment has two outlets—one for tap water and the
other for purified water.
Tap water
Purified water
PURIFIED WATER
Touch the “Purified Water” button. A blue LED light will indicate
your selection.
Turn on the faucet to dispense purified water.
precautions:
• The water purifier will switch to tap water if water temperature is over 38˚C
to protect the life cycle of the 3in1 cartridge.
• Water flow will reduce if the purifier is run in conjunction with lower water
temperature and pressure. If LED light shows orange, let the water run
through the water purifier until the LED light changes to blue.
• The device will automatically switch to tap water mode if the faucet is
turned o for more than 10 seconds.
TAP WATER
standby mode: Touch the “Tap Water” button to switch to tap water.
You can alternate between tap water and purified water mode by
pressing either button.
When using “Tap Water” mode, water temperature is irrelevant.
+
+
9
REPLACING in CARTRIDGE
When the 3in1 light indicator starts flashing orange, it means that the 3in1
cartridge will need to be replaced soon.
When the 3in1 and Purified Water light indicators remain orange, it is time
to replace the 3in1 cartridge.
PURCHASING 3in1 CARTRIDGES
There are two ways to purchase replacement 3in1 cartridges:
• Order online at www.nuskin.com
• Purchase at your local Nu Skin Distributor Center
10
in CARTRIDGE REPLACEMENT CYCLE
3in1 Cartridge
level name function capabilities
replacement
cycle
I
Polyprophylene
PP
Pleated Prefilter
Removes large impurities
and particles
Rust, sand, fibers, and
other visible particles
12 monthsII
Compressed
Carbon Block
Filters odors, residual
chlorine, and some
organic compounds
Heterochromatic, odor,
chlorine,
methylene chloride, and
carbon tetrachloride
III
Polyether
Sulfone (PES)
Membrane
Filters up to 0.01
µm Bacteria, colloids, and rust
notes: The replacement cycle is a recommended cycle. The replacement cycle will vary depending
on your country and region, water quality, season, and frequency of usage.
in CARTRIDGE REPLACEMENT
After turning o the faucet, wait two minutes before removing the
3in1 cartridge.
Gently press and turn the old 3in1 cartridge 90˚ counter-clockwise (figure 1).
With the water o and the cartridge in the unlocked position, carefully lift
the cartridge out of the purifier (figure 2).
Follow the directions for cartridge setup on page 7.
Reset the water purifier by holding the “3in1 Reset” button for three
seconds (figure 3).
After the new 3in1 cartridge is securely in place, let water run through the
water purifier until the water comes out clear to prepare the 3in1
cartridge for normal use.
note: Letting the water run until clear cleans the 3in1 cartridge and its tubing.
Water will initially come out greyish-black or soapy. This is normal.
figu re 2
9:00
12:00
figu re 1
figu re 3
RESET
11
MAINTENANCE
Hold the faucet attachment with one hand and the
faucet with the other hand, then pull down faucet
attachment until it comes o.
If necessary, use the small wrench to unscrew the
faucet adapter.
Clean the faucet adapter to remove any hard water
deposits or impurities that may clog the purifier.
CLEANING THE FAUCET ADAPTER
Periodically clean the faucet adapter to remove any hard water deposits or impurities that
might clog the purifier.
TROUBLESHOOTING
LED INDICATORS
ICON LED STATUS CAUSE SOLUTION
Solid Orange LED
The purifier is in an abnormal
state.
Contact your local Nu Skin Distributor
Center.
Flashing
Orange LED
3in1 cartridge is nearing the end
of its life cycle.
Purchase a new 3in1 cartridge soon.
Solid Orange LED
3in1 cartridge’s life cycle has
expired.
Replace the 3in1 cartridge.
Solid Blue LED 3in1 cartridge is working properly.
Flashing
Orange LED
Water might be over 38˚C. Lower the temperature of the water.
Solid Orange LED
Purifier is powering on.
Purifier has not been used for
72 hours.
Touch the “Purified Water” button and
run water until the LED light changes
to blue.
3in1 cartridge’s life cycle has
expired.
Replace the 3in1 cartridge.
Solid Blue LED Purifier is working properly.
12
TROUBLESHOOTING (cont.)
MALFUNCTION CHECK LIST/CAUSE
No purified water comes
from the faucet
Make sure the power cord is plugged into an electrical outlet.
Check if the abnormal state LED indicator is on.
Make sure the 3in1 cartridge is installed correctly.
Make sure the main water supply is open.
Make sure you are using the correct 3in1 cartridge.
Top blue LED ring is
blinking
Make sure the main water valve is open.
Poor purified water flow Check the 3in1 cartridge is not blocked.
Check the life cycle of the current 3in1 cartridge.
Tap water pressure is too low.
Inappropriate water temperature.
Increase water temperature, but do not exceed 38˚
C.
Clean the faucet adapter to remove any deposits or impurities.
