Numark Industries CDMIX-1 User Manual

Professional Disc Jockey Products
®
CD MIX-1
PROFESSIONAL CD MIXING CONSOLE
OPERATING MANUAL
©1999 Industries http://www.numark.com
CD MIX-1
Safety Information and Product Registration
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE ANY COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL ONLY.
The lightning flash with arrowhead symbol within the
equilateral triangle is intended to alert the user to the
presence of un-insulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying this appliance.
CAUTION
FOR USA & CANADIAN MODELS ONLY
TO PREVENT ELECTRIC SHOCK DO NOT USE
THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET
UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE EXPOSURE.
SAFETY INSTRUCTIONS
(1) Read Instructions - All the safety and operating
instructions should be read before this product is connected and used.
(2) Retain Instructions - The safety and operating
instructions should be kept for future reference.
(3) Heed Warnings - All warnings on this product and in
these operating instructions should be followed.
(4) Follow Instructions - All operating and other
instructions should be followed.
(5) Water and Moisture - This product should be kept
away from direct contact with liquids.
(6) Heat - Avoid placing this product to close to any high
heat sources such as radiators.
(7) Ventilation - The appliance should be situated so
that it’s location or position does not interfere with it’s proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation opening; or, placed in a built­installation, such as bookcase or cabinet that may impede the flow of air through the ventilation openings.
(8) Power Sources - This product should be connected
to a power supply only of the type described in these operating instructions, or as marked on the unit.
(9) Power Cord Protection - Power supply cords should
be routed so that they are not likely to be walked upon or pinched by items placed on or against them. When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord.
(10) Object and Liquid Entry - Take care that objects do
not fall into and that liquids are not spilled into the inside of the mixer.
(11) Cleaning – The appliance should be cleaned only as
recommended by the manufacturer.
(12) Non-use Periods – The power cord of the appliance
should be unplugged from the outlet when left unused for long periods of time.
(13) Damage Requiring Service - Only qualified
personnel should service this product. If you have any questions about service please contact Numark at the number(s) shown on the back cover of this manual.
(14) Grounding or Polarization - Precautions should be
taken so that the grounding or polarization means built into the CD player is not defeated.
(15) Internal/External Voltage Selectors - Internal or
external voltage selector switches, if any, should only be reset and re-equipped with a proper plug for alternative voltage by a qualified service technician. Do not attempt to alter this yourself.
©1999 Numark Industries - 2 - http://www.numark.com
WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture. Electrical equipment should NEVER be kept or stored in damp environments.
DANGER: INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED. AVOID DIRECT EXPOSURE TO BEAM.
CAUTION: This product utilizes a laser. Use of controls or adjustments other than those specified herein may result in hazardous radiation exposure.
SERVICE INSTRUCTIONS
1. Disconnect power cord before servicing
2. Replace critical components only with factory parts or recommended equivalents
3. For AC line powered units - Before
returning repaired unit to user, use an ohmmeter to measure from both AC plug blades to all exposed metallic parts. The resistance should be no more than 100,000ohms.
CD MIX-1
NOTICE CONCERNING FCC REGULATIONS
This equipment generates and uses radio frequency energy and may cause interference to radio and television reception if you do not operate it in strict accordance with the procedures detailed in this OPERATING MANUAL. This unit complies with Class B computing device rules in accordance with the specifications in Sub-part J or Part 15 of the FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. There is no guarantee, however, that interference will not occur in a particular installation. If the unit does cause interference to any radio or television reception, try to reduce it by one or more of the following means:
a) Reposition the other unit and/or its antennae b) Move this unit c) Move this unit and the other unit(s) further apart d) Plug this unit into a different AC outlet so that it is on a different circuit from the other equipment.
This note is in accordance with Section 15.838 of the FCC Rules.
This unit does not exceed the Class B limits for radio noise emission from digital apparatus set out in the radio interference regulations of the Canadian Department of Communications.
DOUBLE INSULATED - When servicing use only identical replacement parts
For 220-volt use in USA, use NEMA style 220-volt plug. For other countries use proper plug for local outlet.
