TURBO TANK
Commercial Grade
Portable HVACR Rinsing Sprayer
Nu-Calgon Part No. 4778-0
• High Velocity Portable HVAC Coil Sprayer
• Extremely Portable – NO MORE SEARCHING for a Water Connection
• Optimal 130PSI Water Pressure – Rinse Quickly and Safely
• Use with Water Only for Rinsing – Do Not Use with Chemicals
• High Capacity Lead Acid Rechargeable Battery
• Improved Brass Hardware for Commercial Grade Durability
• Perfect for Mini-Splits, Air Handlers, Condensers, and Rooftop Units
CONTENTS
OPERATING INSTRUCTIONS…………..……………………....3
IMPORTANT SAFETY INSTRUCTIONS…………..…………..3
WARNING TO REDUCE THE RISK OF INJURY..……4
LIMITED WARRANTY…………..………………………………...5
HOW TO OPERATE…………..…………………………………..8
AUTOMATIC SHUTOFF…………..……………………………...9
GENERAL MAINTENANCE…………..………………………..10
STORING OF THE PORTABLE HVAC SPRAYER…………..11
FAQ’s…………..………………………………………………..12
CONGRATULATIONS!
Thank you for your purchase of Nu-Calgon’s Turbo Tank Commercial Grade Portable HVACR
Rinsing Sprayer. We have designed this product to make your daily HVACR maintenance work
easier and quicker. No more searching for hard to access water connection or lugging around long
water hoses. Designed to be used to rinse a small air cooled coil after a Nu-Calgon cleaner has
been applied independently. We are very proud of this product and we hope that you are equally
satisfied with the quality and performance.
Thank you for your support in choosing Nu-Calgon products!
OPERATING INSTRUCTIONS
Please read these instructions and warnings carefully before using your Turbo Tank HVACR Rinsing
Sprayer.
WARNING:
Small parts may cause choking hazard.
IMPORTANT SAFETY INSTRUCTIONS
When using the Turbo Tank HVACR Rinsing Sprayer, these basic precautions should always be
followed:
1. DO NOT FILL THE TURBO TANK HVACR RINSING SPRAYER WITH ANY NU-CALGON COIL
CLEANER OR OTHER LIQUID OTHER THAN CLEAN WATER. SERIOUS INJURY MAY OCCUR.
ALSO CLEANERS CAN DAMAGE THE SPRAYER AND WILL VOID WARRANTY.
2. ALWAYS APPLY NU-CALGON COIL CLEANER SEPARATELY WITH AN AEROSOL CANISTER
OR APPLY DILUTED CLEANER WITH ANOTHER SPRAYER. THE TURBO TANK HVACR RINSING
SPRAYER IS MEANT TO BE A RINSING TOOL WITH CLEAN WATER.
3. STUDY THE PRODUCT THOROUGHLY BEFORE OPERATING IT. BE FAMILIAR WITH ITS
OPERATING CONTROLS.
4. DO NOT OPERATE THE PRODUCT UNDER THE INFLUENCE OF ALCHOHOL OR DRUGS.
5. DAMAGED HIGH PRESSURE HOSES CAN BURST AND CAN CAUSE A POTENTIALLY
HAZARDOUS SITUATION AND OR INJURY. HIGH PRESSURE HOSES SHOULD NOT
BE KINKED, CRUSHED, TWISTED, OR DAMAGED IN ANY WAY. SHOULD THIS OCCUR,
REPLACE THE HIGH PRESSURE HOSE.
6. ONLY USE WATER BETWEEN 10°C to 40°C (40°F to 104°F).
WARNING
TO REDUCE THE RISK OF INJURY:
1. Do not leave the Turbo Tank HVACR Rinsing Sprayer when plugged in. Unplug from power port
when not in use and before maintenance of the machine.
2. This is NOT a toy. Close attention is necessary when used near children.
3. Use only Nu-Calgon’s recommended accessories and replacement parts. Do not use with a
damaged cord or plug. Do not use the Turbo Tank HVACR Rinsing Sprayer if it is damaged,
dropped into water, or when it is not working as it should.
4. Do not pull the cord, carry the unit by the cord, use the cord as handle, or pull the cord around
sharp edges. Keep the cord away from heated surfaces.
