Numark Industries 9-Aug User Manual

AXIS 8/9

INHALT DER VERPACKUN

PROFESSIONAL CD PLAYER

Quick Start Owner’s Manual

BOX CONTENTS

• CD Player

• Power Cable

• Audio Cable

Manual Rápido Del Comienzo (ESPANOL)

CONTENIDO DE LA CAJA

• Lector De CD

• Cable De La Corriente Alterna

• Cable Audio

Kurzanleitung (DEUTSCH)

• CD PLAYER

• Stromanschlusskabel

• Audiokabel

Manuel d’utilisation du propriétaire

(FRANÇAIS)

Contenu de la boîte

• Lecteur de CD

• Cable d’alimentation

• Cable audio

Manuale rapido di utilizzazione (ITALIANO)

CONTENUTO DELLA SCATOLA

• CD Player

• Cavo Di Alimentazione

• Cavo Audio

RELAY CABLE

LINE OUT

CD PLAYER

MIXER

LINE

LINE OUT

CD PLAYER

CD PLAYER QUICK SETUP (ENGLISH)

1. Make sure all items listed on the front of this guide were in the box.

2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT.

3. Study this setup diagram.

4. Place mixer in an appropriate position for operation.

5. Make sure all devices are turned off and all faders and gain knobs are set to “zero”

6. Connect all stereo input sources as indicated in the diagram, your microphone, and headphones

7. Connect the stereo outputs to power amplifier(s), tape decks, and/or other audio sources.

POWER SUPPLY

8. Plug all devices into AC power.

9. Switch everything on in the following order.

• audio input sources (i.e. turntables or

CD players)

• mixer

• last, any amplifiers or output devices

10. When turning off, always reverse this operation by,

• turning off amplifiers

• mixer

• last, any input devices

11. Go to http://www.numark.com for product

registration.

More information about this product may be

found at http://www.numark.com

FEATURES:

1. PLAY/STUTTER- To start the music from the initial cue point.

2. PAUSE- To pause the music.

3. CUE- To move the music to the cue point and preview the selection.

4. JOG WHEEL-

a. INNER WHEEL- Used for various

functions such as cueing, scratching, pitch bend, searching, and effect control

b. OUTER PITCH WHEEL (AXIS 9) - Used

for temporary pitch bend.

5. LCD DISPLAY- Indicates all the functions, as they are occurring, with the CD.

6. OPEN/CLOSE- Pressing will open or close the disc tray on the transport.

7. SGL- To set play mode in single or continuous play.

8. TIME- Controls display indication of time mode.

9. PROGRAM- Used for setting track order and various specia l commands.

10. TRACK SELECT/SEARCH- a. Rotation – selects tracks b. Pressing while rotating – selects

tracks +10

c. Pressing once- Puts wheel in search

11. PITCH- Actives and sets pitch slider range.

mode.

12. KEY- Used for various key control.

13. -,+ - Works as pitch bend and controls key and pitch functions.

14. PITCH SLIDER- Controls the overall speed of the music.

15. PITCH RANGE LED- Indicates current pitch range of the pitch slider

16. EFFECT BUTTON- Used to determine desired effect.

17. EFFECT HOLD- Used to set effects to an alternate position

18. LOOP IN- Used to set stutter and loop in points.

19. LOOP OUT - Used to set loop out points and release the loop.

28 29 30 26 27

25. Power Switch- Turn on and turn off the machine with this button. The unit should always be shut down with this button first before any external power is removed. Typically it is recommended that the CD player is powered on before amplifiers and off after amplifiers to avoid an audio spike to be sent through your equipment.

26. IEC Power Plug Connector - Plug your supplied power cord in here.

27. Voltage Selector - Set this switch to the voltage for your location.

28. RCA Audio Connectors - Connect your CD player to your mixer from this line level output.

29. Relay Connector- If you wish to use the relay function plug in your 3.5mm stereo control cables into here and then into your other unit. The cable must be a stereo style plug for the units to work properly

20. RELOOP/STUTTER- Used for repeated play (stutter) from the loop in point, repeating a previously set, and hot start.

21. RELAY- Used for setting Alternating play start between attached units.

22. BEAT SYNC with MARCHING BAR GRAPHTracks the beats and measure position of music

23. CD Illumination Light (unit front) – lights up the CD drawer and CD when open.

24. CD Drawer (Unit Front) – Place your CDs you wis h to play in here. This unit is designed to play commercially available CD and properly burned and finalized CDR. Due to variances on the specification of certain CD burners and CDs some discs home made CDs may not play properly.