Please record the serial number of your unit as shown on the back of the chassis as well as the name of the dealer from whom you purchased the unit. Retain this information and your original purchase receipt for your records. Please return the enclosed warranty card to register your CD player with us.
MODEL: __________________________ PURCHASED FROM:_________________________ SERIAL NUMBER:___________________ DATE OF PURCHASE:________________________
- The Leader in DJ Technology
©1999 Numark Industries - 3 - http://www.numark.com
CD MIX-1
®
CD MIX-1
PROFESSIONAL CD MIXING CONSOLE
CONGRATULATIONS...
You have just purchased a combination dual CD player and mixer designed specifically for the professional DJ. This unit has been designed to provide portable CD mixing with the same ease and creativity that you have enjoyed with records. Please take a few moments to familiarize yourself with the CD MIX-1 by reading the following information before attempting to operate the unit.
Once again, congratulations and thank you for choosing the CD MIX-1.
FEATURES:
CD Section
2 independent CD units
Mechanical Anti-Shock
Ability to play 3" and 5" CDs
Plays CD and CDR (recordable CDs)
Pitch/Jog Wheel for both setting cue points
and adjusting tempo
3 search speeds
Large back lit LCD Display
Track sequence programming
Time button with elapse and remain time
bar
Single/Continuous modes
Pitch percentage display
+/- 12% pitch adjustment
Auto dead space elimination
Ability to autostart player with use of the
crossfader
BPM COUNTER
Mixer Section
External input for 2 Phono or 2 Line inputs
Master balanced/unbalanced and record
output
Direct input for onboard CD units
Input for External Microphone with
independent gain control
Crossfader to blend between 2 Channels and control Auto start of the CD units
Three band Equalizer for master output
Dual Band, 12-segment LED output display
Fader CD Start button
Headphone output for 1/4" and 1/8" style
plugs with the ability to cue any channel
12VDC power input to allow car battery usage
©1999 Numark Industries - 4 - http://www.numark.com
TABLE OF CONTENTS
Safety and Registration 2 Introduction 4 Set-up Instructions & Connections 7 Important Information 6
Description of the Features
CD Player 7 Display 8 Mixer 9 Rear Panel 10
CD MIX-1
Basic Operation
Play, Pause and Cue Operations 11 Matching the Tempo 12 Beat Matching Using Pitch Bend 12
Example of Mixing 13 Before Switching off the Power 14 Troubleshooting Guide 14 Information and Specifications 15 Warranty 16
- The Leader in DJ Technology
©1999 Numark Industries - 5 - http://www.numark.com
CD MIX-1
IMPORTANT INFORMATION...
CHECK TO BE SURE THE FOLLOWING ITEMS ARE IN THIS BOX:
(1) CD MIX-1 (1) OWNERS MANUAL (THIS BOOKLET) (1) POWER ADAPTER
Please read this entire manual before connecting this unit to your system.
For optimum performance: a) Never use spray cleaners on the slide controls. Residues cause excessive dirt build-up and this
will void your warranty. In normal use slide controls can last for many years. If they malfunction
(usually because of a dirty or dusty environment) consult a professional technician. b) Always make sure that AC power is OFF while making any connections. c) Use appropriate cables throughout your system. Do not use excessively long cables (i.e. over
50ft/14m) Be sure plugs and jacks are tightly mated. Loose connections can cause hum, noise or
intermittents that could easily damage your speakers. Make the input and output connections with
readily available low-capacitance stereo cables. Quality cable makes a big difference in audio
fidelity and punch. See your Numark dealer or an electronics or audio specialist store if you are
not sure which cables to get. d) Never attempt to make any adjustments or repairs other than those described in this manual.
Take the unit to your dealer or to an authorized Numark Service Center. e) ALWAYS remember: “TURN AMPS ON LAST AND OFF FIRST”. Begin with master faders or
volume controls on minimum and the amplifier gain/input control(s) down. Wait 8 to 10 seconds
before turning up the volume. This prevents transients which may cause severe speaker damage. f) Use restraint when operating controls. Try to move them slowly. Rapid adjustments could damage
speakers due to amplifier clipping. g) Avoid amplifier “clipping” at all costs: this occurs when the red LEDs (usually on the front panel of
most professional power amplifiers) start flashing. “Clipping” is when the power amplifier is
distorting and working beyond it’s limits. Amplifier distortion is THE major cause of speaker failure. h) To prevent fire or shock hazard, do not expose the unit to rain or moisture. Never place cans of
beer, soda, glasses of water or anything wet on top of the unit!