5. Keep the nozzles free of obstructing objects. Do not use the Turbo Tank HVACR Rinsing Sprayer
when the nozzle clogged; keep free of dust, lint, hair, and anything that may reduce flow.
6. Keep hair, loose clothing, fingers, and all body parts away from moving machine parts.
7. Do not use without the water filter in place.
8. Turn off all controls before unplugging.
9. Using improper voltage may result in damage to the motor and possible injury to the user. The
proper voltage is listed on the cleaner plate.
10. Do not direct the water jet toward the unit itself, electrical parts, or towards other electrical
equipment.
11. Do not alter the original diameter of the spray head nozzle.
12. DISCHARGE residual pressure before disconnecting the Turbo Tank HVACR Rinsing Sprayer
hose.
13. Before using the Turbo Tank HVACR Rinsing Sprayer, CHECK that the screws are fully tightened
and that there are no broken or worn parts.
14. DO NOT USE with any chlorine based type cleaners, detergents or any coil cleaner.
15. Do not fill the water container with anything but clean water or your warranty will be VOID.
16. Never submerse the machine in water.
17. Do not allow the system to freeze. Always empty and store indoors. Freezing will damage the
pump and water lines.
18. Do not remove cover plate or attempt to disassemble your machine. This will void all warranty
and may cause serious injury.
19. ONLY use the SUPPLIED charger for your machine. Any other device may cause damage to
your machine.
20. Do not spray water directly at the eyes or mouth.
21. Only use Nu-Calgon supplied 115VAC to 12VDC convertor (p/n: 4778-12) if purchased as an
accessory. This commercial grade convertor is rated at 10Ah. The sprayer requires a minimum
6Ah rated convertor.
LIMITED WARRANTY
Nu-Calgon will warrant the product for a period of 12 months from the date of purchase to be free of
defects in material or workmanship. Keep your original sales invoice to validate the warranty period.
If the product should become defective within the warranty period, we will repair or replace any
defective parts free of charge. Return the sprayer to a Nu-Calgon authorized wholesaler to
initiate the process of repairing or replacing the defective part. Typically the sprayer can be
remedied in the field – do not send back to Nu-Calgon without prior authorization.
The warranty does not include the rechargeable battery, usual wear and tear, damage resulting
from accident or unreasonable use of the product, unauthorized repairs or parts that does not
belong to the product. The sprayer is designed for clean water only. The use of any coil cleaner will
void warranty since it will damage the wetted parts of the sprayer.
FEATURES
20
1. Water tank
2. Vented Cap (4778-15)
3. Adjustable Shoulder Strap
4. Hose Connector
5. Power Switch
6. Inlet for charger
7. Mesh Storage Compartment
8. Wheels
9. 12VDC Vehicle Adapter
10. Cover for power cord
22
21
13. Water inlet
14. Charger (4778-22)
15. Commercial Spray gun (4778-21)
16. Self-Recoil Hose (4778-20)
17. Red Straight Nozzle (4778-13)
18. Yellow 15 degree Nozzle (4778-14)
19. Indicator (Turns from RED TO GREEN
when battery is fully charged )
20. Mini-Split 90º spray w
and (4778-10)
21. 39 inch 90º spray wand - available
separately (4778-11)
11. Cover for Battery
12. Water outlet
22. 115VAC to 12VDC Converter available separately (4778-12)
Note: Sprayer uses a standard Expert Power EXP 1245, 12VDC 4.5Ah rechargeable battery.
Contact Nu-Calgon with questions, but could be purchased through Nu-Calgon p/n: 4778-25.
HOW TO ASSEMBLE
ALTERNATE: MINI-SPLIT WAND
Connect spray nozzle by pulling
back on the quick connector and
fully inserting the nozzle and
fully releasing the quick coupling
Connect spray wand by pulling
back on the quick connector and
fully inserting mini-split wand (for
cleaning the blower) and fully
releasing the quick coupling.
HOW TO REPLACE THE BATTERY*
Sprayer uses a standard Expert Power EXP1245, 12VDC 4.5Ah rechargeable lead/acid battery.
*
Battery could be purchased through Nu-Calgon p/n: 4778-25 or readily available in the market.
