NTI VOPEX-C5V, VOPEX-M12V-4, VOPEX-C5SVA, VOPEX-C5HDTV, VOPEX-C5VA Installation And Operation Manual

...

Download

Page 1

NTI

NETWORK

TECHNOLOGIES INCORPORATED

1275 Danner Dr Aurora, OH 44202

www.networktechinc.com

Tel:330-562-7070 Fax:330-562-1999

VOPEX®Series

VOPEX-C5VA/C5V-x(C)

VOPEX-C5SVA/C5SV-x

VOPEX-C5HDTV/C5HDA-x

VOPEX-M12V-4

Video/Audio or Video Only

Splitter/Extender

Installation and Operation Manual

(Receiver not included)

MAN071 Rev Date 3/21/2012

Page 2

TRADEMARK

VOPEX is a registered trademark of Network Technologies Inc in the U.S. and other countries.

Copyright © 2003, 2012 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.

CHANGES

The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the right to make changes in the product design without reservation and without notification to its users.

WARNING: Never connect a VOPEX Series VOPEX-C5VA / -C5V / -C5SVA / -C5SV / -C5HDTV / or -C5HDA -x

Extender/Splitter to an Ethernet card, Ethernet router, hub or switch or other Ethernet RJ45 connector of an Ethernet device. Damage to devices connected to the Ethernet may result.

Note: CAT5 connection cable used between NTI XTENDEX Series Local and Remote or any XTENDEX Series products should not be run underground, outdoors or between buildings.

WARNING: Outdoor or underground runs of CAT5 cable could be dangerous and will void the warranty.

Page 3

TABLE OF CONTENTS

Introduction......................................................................................................................................................................1

Materials..........................................................................................................................................................................2

Features and Functions...................................................................................................................................................3

Limitations .......................................................................................................................................................................5

Preparation for Installation ..............................................................................................................................................5

VOPEX Installation..........................................................................................................................................................6

VOPEX-C5VA-x and VOPEX-C5V-x...........................................................................................................................6

VOPEX-C5SVA-x and VOPEX-C5SV-x......................................................................................................................8

VOPEX-C5HDTV-x....................................................................................................................................................10

VOPEX-C5HDA-x......................................................................................................................................................12

Receiver Installation......................................................................................................................................................14

ST-C5VA-R-600 and ST-C5V-R-600 Receiver .........................................................................................................14

ST-C5SVA-R-600 and ST-C5SV-R-600 Receiver ....................................................................................................15

ST-C5HDTV-R-600 and ST-C5HDA-600 Receiver..................................................................................................16

Connect the CAT5 cable............................................................................................................................................16

Plug-in and Boot Up......................................................................................................................................................17

Installation for VOPEX-M12V-4 and ST-M12V-4..........................................................................................................18

Video Quality Adjustment..............................................................................................................................................19

VOPEX-C5VA-x / -C5SVA-x / -C5HDTV-x / -C5HDA-x ............................................................................................19

VOPEX-C5V-x / -C5SV-x...........................................................................................................................................19

Technical Specifications................................................................................................................................................20

Interconnection Cable Wiring Method...........................................................................................................................22

RJ45 Connector Wiring..............................................................................................................................................22

M12 Connector Wiring...............................................................................................................................................22

Troubleshooting.............................................................................................................................................................23

Warranty Information.....................................................................................................................................................24

TABLE OF FIGURES

Figure 1- Connecting a VOPEX-C5VA-8 to a CPU............................................................................................................................6

Figure 2- Connect Local User components and CAT5 cable to VOPEX-C5VA-8..............................................................................7

Figure 3- Connecting a VOPEX-C5SVA-8 to a CPU .........................................................................................................................8

Figure 4- Connect Local User components and CAT5 cable to VOPEX-C5SVA-8............................................................................9

Figure 5- Connect HD Video and Stereo Audio sources..................................................................................................................10

Figure 6- Connect local HDTV and stereo speakers........................................................................................................................11

Figure 7- Connect HD Video and Digital Audio sources ..................................................................................................................12

Figure 8- Connect HDTV and Digital Audio devices ........................................................................................................................13

Figure 9- Connect the Extended Components to the ST-C5VA-R-600 Receiver.............................................................................14

Figure 10- Connect the Extended Components to the ST-C5SVA-R-600 Receiver ........................................................................15

Figure 11- Connect the Extended Components to the Receiver......................................................................................................16

Figure 12- Connect the CAT5 cable to the Receiver .......................................................................................................................16

Figure 13- Connect an AC adapter to a ST-C5VA-R-600 Receiver.................................................................................................17

Figure 14- Connections for VOPEX with M12 Connectors...............................................................................................................18

Figure 15- M12 Connector Wiring Pinout.........................................................................................................................................18

Figure 16- Video Adjust button for manual video quality adjustment ...............................................................................................19

Figure 17- Video quality adjustment buttons on ST-C5V-600 Receiver...........................................................................................19

Figure 18- View looking into RJ45 female........................................................................................................................................22

Page 4

NTI EXTENDEX SERIES SPLITTER/EXTENDER

INTRODUCTION

The VOPEX® Series Cat5 Video/Audio Splitter/Extender (VOPEX) is designed to enable one Video/Audio source to be viewed and heard in 4, 8, or 16 different remote locations. Remote video and audio devices can be located as much as 600 feet away from the source via Category 5 unshielded twisted-pair cable. The VOPEX-C5VA-x also allows a local video and audio device to be located near the source.