©1999 Numark Industries - 6 - http://www.numark.com
DESCRIPTION CD MIX-1 CD PLAYER FEATURES
LED is lit, then moving the sliding fader. The pitch will not be changed if the PITCH LED is off.
10. SEARCH WHEEL (OUTER RING) - 3 forward and 3 reverse speed positions for searching through songs. The more you turn the wheel in either direction the faster you search through the music.
11. PITCH BEND/JOG WHEEL (INNER RING) - The jog wheel serves 2 functions depending on the current mode.
a) The jog wheel will control a slow frame search
when the CD is not playing. To set a new frame cue point, spin the wheel then press play when you have determined the proper position. Press CUE to return to the “CUE POINT”.
1. OPEN/CLOSE (Disc Tray Open/Close) - Press to load or eject the disc. Each press will open or close the disc tray on the transport. NOTE: Tray will not
open unless the disc has been paused. Tray will automatically close after 30 seconds.
2. TIME (Time Button) - Switches the time display between elapsed playing time and remaining time on the track and remaining time on the entire CD.
3. CONT/SING - Will cause just a single track to play or all tracks in order by pressing once or twice.
4. LCD DISPLAY - Indicates all the functions, as they are occurring, with the CD. These functions are explained in the next section.
5. TRACK (Track Buttons) - Used to select the track to be played.
6. Track 10 Button - This button is for quickly advancing to higher tracks on a CD.
7. PROGRAM - Depress this button and the unit will stop and the program indicator will light. Select each track to be programmed and press the PROGRAM button between selections. You can program up to 30 tracks. Press PLAY to start the program. To exit and erase program, either hold the program button down for more than 2 seconds while the unit is stopped, open the disc tray, or turn off the power.
8. PITCH (Pitch Button) - Activates the Pitch Slider.
9. PITCH SLIDER - The pitch can be changed up to +/-12% by pressing the PITCH button so the PITCH
b) When both CD players are playing a CD, the pitch
bend function allows the positioning of the bass beats to be matched after the pitch of each disc is matched. Either player can “catch up” or “fall back” to match the other player. The jog wheel will temporarily bend the pitch of the music if the song is already playing by rotating the wheel clockwise to speed up or counterclockwise to slow down. By changing the pitch of one disc with respect to the pitch of the other disc, the beats can be matched.
12. CUE - Pressing the CUE button during play provides a return to the position at which play was started. If PAUSE is used before CUE, that will become the cue point. Alternately pressing the PLAY button and the CUE button allows the CD to be played from the same position any number of times. The CUE LED will light up from the time the CUE button is pressed until the CD has been reset to the position at which play was started. Steady lighting of this LED indicates the ready condition.
13. START/PAUSE (Play/Pause Button) - Each press of the Play/Pause Button causes the operation to change from play to pause or from pause to play.
14. BPM/PITCH BUTTON - Switches the mode of the display between showing the BPM and the percentage change in pitch.
15. TAP BUTTON - Tap this button with the beat of the music to determine the current Beats Per Minute (BPM).
CD MIX-1
- The Leader in DJ Technology
©1999 Numark Industries - 7 - http://www.numark.com
CD MIX-1
LCD DISPLAY FEATURES
1. PLAY - Active while the unit is actually playing a CD.
2. PAUSE - Active when the unit is paused.
3. CUE - Flashing when the unit is setting a cue point. Lit continuously when the unit is paused at a cue point.
4. PROGRAM - Used for pre-programming the track order to automatically be played by the unit. This is a great function if you need to leave the CD player alone.
5. TIME MODE - (Elapsed) is for showing time as it is taking place. (Remain) shows how much time is left on a particular track. This function is controlled by the TIME
BUTTON.