HOW TO OPERATE
IMPORTANT WHEN USING THE 12VDC VEHICLE ADAPTER: DISCONNECT THE POWER
CABLE WHENEVER THE VEHICLE ENGINE IS TURNED OFF FOR EXTENDED PERIODS OF
TIME. THE POWER DOES NOT TURN OFF AFTER SWITCHING OFF THE ENGINE IN CERTAIN
VEHICLES. IF THE POWER PLUG IS LEFT CONNECTED, THE VEHICLE’S BATTERY MAY
BECOME RUN DOWN OR DAMAGED.
FOR 12VDC VEHICLE ADAPTER
(Diagram 1)
Plug into vehicle power port.
Switch the power on “II” to use the
power of the car battery
NOTE: Some vehicles require that the
ignition be in the accessory position
With normal use, air can get trapped in the hose. We recommend the following steps to purge
the air out of your system and get the maximum amount of pressure out of your new Turbo Tank
HVACR Rinsing Sprayer
PURGE AIR FROM SYSTEM: To purge air, turn the unit on “II” or “I”(Diagram2). Point nozzle into
water tank and squeeze lever until steady stream of water exits the hose.
FOLLOW THESE STEPS AFTER EACH TIME YOU REFILL YOUR TANK:
1. Fill the tank with water and cap tank.
2. For 12VDC Vehicle Adapter Use: Connect to vehicle’s 12VDC power port. Turn unit on “II”.
For Battery: Charge battery and switch unit on to “I”.
For Optional Convertor: Plug into 115VAC power source and plug 12VDC vehicle adapter on
sprayer. Turn unit on “
3. Turn the power on and run for approximately 30 seconds or until a steady stream of water is
present.
4. Connect the mini-split wand or optional 39” wand to spray gun.
II”
Switch the power on “I” to use the
NOTE: Charge 6 to 8 hours before
using the sprayer for the first time
FOR BATTERY
(Diagram 2)
power of the battery
NOTE: Please start the engine while using the device if you are not sure whether the capacity of
the vehicles battery is sufficient.
AUTOMATIC SHUTOFF
THE AUTOMATIC SHUTOFF FEATURE:
When the trigger is released, the dynamic pressure sensor shuts the motor off automatically. When
the trigger is pressed, the pressure drop automatically activates the motor and pressure is increased
once again with a slight delay. To ensure the correct automatic shutoff operation, the time interval
between trigger release and engagement must not be less than 5-10 seconds.
SHUTTING DO
1. Place the switch in the OFF position.
2. Pull trigger on spray gun to relieve any water pressure in hose or spray gun.
WN YOUR PORTABLE HVAC SPRAYER:
GENERAL MAINTENANCE
FOR DEVICE:
WARNING: ALWAYS DISCONNECT THE PLUG FROM THE POWER SUPPLY BEFORE ANY
MAINTENANCE IS STARTED.
1. WATER FILTER: Inspect the water filter screen before filling with water. Clean the water filter
screen when necessary.
2. NOZZLE CLOGGED: A clogged nozzle will cause the operating pressure to be too high,
causing the portable sprayer to surge. If this happens turn unit off and unplug the pressure
sprayer:
Unplug power supply, pull trigger on spray nozzle handle to reliev
from handle.
• Flush wand assembly backwards with water or compressed air.
• If pressure is still too high, repeat steps 1-2.
3. LUBRICATION: No lubrication is required for this pump. Silicone grease may be added to
hose connector O-rings if connecting becomes difficult.
4. Add some silicone grease to the metal part of the spray nozzle if it has not been used for a
long period of time.
e pressure, remove nozzle
REPLACING FUSES:
The Turbo Tank Sprayer is equipped with two
fuses. One fuse is located in the 12VDC vehicle
adapter (See right). A fuse is also located
in the battery compartment (Fuse F10AL250V).
Check both if the sprayer d
oes not power on.
Unplug charger from wall. Unscrew
end of 12VDC vehicle adapter to
remove old fuse. Discard and
replace with new F8AL250V fuse.
FOR BATTERY:
1. Try to maintain a fully charged battery so the sprayer is ready for use. We recommend
charging the battery f
use, charge for 3-4 hours.
