Numatic HT4045, TT4045G, TT4055G Owner's Manual
Warning! Read instructions before using the machine
Owner Instructions
HT4045
TT4045G
TT4055G
SCRUBBER DRYER
www.numatic.co.uk
SCRUBBER DRYER
Index
HT 4045, TT 4045, TT 4055
Machine Overview ................................ Pages 2-3
Machine Set up Guide ................................ Page 4-7
Tilting the Handle ................................ Page 4
Fitting the Top Tank ................................ Page 4
Fitting the Brush ................................ Page 4
Tipping the Brush Deck ................................ Page 5
Fitting the Floor-tool .............................. Page 5
Fitting the hose guide ................................ Page 6
Fill the Clean-water tank ................................ Page 6
Clean Water Level ................................ Page 7
Control of Cleaning substances (COSHH) ...... Page 7
Clean Water Tap On / O ................................ Page 7
Pre Cleaning ................................ Page 7
Pre Scrubbing ................................ Page 8
Lowering the oor-tool ................................ Page 8
Breakaway oor-tool feature ........................... Page 8
Setting the cleaning controls ....................... Page 9
Regular Maintenance ................................ Page 10
Tanks and Filters ................................ Page 10
Changing the Floor-tool Blades ................... Page 11
O-Aisle Cleaning Kit ................................ Page 12
Specications ................................ Page 12
HT 4045 Face Fitting ................................ Page 13-14
Trouble Shooting ................................ Page 15
Recommended Spare Parts .......................... Page 15
Schematic Diagram ................................ Page 16
Rating Label / Personal Protective Equipment /
Recycling ................................ Page 17
Safety Precautions ................................ Page 18
EU Declaration Document ............................. Page 19
Warranty ................................ Page 19
Company Address ................................ Page 20
1
Operator Control Panel
2
Separator
3
Top Tank (waste-water)
4
Waste-water Emptying Hose
5
Bottom Tank (clean-water)
6
Deck Locking Pin
7
Brush Deck
8
Handle Position Lever
9
Vacuum Switch
10
Pump Switch
11
Power Light
12
On / Off Switch
13
Triggers
14
Clean-water Tank Fill Point / Filler Hose
15
Floor-tool Vacuum Hose
16
Vacuum Hose
17
Clean-water Tank Emptying Hose & Fill Level
18
Floor-tool Lifting Lever
19
Floor-tool Retaining Knobs
20
Semi Parabolic Floor-tool
21
Clean Water Filter
22
Brush
PLEASE READ
BEFORE COMMENCING
OPERATION
After the removal of all the
packaging, carefully open
and check the contents
●
Owner Manual
● Scrub Brush
●
Semi Parabolic Floor-tool
●
Floor-tool Hose
Machine Overview
1
3
4
5
6
7
8
10
13
14 14
15
16
17
18
19
20
21
11
2
22
9
12
13
19
8
Machine Set Up
4
www.numatic.co.uk
Tilting the handle
Using the handle position lever (Fig.1).
Fit the top tank to the machine (Fig.3).
Fitting top tank
1
2
3
4
PLEASE READ BEFORE COMMENCING ANY OPERATION AFTER THE REMOVAL OF ALL
THE PACKAGING, CAREFULLY OPEN AND CHECK THE CONTENTS.
!!
Move the handle into the upright position (Fig.2).
Fit both vacuum and oor-tool hose to the separator (Fig.4).
Vacuum hose
Floor-tool hose
Fitting the brush - Safety gloves are recommended for the changing of used brushes.
Featuring the Nulock brush system. The brush is simply pushed and twisted to lock, making tting and removal a simple
process. The Pad is retained using Numatic’s own PadLoc system (ask your supplier for details).
Only use manufacturer supplied brushes / pads. TT 4045G requires a 450mm brush or a 400mm pad. TT 4055G requires a 550mm
brush or a 500mm pad. Fit the brush / pad to the drive chuck, twist to lock the brush (Fig.5) / pad in place (Fig.6).
5
6
Machine Set Up
5
T 01460 68600
Tipping the Brush Deck
Fitting the Floor-tool
The oor-tool has been designed for quick tting, allowing easy squeegee blade replacement and a safety knock-o feature if the oortool gets snagged, whilst in transit.
Note: It is easier to t the oor-tool if the weight of the machine is resting on the brush. Ensure the brush is tted rst.
Raise the oor-tool for transit or lower for cleaning operation using the lifting handle tted to the back of the machine
(Fig.11).
For tting the oor-tool blades (See Page 13).
11
To tip the deck into the down position (Operating mode). Press
in the brush deck locking pin (Fig.7) and rotate the brush deck
(Fig.8).
7
8
To change to brush deck up position, (Transit mode) simply
lift the deck and the sprung loaded locking pin will activate to
hold the deck up.
!!
ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF
BEFORE MAKING ANY ADJUSTMENTS
Fit the oor-tool and retain using the detent pin (Fig.9).
9
10
The lifting strap is held by a detent pin (Fig.10).
Machine Set Up
6
www.numatic.co.uk
The TT Range are all equipped with a 40 litre clean-water tank allowing large areas to be cleaning in a single ll.
Filling the clean-water tank
Ret vacuum hose to the Floor-tool when nished.
The vacuum hose has a U-bend clip which creates a U-bend in the hose preventing water spillage when the vacuum is switched o. If
you need to remove the U-bend clip for any reason always ensure it is retted correctly before you resume operation (Fig 36-39).
30mm
MAX
Fitting the Hose Guide
Note:
DO NOT push the vacuum hose onto the Floor-tool with the Floor-tool in the raised position.
Raise oor-tool again before driving to the cleaning area.
!!
Note:
Great care must be taken to ensure that contaminants (leaves,hair, dirt, etc) are not
allowed to enter the clean-water tank during the lling process. If using a bucket or
similar, ensure it is always clean and free from debris.
!!
12
13
The large cap on the left can be
removed for lling from a bucket or
suitable container (Fig.13).
To ll the clean-water tank, use the
FLEXI - FILL pipe from either a tap or
hose pipe (Fig.12).
Fill the clean-water tank
to a maximum of 40 litres,
including cleaning chemicals
if required. Follow chemical
manufactures guide lines.
Loading...