6. SINGLE - Shows when the unit is set to play just one track at a time. When this is not lit, the CD will play continuously through all tracks. This function is controlled by the SING/CONT BUTTON.
7. PITCH - Is lit when the PITCH BUTTON is active.
8. TIME BAR - Shows either time remaining or elapsed depending on the setting of the TIME BUTTON.
9. PITCH/BPM - Shows the percentage change in pitch or current BPM.
10. TRACK - Shows the current track that the unit is playing.
11. MINUTES - Shows the minutes elapsed or remaining depending on mode setting.
12. SECONDS - Shows the seconds elapsed or remaining depending on mode setting.
13. FRAMES - The CD Player breaks down a second into 75 frames for accurate cueing. This shows the frames elapsed or remaining depending on mode setting.
©1999 Numark Industries - 8 - http://www.numark.com
CD MIX-1
MIXER FEATURES
1. Input fader - Controls individual source levels in the mix
2. Input toggle switch - Selects which source will be live to that channel based on what you have connected to the rear panel input section
3. Replaceable Crossfader - Achieves clean segues between the two input channels. "Hard left" selects Channel 1. "Hard right" selects Channel 2. With the crossfader centered, both assigned channels are live. Use the crossfader for fast and seamless segues from one selected channel to the other
Note: The crossfader is user replaceable in case of failure. Simply unscrew the two large screws which hold it in place, lift it out and disconnect it’s cable. Re-attach the new crossfader and screw the mounting plate back onto the unit - you’re back in business!
4. Fader Start – Activation allows you to start the CD players from you crossfader. Travel from left to right will start the right CD player and pause the left CD player
5. Mic Input Fader – Adjusts microphone level
6. Mic On/Off Toggle – Activates microphone
7. Master Fader - Controls the overall output level
8. Stereo/Mono toggle - Changes the Master output between Mono and Stereo
9. Stereo EQ – Adjust final master output equalization of treble, middle, and bass
10. LED METER - Indicates the Master output level
11. Channel Cue Selector - Used to route channel audio to your headphones
12. Headphone Level – Adjusts cue volume
13. Headphone Jacks – Used to connect either 1/8” or 1/4” plugs for audio monitoring with headphones
- The Leader in DJ Technology
©1999 Numark Industries - 9 - http://www.numark.com
CD MIX-1
REAR PANEL FEATURES
1. Channels Inputs - Unbalanced RCA jacks for connecting external sources. The Phono/Line Input is selected with the toggle switch on the front panel. You can connect stereo audio from Turntables, HiFi VCRs, cassette and reel-to-reel tape decks, DAT machines, CD players, laser discs, tuners, even synthesizers or other mixing consoles. NOTE: Plug mono audio sources into both Left and Right inputs using a "Y" cable connector.
2. GND - Grounding lug for turntable connection. Always use this connection when using turntables. (your turntable cable should have a grounding wire)
3. Line/Phono Input switch - Use this to allow either line level or phono level equipment to be plugged into your channel inputs. When Phono input is selected, your signal is fed directly to the high-quality RIAA phono pre-amplifiers. Use this position only for turntables. Line level sources will overload the sensitive phono pre-amps and will sound very bad, so always be sure to toggle the line/phono switch over to line before connection of line sources.
4. Record Outputs - Unbalanced RCA jacks used to send the output of the program any connected recording device.
5. Stereo Main Outputs - Unbalanced RCA connectors controlled by the Master fader.
6. Balanced Main Outputs - Low-impedance XLR type connectors controlled by the Master fader.
7. Mic Input – Plug your 1/4” Microphone plug in here.
8. Power Connector - Plug in power adapter here and check the voltage level to match your country’s standard.
9. Power Switch – Turn on unit here.
©1999 Numark Industries - 10 - http://www.numark.com
CD MIX-1
DESCRIPTION OF THE PLAY/PAUSE AND CUE OPERATIONS
PLAY and CUE
Pressing the “PLAY/PAUSE” button starts the disc. Pressing the “CUE” button will reset the disc to the last place where the disc was started. This is called the cue point. By alternately pressing the “PLAY/PAUSE” button and the “CUE” button, the disc may be returned and played from the cue point any number of times. This function is called back cue.
