including but not limited to graphic, electronic, and mechanical (which includes photocopy and
recording) systems without the permission of NuRAN.
To guarantee the accuracy of the information contained in this document, a very detailed review
of its contents was performed during its preparation. The information corresponds to the version
of the product manufactured before the date indicated on the cover. Differences can exist
between this document and the product if the product was modified after the release of this
document.
NuRAN reserves the right to modify, improve, or change the products describe in this document
without notice.
Revision History
CONFIDENTIAL2 of 40
GSM LiteCell Installation GuideVersion 0.95
0.95
April 25, 2017
Added a note about atenna separation to persons to meet RF
Table 11Deployment Kit Power Supply Specifications ............................................................ 23
Table 12Deployment Kit Power Supply Specifications ............................................................ 24
CONFIDENTIAL6 of 40
GSM LiteCell Installation GuideVersion 0.95
1 Introduction
This document explains how to install the GSM LiteCell, an easy-to-deploy and low-power
consumption cellular base station.
1.1 Scope
This document covers installation requirements, site preparation, and physical equipment
installation. After completing these procedures, the base station equipment will be powered on
and ready for configuration.
1.2 Intended Audience
This document is intended for installation technicians. The reader should have a basic
understanding of electricity, telecommunications equipment, and RF technology.
1.3 Related Documents
The following documents are included in the GSM LiteCell documentation suite:
NOTE: Notes contain information that may be of particular usefulness or direct the
reader's attention to issues that may cause difficulties if ignored.
CAUTION: A general caution is shown when there is risk of personal injury or
equipment damage from non-electrical hazards.
WARNING: An electrical warning is shown when there is risk of personal injury or
equipment damage from electrical hazards.
1.4 Notices and Safety Warnings
Critical reader information is indicated throughout this document using specially formatted text
and/or icons.
1.5 Safety Precautions
Always observe the following recommendations to ensure maximum safety:
The equipment is intended for installation in a restricted access location.
Do not install or operate the equipment without proper training.
Do not operate the equipment without the specified antennas correctly installed.
Observe all local or national RF regulations with respect to operating RF equipment.
Do not stand in front of, or in close proximity to, the antennas when they are powered on.
Do not modify the equipment, integrate with non-approved devices, or operate in a non-
approved manner.
Always follow applicable electrical codes when installing the equipment.
Disconnect power from the equipment when it is not in use for an extended period of time.
CAUTION: Remove all protective foils and packaging material prior to usage.
CONFIDENTIAL8 of 40
GSM LiteCell Installation GuideVersion 0.95
WARNING: Outdoor towers are susceptible to damage caused by direct or nearby
lightning strikes. To reduce the risk of serious injury and equipment damage
caused by lightning strikes, the tower should be equipped with a lightning
protection system that is designed and installed by a qualified professional
installer and meets all applicable electrical codes.
1.6 Tower Lightning Protection
A lightning rod should be installed on the tower above the
GSM antennas. The height must be at least twice the
distance that the antennas are mounted away from the
tower. In areas with a high frequency of lightning strikes, the
height should be increased up to 5 times this distance.
The lightning rod must be attached to a conductor cable or
grounding bus, which in turn is connected to a ground rod at
least 2.44 m (8 ft) long, 16 mm (6/8 in) in diameter, and
extends into the ground at least 0.92 m (3 ft) below any
adjacent structure.
Figure 1. Tower Lightning Protection
CONFIDENTIAL9 of 40
GSM LiteCell Installation GuideVersion 0.95
1.7 Waterproofing Connectors
All outdoor coaxial and power connectors must be waterproofed using waterproof and UVresistant tape.
Figure 2. Waterproofing Connectors
To cover a connector:
1. Cut a suitable length of the waterproof tape from the roll.
2. Remove the backing.
3. Starting from 2.5 cm (1 in) before the connector, wrap the entire length while stretching
the tape material. When stretched, the tape will stick to itself and form a waterproof
seal around the connector.
4. Keep wrapping until you are 2–3 cm (0.75–1.25 in) past the connector.
5. Cover the waterproof tape with a piece of UV protection tape.
1.8 Drip Loops
Whenever a cable is connected to a device, is secured to the side of a
structure, or enters a building or enclosure, form a loop with the cable so
that water follows the cable and drips away from the device, structure, or
building.
Figure 3. Drip Loop
CONFIDENTIAL10 of 40
GSM LiteCell Installation GuideVersion 0.95
1.9 Litecell Contents
The GSM LiteCell box includes the following items:
GSM Litecell
Flange nuts and screws
U-bolts and clamps
Waterproof RF cap
Power cable plug
Ethernet cable plug
1.10 Deployment Kit Contents
The GSM LiteCell deployment kit, if ordered, includes the following items:
GPS antenna with cable and SMA connector.
GPS antenna mounting hardware
2 GSM omni-direction antennas
RF cable with N-Type connectors, 4.75 m (15 ft)
15 mounting clamps (used for both GSM LiteCell and standoff pipes)
2 standoff pipes
Flange nuts and screws
Power supply fixation clamps
Waterproofing tape
UV protection tape
UV-rated tie wraps (x50)
Outdoor Ethernet cable, 50 m (164 ft) and RJ-45 connectors
Optional AC power supply or DC power cord, 50 m (164 ft)
Tool kit (screw drivers, adjustable wrench)
CONFIDENTIAL11 of 40
GSM LiteCell Installation GuideVersion 0.95
CAUTION: The GSM LiteCell contains no user-serviceable parts. Do not open or
modify any part of the product, as this action will automatically void the product’s
warranty. All repairs must be performed by qualified service personnel. Do not use
the GSM LiteCell with any non-approved third-party products.
AC
Alternating Current
Mbps
Megabits per second
ARFCN
Absolute Radio-Frequency
Channel Number
PPM
Parts Per Million
BER
Bit error rate
PSU
Power Supply Unit
DC
Direct current
RAN
Radio Access Network
EDGE
Enhanced Data rates for GSM
Evolution
RF
Radio Frequency
GSM
Global System for Mobile
Communications (GSM)
SMA
Sub Miniature version A
GPP
3rd Generation Partnership
Project
IP
Internet Protocol
GPS
Global Positioning System
IP##
Ingress Protection
LED
Light-Emitting Diode
UV
Ultraviolet light
1.11 Product Warranty
For warranty information about this product, refer to your NuRan Limited Product Warranty
and any applicable service agreements.
When contacting NuRan, obtain the serial number and MAC address of your GSM LiteCell. This
information is printed on the product label and will assist in troubleshooting and resolving your
issues.
1.12 Acronyms and Abbreviations
CONFIDENTIAL12 of 40
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.