2. Please note that the battery’s charge will reduce over time if stored without use. Ideally charge
the battery at least once every three months to ensure it remains in a fully charged state.
3. Check the battery clamps regularly to ensure they are not loose, corroded, or defective.
4. Please always store the battery/Sprayer/Power Pack away from high temperatures, flammable
or explosive goods.
ully after each use to ensure the maximum battery life. Before the first
5. To prevent e
maintenance.
6. Please contact your local Nu-Calgon distributor or Nu-Calgon if there is any defect of the
battery. Do not disassemble the battery yourself.
7. Do not clean the battery by using solvents, as it may damage the battery.
lectrical shock, please use an insulated tool or glove when fixing or performing
STORING OF THE PORTABLE HVAC SPRAYER
Your Turbo Tank HVACR Rinsing Sprayer should be stored in such a way to protect it from freezing.
Do not store this unit outdoors or in areas where temperatures will fall below 0°C (32°F). This can
cause extensive damage to this unit and void the warranty. Before storing, follow these shut down
instructions:
DRAIN WATER FROM MACHINE:
1. Turn off the switch, squeeze the lever to release pre
handle lever to drain the water. Empty the water from the tank. Turn the unit on and run it for
approximately 30 seconds without the nozzle while engaging the handle lever.
2. Lower one end of the hose, engage the lever on the handle and allow the water to drain from
the hose.
3. Remove and place the spray gun and power cord in the mesh storage compartments.
4. If the unit must be stored under freezing condition, or will be stored for more
pump winterizer/protector or a non-toxic RV anti-freeze can be used to prevent freezing and
reduce mineral deposits.
ADD ANTI-FREEZE AS FOLLOWS:
1. Pour approximately 3/4 gallon (3 liters) of RV anti-freeze into tank.
2. Connect high pressure hose, nozzle, and power cord.
3. Turn unit on, squeeze lever until a steady stream of RV anti-freeze in present.
4. Turn unit off. Squeeze handle lever to release pressure.
ssure. Remove the nozzle and squeeze
the 30 days, a
5. Remove and place the spray gun and power cord in the mesh storage compa
USING PRESSURE SPRAYER AFTER STORING WITH ANTI-FREEZE:
1. Drain RV anti-freeze. (follow steps 1 and 2 from Drain Water from Machine)
2. Run 1 tank of fresh water through system before using and ensure that all anti-freeze is purged
from the system.
WARNING: USE ONLY RV ANTIFREEZE. OTHER FORMULATED ANTI-FREEZE PRODUCTS FOR
HVAC APPLICATIONS CAN DAMAGE PUMP AND VOID WARRANTY.
rtment.
FAQ
PORTABLE HVAC SPRAYER DOESN’T WORK?
• Check if the power cord is attached properly.
• If using the 12VDC adapter, check the Vehicle’s battery and the 12VDC vehicle adapter socket.
• Check the fuse in the 12VDC vehicle adapter.
• Check the fuse in the battery compartment.
NO WATER SPRAYS OUT WHEN STARTING THE WATER PUMP?
• Check if the nozzle is clogged.
• Check if the water inlet or outlet is clogged.
• Check if the water inlet filter screen on the base unit is clogged.
• Check if the water hose is bent.
•
NOTICE:
To avoid using up the
adapter for more than 30 minutes.
vehicle’s charge, please start the engine if you need to use the 12VDC vehicle
Specification:
• Pressure (PSI): 43.5 to 130.5
• Volts: 12V(DC)
• Power: 60W
• Hose: 236 inches (6 meters)
• Power Cord: 118 inches (3 meters)
• Capability: 4.5 gallons (17 liters)
• G.W.: 17.2 lbs. (7.8kg)
• Dimension: 14 x 9 x 21 inches (355 x 230 x530mm)
IMPORTANT: Consult Nu-Calgon literature for other details. Contact Nu-Calgon for any warranty
related concern. In most
cases, the Turbo Tank can easily be repaired in the field.
2611 Schuetz Rd. • St. Louis, MO. 63043 • 800-554-5499 • www.nucalgon.com
Calgon is a licensed trade name • (119) 3-448
Loading...