PLAY, PAUSE and CUE
EDITING CUE POINT
When the inner search dial is turned while a cue point is set, a new cue point can be located. The CD player will repeatedly play small parts of the CD as you move it to the desired position. By pressing “PLAY/PAUSE” then “CUE” you can confirm that this new cue point is desirable
- The Leader in DJ Technology
©1999 Numark Industries - 11 - http://www.numark.com
CD MIX-1
MATCHING THE BEATS PER MINUTE (BPM)
Match the tempo by monitoring the music of both PLAYER 1 and PLAYER 2 by ear and adjusting the pitch. When the tempo of the music of the selected CD player is slow compared to the tempo of the other player, move the slider to the ( + ) side and match the tempo. When faster, move the pitch slider to the ( - ) side. The following illustration shows the case of matching the pitch of PLAYER 2 to the pitch of the music being played on PLAYER 1.
Press PLAY/PAUSE to start PLAYER 1
PLAYER 1 is playing
Listen to PLAYER 2 in your headphones
When PLAYER 2 is slow
compared to PLAYER 1
speed up PLAYER 2
USING THE BPM DISPLAY FEATURE
Press the BPM button to select the BPM feature on the display
on the side of the CD player that you wish to set. Tap the
Counter button to the beat of the music.
Press PLAY/PAUSE to start PLAYER 2
Both CD players are playing discs.
When PLAYER 2 is fast compared to PLAYER 1
slow down PLAYER 2
You will see the BPM number appear in the display. The more
times you tap the more accurate your number will be. When
you adjust the pitch slider the display number will change by an
equal percentage.
BEAT MATCHING USING PITCH BEND
If you find the BPM’s (Beats Per Minute or Tempos) are the same, however, the drum beats are not matched you will need to temporarily change the pitch. The illustration below shows how to match the beat of PLAYER 2 to the beat of the music being played on PLAYER 1. (This procedure can be done on either PLAYER).
After matching the BPM’s adjust the pitch temporarily as follows:
When PLAYER 2 is rotate the jog wheel counter clockwise
The pitch changes automatically while the jog wheel is rotated. The faster you rotate the wheel the more you change. Releasing the wheel results in a return to the original pitch. (So the BPM’s are once again the same.)
©1999 Numark Industries - 12 - http://www.numark.com
When PLAYER 2 is behind rotate the jog wheel clockwise
CD MIX-1
EXAMPLE OF MIXING USING BOTH PLAYERS OF YOUR CD PLAYER
While playing a disc on PLAYER 1, load a disc into PLAYER 2 and select your next track, match its pitch to the track playing on PLAYER1 and when you are ready use the crossfader on your mixer to fade from PLAYER 1 to PLAYER 2.
Load a disc in PLAYER 1
and select the track and
press PLAY.
Load a disc in PLAYER 2
and select the track then
play.
Set and edit a start cue
point on PLAYER 2
PLAYER 1
Load a disc and press the
OPEN/CLOSE button.
PLAYER 2
Load a disc and press the
OPEN/CLOSE button.
PLAYER 2
Press the Pause button of
PLAYER 2.
PLAYER 1
Select the track to be
played.
PLAYER 2
Select the track to be
played.
PLAYER 2
Rapidly search for a cue
point using the outer wheel
PLAYER 1
Press the PLAY button
PLAYER 2
Press the PLAY button
PLAYER 2
Slowly set the right cue
point using the inner wheel
Check you new cue point
Do a MIX!
PLAYER 2
Listen with the monitor and
press the play button.
PLAYER 2
With a matching downbeat
from Player 1 press the
play button.
If you are beat mixing, turn
PLAYER 2
Press the cue button then
play to be sure of the set
cue point.
PLAYER 2
on your Pitch adjust and
follow the directions for
beat matching.
PLAYER 2
Reset the player to the
Cue point by pressing Cue
MIXER
When you are happy with
your mix the crossfader
accordingly.
- The Leader in DJ Technology
©1999 Numark Industries - 13 - http://www.numark.com
CD MIX-1
BEFORE SWITCHING OFF THE POWER:
When you have finished using the CD player, be sure that the disc tray is closed with the “OPEN/CLOSE” button before switching off the power.