Purified Water mode
switches to Tap Water
mode
Make sure the water temperature of the purified water does
not exceed 38˚
C.
If the water purifier overheats because of excessive use, wait
until it cools down.
Make sure the 3in1 cartridge has been installed correctly.
PRECAUTIONS
STORAGE
• Do not use, store, or expose the EcoSphere Water Purifier to environments where temperatures drop below 0˚C.
WATER SOURCE/PRESSURE
• Use the EcoSphere Water Purifier only with a municipal water source.
• Do not use if the water pressure is higher than 0.10.4MPa, or install a water pressure
reducing valve.
DAILY MAINTENANCE
• If the EcoSphere Water Purifier fails to work properly, contact your local Nu Skin Distributor
Center for support.
• Do not attempt to repair the EcoSphere Water Purifier yourself. This will void any warranty.
• When moving or transporting the EcoSphere Water Purifier, make sure you package all the
components securely.
• Regularly clean the faucet adapter and other component of the EcoSphere Water
Purifier to avoid damage.
• When cleaning the exterior of the EcoSphere Water Purifier, make sure water does not drip
into the hole that contains the 3in1 cartridge.
• Do not clean the interior of the 3in1 cartridge chamber with tap water, as doing so may cause
bad odors and bacteria to build up inside the chamber.
• Replace the 3in1 cartridge when the LED light is orange.
13
USE
• If you are not going to use your EcoSphere Water Purifier for a long time, turn o the faucet,
and switch o the power supply.
• When using the EcoSphere Water Purifier after a long period of unuse, run the faucet to
flush any particles that might clog the 3in1 cartridge before attaching the water purifier.
• When using water that is poor quality, low temperature, or very low pressure, the flow of
purified water will be weak. This is normal.
• When using a new 3in1 cartridge, purified water will start by coming out greyish-black or
soapy. This is normal. Please continue to let water run through the purifier until water comes
out clear.
• Do not place the EcoSphere Water Purifier on its side or upside down.
• Do not use the EcoSphere Water Purifier at temperatures below 5˚C or higher than 38˚C as
this may cause damage to the unit.
• Do not drop the Ecosphere Water Purifier and 3in1 Cartridge.
• Discard all shipping packaging. Do not let children play with the EcoSphere Water Purifier.
Young children should be supervised when operating the purifier.
• Do not use in public areas.
ACCESSORIES AND CARTRIDGES
Always use the accessories and 3in1 cartridge appropriate for the EcoSphere Water Purifier.
STORAGE
• Direct sunlight shortens the life cycle of the EcoSphere Water Purifier components.
• Do not use in temperatures below 5˚C or higher than 38˚C as this may cause damage to
the purifier.
• Do not place near fire or magnetic devices.
• Do not place near humid or dusty areas.
• Do not place heavy objects on top of the unit.
ADDITIONAL CONSIDERATIONS
• Do not use the power cord if it is wet.
• Do not bend, twist, or damage the power cord in any way.
• If the power cord gets damaged in any way, stop using the device and contact your local
Nu Skin Distributor Center for support.
• Do not pull on the power cord to unplug it from the wall outlet.
• This device can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the device in a safe way and understand the
hazards involved. Children shall not play with the device. Cleaning and user maintenance shall
not be made by children without supervision.
• Children should be supervised to ensure that they do not play with the device.
• This device contains a UVC emitter.
• The UVC emitter cannot be replaced by users.
• Unintended use of the device or damage to the housing may result in the escape of dangerous
UVC radiation. UVC radiation may, even in little doses, cause harm to the eyes and skin.
• Devices that are obviously damaged must not be operated.
14
MAIN SPECIFICATIONS
NAME
EcoSphere Water Purifier
MODEL
PRODUCT SIZE
W X H X D mm
WEIGHT
. kg—water purifier
. kg—3in1 cartridge
WATER SOURCE
Municipal tap water
CAPACITY
L
WATER FLOW*
1.7L/min
OPERATING WATER PRESSURE
..MPa
OPERATI NG WATER TEMPE R ATUR E
˚C
INPUT
V Hz
POWER
W
IEC PROTECTION CLASS
Class II
* Water flow was measured under laboratory test conditions.
Test conditions: Tap water; water pressure . MPa; water temperature ˚C, after two minutes of
continuous operation.
REPLACEMENT AND WARRANTY INFORMATION
lim ited o ne-year warranty: Nu Skin guarantees your EcoSphere Water Purifier to be free
from defects in materials and workmanship for a period of one year from the original date of
consumer purchase. This warranty does not cover damage to the product as a result of misuse
or accident. If the product becomes defective within the one-year warranty period, please call
your local Nu Skin Distributor Center for support. Please retain your proof of purchase (i.e.
original invoice) to claim your replacement and warranty.
© NSE PRODUCTS, INC.
WEST CENTER STREET, PROVO, UT NUSKIN .COM
Scan QR code to download
User Manual in other languages.
Loading...