Models:

VOPEX-C5VA-x(C) Video/Audio Splitter/Extender for VGA video and line level analog audio VOPEX-C5V-x(C) Video-Only Splitter/Extender for VGA video (No Audio Support) VOPEX-C5SVA-x S-Video/Audio Splitter/Extender for S-Video and line level analog audio VOPEX-C5SV-x S-Video-Only Splitter/Extender for S-Video (No Audio Support) VOPEX-C5HDTV-x HD Video/Stereo Audio Splitter/Extender for high definition video and stereo audio VOPEX-C5HDA-x HD Video/Digital Audio Splitter/Extender for high definition video and digital audio VOPEX-M12V-4 4-Port Video Extender for VGA video with M12 connectors (No Audio Support)

x= 4,8, or 16 for the number of Receivers that can be connected.

Note: If the audio support is not present, please disregard all audio references.

The VOPEX-C5VA VGA Audio/Video Splitter/Extender via CAT5 will broadcast up-to-the-minute information to multiple remote monitors in real time. This high-resolution VGA video splitter (video port expander) is the ideal solution for any application requiring the flexibility to share information with several locations. Optional audio functionality using self-powered stereo speakers enhances your presentation.

The VOPEX C5HDTV/HDA Audio/Video Splitter/Extender via CAT5 is ideal for systems where high resolution YPbPr component video signals along with analog or digital audio signals must be transmitted long distances to multiple displays and speakers.

Possible digital video and audio sources include a DVD player , cable television box, home entertainment system, etc.. Digital audio devices include a HDTV, Home Theater System, Digital Audio Receiver, or Digital Speaker set, etc.. Some stereo line-level audio source and devices include HDTV Speak ers, Home Theater or Stereo System, Stereo Amplifier, Headphones, and Computer Speakers.

The VOPEX Series Video/Audio Splitter/Extender is extremely simple to install and has been thoroughly tested to insure reliable performance. Through the use of Category 5 unshielded twisted-pair cable it is possible to economically increase the flexibility of a computer/home entertainment system. Here are some of the features and ways this can benefit the user:

• Allows the placement of monitors/HDTVs and self-powered stereo speakers/amplifiers in different remote

locations where only these parts are needed.

• Provides an additional local access port allowing the A/V source to viewed and heard lo cally.

• Compatible with

• XGA, VGA, and SVGA systems (VOPEX-C5VA / -C5V models only)

• all video sources supporting s-video (VOPEX-C5SVA / -C5SV models only)

• High and Standard Definition YPbPr component video, S-Video, or composite video

(VOPEX-C5HDTV / -C5HDA models only)

• Provides crisp and clear resolution up to 1024x768 (VOPEX-C5VA / -C5V models only) or 800 x 600

(VOPEX-C5SVA / -C5SV models only) @ 60Hz at 600 ft.

• ST-C5HDTV / -C5HDA models support 480i (interlaced), 480p (progressive), 720i, 720p, 1080i, and 1080p formats.

• Video quality adjustment is automatic for varying lengths of CAT5 cable (models with audio support only)

• 'Video Adjustment' button allows video quality to be re-adjusted without powering down the system.

(Button is on VOPEX-C5VA / -C5SVA only- video quality adjustment is performed at Receiver for VOPEX-C5V / -C5SV.)

• Digital transmission of audio signals reduces any loss in quality.

• Compatible with all NTI A/V switches and splitters, enabling the joining of products to create a

system that satisfies all networking needs.

Page 5

NTI EXTENDEX SERIES SPLITTER/EXTENDER

MATERIALS

Materials Included with this kit:

¾ VOPEX-C5VA-x / -C5V-x / -C5SVA-x / -C5SV-x / -C5HDTV-x / -C5HDA-x /-M12V-4 (one of these) ¾ 120VAC or 240VAC at 50 or 60Hz-9VDC/1.5A AC Adapter (not included with M12)

-Or-

¾ 120VAC or 240VAC at 50 or 60Hz-5VDC/3A AC Adapter (VOPEX-C5V(A)-4C/8C models only) ¾ Line cord, country specific (not included ¾ CD with a pdf file of this manual and pdf file of a Quick Installation Guide ¾ Quick Installation Guide

Additional materials Included:

For Model Video Cable Stereo plug Cable

VOPEX-C5VA-x(C) VEXT-3 SA-3-MM VOPEX-C5V-x(C) VEXT-3 Not applicable VOPEX-C5SVA-x SVEXT-3-MM SA-3-MM VOPEX-C5SV-x SVEXT-3-MM Not applicable VOPEX-C5HDTV-x CMPSAEXT-1.5-MM (see image to right) VOPEX-M12V-4 VEXT-3 Not applicable