DO NOT switch off the power when
the disc holder is open.
TROUBLESHOOTING:
Symptom Possible Cause Corrective Action
The power fails to switch on when the POWER switch is set to on
Disc play does not start The disc is loaded upside down
No sound Improper output cable
Sound skips The CD player is still subject to
Programmed disc play will not function
Poor power plug connection at the AC outlet or IEC Power cord loose from rear of unit
The disc is too dirty
connections Improper amplifier operation
vibrations or physical shock The disc is too dirty
The CD player is in normal disk play mode
Insert the power plug firmly into the AC outlet and make sure connection is good in unit rear
Reload the disc with the label side up
Clean the disc Connect the output cables
correctly Check amplifier setup Change the installation location
Clean the disc Hold down the Program button
for 3 seconds then program the tracks
Hum Loose cable connections Firmly connect all audio plugs
©1999 Numark Industries - 14 - http://www.numark.com
TECHNICAL SPECIFICATIONS
CD MIX-1
CD Players
Quantization 16-bit linear/channel,
3 beam laser Oversampling rate 8 times Short access time (Play next track) less than 1.7sec Long access time (Track 1 ->Track 20) less than 3sec Start Time less than 0.3 sec Pitch control range +/-12% Pitch bend +/-16%
OVERALL
INPUT LEVEL/IMPEDANCE
LINE -11dBV (280mV)/47K OHM PHONO -50dBV (3mV)/47K OHM MIC -62dBV (0.8mV)/3K OHM
OUTPUT LEVEL/IMPEDANCE
ITEM 0dBV OUTPUT NON-CLIP MAX REC OUT (RCA) -15.5dBV (170mV) /1K OHM 5V MASTER OUT (RCA) 0dBV (1V) /1K OHM +14dBV (5V) MASTER OUT (XLR) 3.7dBm (1.2V) /470 OHM +14dBV (5V) PHONES (32 OHM) -18dBV(0.13V) /33 OHM 1V (30mW)
NOTE: 0dBV=1Vrms, 0dBm=0.775Vrms.
FREQUENCY RESPONSE
CD 20 - 20KHz +1,-2dB
LINE 20 - 20KHz +1,-1.5dB
PHONO 20 - 20KHz +2,-2.5dB/RIAA
MIC 33 - 15KHz +1,/-3dB
SN RATIO: (IEC-A WEIGHTED)
CD/LINE MORE THAN 85dB
PHONO MORE THAN 75dB
MIC MORE THAN 70dB
TOTAL HARMONIC DISTORTION
CD/LINE LESS THAN 0.05%( 20KHz LPF) PHONO LESS THAN 0.12% MIC LESS THAN 0.12% PHONES (32 0HM) LESS THAN 0.25%
CROSSTALK
CD MORE THAN 60 dB AT 1KHz LINE/PHONO MORE THAN 55 dB AT 1KHz
EQUALIZER
LOW +/- 12 dB (100Hz)
MID +/- 12 dB (1KHz)
HI +/- 11.5 dB (10KHz)
GENERAL:
Power Requirements DC 12V, 2.5A Dimensions 17 1/2”(W) x 10”(D) x 6 3/16”(H)
445mm(W) x 255mm(D) x 157mm(H)
Weight 11.5lbs. 5.2Kgs
- The Leader in DJ Technology
©1999 Numark Industries - 15 - http://www.numark.com
®
Professional Disc Jockey Products
LIMITED PRODUCT WARRANTY
1. What is covered and for how long? NUMARK INDUSTRIES LCC ("NUMARK") warrants to the original purchaser that NUMARK'S DJ mixers and amplifiers are free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase from an authorized NUMARK dealer and continuing for the following period of time after that date for (2) Years. The warranty is extended to (3) Years with the completion of the warranty card provided that the warranty card is completed and returned within (30) days from the date of purchase. All other NUMARK products are warranted for (1) Year including but not limited to CD players, CD Mix Stations, turntables, preamplifiers, beatkeepers, equalizers, microphones, headphones, and all other accessories.