30. Remote Start Connector – Use this connector to plug into your fader-start compatible mixer or remote switch. This function is always active.

a. To use fader-start, connect a 1/8” mono

minijack cable to a fader-start compatible mixer. Every time you move the crossfader on the mixer over to the side that the unit is on, it will automatically start playing. When you move the fader away from that side, the unit will stop. Moving the fader back to the unit side will start play again.

b. Foot switches can also be attached to this

jac k for creative mixing techniques and can be found in most music shops. Connector plugs are often ¼” and an adapter to 1/8” will be needed for connection. There are also two types of footswitches that will work with this connector. The first is a typical, on/off pushbutton switch and are generally used for switching channels on guitar amps. The second switch is a momentary footswitch and is usually used for keyboard sustain pedals.

Cable de Relay

Lector de CD

Mezclador

Línea Adentro

Lector de CD

Línea Hacia fuera

MANUAL DE COMIENZO RÁPIDO DEL LECTOR DE CD (ESPANOL)

1. Cerciórese de que todos los items enumerados a principios de esta guía estén en la caja.

2. LEA EL LIBRETE DE LA INSTRUCCIÓN

DE SEGURIDAD ANTES DE USAR EL PRODUCTO.

3. Estudie este diagrama de ensamblaje.

4. Coloque el mezclador en una posición de funcionamiento apropiada.

5. Cerciórese de que todos los dispositivos estén apagados y todos los atenuadores y las perillas del aumento estén puestas a "cero".

6. Conecte todas las fuentes estéreas de la entrada de información según lo indicado en el diagrama, su micrófono, y auriculares

7. Conecte las salidas estéreas con el amplificador(es) del poder, las cubiertas de cinta, y/o otras fuentes audio.

Línea Hacia fuera

Fuente de Alimentaci ón

8. Tape todos los dispositivos en la corriente alterna.

9. Cambie todo encendido en la siguiente orden.

• fuentes audio de la entrada de

información (es decir placas giratorias o lectores de cd)

• el mezclador

• último, cualquier amplificador o

10. Al apagar, invierta siempre esta operación:

11. Vaya a http://www.numark.com para

enregistrar el producto.

dispositivo de salida

• apaga los amplificadores

• el mezclador

• último, cualquier dispositivo de

entrada de información

Más información sobre este producto se

puede encontrar en

http://www.numark.com

CARACTERÍSTICAS:

1. PLAY/STUTTER- Para comenzar la música de la señal inicial señale.

2. PAUSE- Para detenerse brevemente la música.

3. CUE- Para mover la música hasta un cierto punto y vea la selección de antemano.

4. JOG WHEELa. INNER WHEEL- Utilizado para varias

funciones tales como contar(cueing), rasguño (scratching), pitch bend, buscar, y control del efecto

b. OUTER PITCH WHEEL (AXIS 9)-

Utilizado para la pitch bend temporal.

5. LCD DISPLAY- Indica todas las funciones, mientras está ocurriendo, con el CD.

6. OPEN/CLOSE- Al presionar se abrirá o cerrará la bandeja que transporta el disco.

7. SGL- Para fijar el modo de operación en solo o continuo.

8. TIME- Indicación de la visualización de los controles del modo de tiempo.

9. PROGRAM- Utilizado para fijar el ordenes de la pista y varias comandos especiales.

10. TRACK SELECT/SEARCH- a. Rotación - selecciona las pistas b. Al presionar mientras que rota -

selecciona las pistas +10

c. Al presionar una vez rueda puesta

11. PITCH- Activa y establece las limitaciones

adentro empezará la búsqueda.

del resbalador Pitch.

+ 8 hidden pages