2. What is not covered? This Limited Warranty is conditioned upon proper use of the product by the purchaser.
3. This Limited Warranty does not cover: (a) defects or damage resulting from accident, misuse, abuse, neglect, unusual physical or electrical stress, modification of any part of the product, or cosmetic damage; (b) equipment that has the serial number removed or made illegible; (c) all plastic surfaces and other externally exposed parts that are scratched or damaged due to normal use; (d) defects or damage from improper testing, operation, maintenance, installation, adjustment, or service of the mixers; (e) crossfaders.
4. What are NUMARK'S obligations? During the applicable warranty period, NUMARK will repair or replace, at NUMARK'S sole discretion, without charge to the purchaser, any defective component part of the mixer. To obtain service under this Limited Warranty, purchaser must first contact NUMARK and obtain a return authorization number ("RA#"). Purchaser must then return the mixer to NUMARK in an adequate container for shipping, accompanied by purchaser's sales receipt or comparable proof of sale showing the date of purchase, the serial number of the product, and the seller's name and address. To obtain an RA# and assistance on where to return the mixer, contact NUMARK customer service at 401-295 9000. Upon receipt, NUMARK will repair or replace the defective products. NUMARK may, at NUMARK'S sole discretion, use rebuilt, reconditioned, or new parts or components when repairing any product or replace a product with a rebuilt, reconditioned or new product. Repaired mixers will be warranted for a period equal to the remainder of the original Limited Warranty on the original mixer or for (90) days, whichever is longer. All replaced parts, components, boards and equipment become the property of NUMARK. If NUMARK determines that any mixer is not covered by this Limited Warranty, purchaser must pay all parts, shipping, and labor charges for the repair or return of such mixer.
5. What are the limits on NUMARK'S liabilities? THE WARRANTIES GIVEN IN THIS LIMITED WARRANTY, TOGETHER WITH ANY IMPLIED WARRANTIES COVERING NUMARK MIXERS, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, NUMARK SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF PROFITS, DAMAGES TO PURCHASER'S PROPERTY, OR INJURY TO PURCHASER OR OTHERS ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE ANY NUMARK MIXER, BREACH OF WARRANTY, OR NEGLIGENCE, INCLUDING BUT NOT LIMITED TO NUMARK'S OWN NEGLIGENCE, EVEN IF NUMARK OR ITS AGENT HAS BEEN ADVISED OF SUCH DAMAGES, OR FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY ANY OTHER PARTY. THIS LIMITED WARRANTY IS THE COMPLETE WARRANTY FOR NUMARK'S MIXERS, AND IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES PURCHASER'S EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS.
6. This Limited Warranty allocates risk of product failure between purchaser and NUMARK, and NUMARK'S product pricing reflects this allocation of risk and the limitations of liability contained in this Limited Warranty. The agents, employees, distributors, and dealers of NUMARK are not authorized to make modifications to this Limited Warranty, or make additional warranties binding on NUMARK. Accordingly, additional statements such as dealer advertising or presentation, whether oral or written, do not constitute warranties by NUMARK and should not be relied upon.
7. How does state law apply to this warranty? SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER.
8. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary from one jurisdiction to another.
RETURN INFORMATION
a) A Return Authorization number must be obtained from Numark through the address or phone numbers below. b) A copy of the original sales receipt must also be included for the equipment to be repaired under warranty. c) The faulty equipment must be packed in its original packaging. d) One additional outer layer of packaging must be included to ensure product safety. Failure to do so may inadequately protect the equipment in transit
and, therefore, jeopardize the customer’s warranty. e) Numark will not accept COD shipments and no call tags will be issued for merchandise return. f) Numark will not return repaired merchandise to customers by priority service, unless by written request at the customer’s cost. Requests must be
submitted in writing with merchandise returned. g) The defective Numark equipment should be sent, FREIGHT PREPAID with Return Authorization number clearly printed on the outer packaging and
original sales receipt enclosed to:
INDUSTRIES Attention: Service Department 11 Helmsman Avenue North Kingstown, RI 02852 USA
Phone: +1 (401) 295-9000 Fax:: +1 (401) 295-5200 Web: www.numark.com
Loading...