Legend:

• x= 4, 8, or 16 for number of ports

• MM- indicates male-male connectors

• VEXT-3- 15HD male-female video cable for connecting the VOPEX to the video source

• SA-3-MM 3.5mm stereo plug -stereo plug cable for connecting the VOPEX to the audio source

• SVEXT-3-MM 4-pin miniDIN male-male s-video cable- for connecting the VOPEX-C5SVA / -C5SV-x to the video source

• CMPSAEXT-1.5-MM 5-in-1 coax cable (3-75 ohm component video and 2-RCA stereo)-for connecting VOPEX-

C5HDTV-x to the audio and video source

Additional materials not supplied but are required:

¾ CAT5 unshielded twisted-pair cable(s) terminated with RJ45 connectors wired straight thru- pin 1 to pin 1, etc. (see pg.

14 for proper EIA/TIA 568B wiring method)

¾ One or more of the following XTENDEX receivers:

Receiver For use with

ST-C5VA-R-600 VOPEX-C5VA-x(C) ST-C5V-R-600 VOPEX-C5V-x(C) ST-C5SVA-R-600 VOPEX-C5SVA-x ST-C5SV-R-600 VOPEX-C5SV-x ST-C5HDTV-R-600 VOPEX-C5HDTV-x ST-C5HDA-R-600 VOPEX-C5HDA-x ST-M12V-R-600 VOPEX-M12V-4

Contact your nearest NTI distributor or NTI directly for all of your KVM needs at 800-RGB-TECH (800-742-8324) in US & Canada or 330-562-7070 (Worldwide) or at our website at www.networktechinc.com assistance.

¾ Cables for connecting the HD video and stereo/digital audio devices to the VOPEX-C5HDTV and VOPEX-C5HDA :

DESCRIPTION PURPOSE 75 ohm RCA cable with green, blue, red connectors Coax cable for digital audio Connect audio device to VOPEX (VOPEX-

Stereo audio cable Connect stereo audio device to VOPEX

with M12)

Connect HDTV to VOPEX

C5HDA only)

(VOPEX-C5HDTV only)

Stereo Audio connectors

CMPSAEXT-1.5-MM

(Viewed wit h th e cable laid flat)

and we will be happy to be of

Component Video connectors

Page 6

NTI EXTENDEX SERIES SPLITTER/EXTENDER

FEATURES AND FUNCTIONS

9VDC

1.5A

1a. Video -15HD male connector - for connecting the cable from the video source 1b. S-Vin - 4-pin miniDIN female connector - for connecting the cable from the video source 1c. INPUT - RCA connectors - for connecting component video (Y, Pb, Pr) and stereo audio source (R,L) 1d. INPUT -RCA connectors - for connecting component video (Y, Pb, Pr) and digital audio source (Digital) 2a. Monitor -15HD female connector - for connecting the local user's monitor 2b. S-Vout - 4-pin miniDIN female S-Video Connector - for connecting the local user's S-video compatible monitor 2c. LOCAL OUTPUT - RCA connectors - for connecting local component video (Y, Pb, Pr) and stereo audio device (R,L) 2d. LOCAL OUTPUT - RCA Connectors - for connecting local component video (Y, Pb, Pr) and digital audio device (Digital)

NTI

Network Technologies Inc

INPUT LOCAL OUTPUT

L Y Pb Pr

87654321

XTENDEX VA

Video Adjust

(Front View) (Rear View)

Cat5

VOPEX-C5HDTV-8

(Rear View)

3. Line In - 3.5mm female stereo audio connector- for connecting the cable from the audio source (VOPEX-C5VA/-C5SVA

models only)

4. Line Out - 3.5mm female stereo audio connector- for connecting the local self-powered stereo speakers (VOPEX-

C5VA/-C5SVA only)

5. Cat 5 - RJ45 female- for connecting CAT5 cables from XTENDEX Receivers

6. 9VDC 1.5A- connection jack for the 9VDC 1.5A AC adapter

7. Power - Green LED- illuminates when power has been supplied to the VOPEX

8. Video Adjust - forces the VOPEX to re-adjust the video on all channels (models with audio support only)

9. Power switch- to turn unit ON and OFF

YPbPr

NTI

1275 Danner Dr Aurora, OH 44202

Power

VOPEX-C5VA-8

NETWORK TECHNOLOGIES INCORPORATED

Tel:330- 562-70 70 Fax:33 0-562-19 99

www.nti1.com

NETWORK

Tel:330-56 2-7070

1275 Danner Dr

Fax:330-562- 1999

Aurora, OH 44202

TECHNOL OGIES

NTI

9VDC

1.5A

www.nti1.com

INCORPOR ATED

87654 3 2 1

Cat5

INPUT

Y Pb Pr Y Pb PrDigital Digital

9VDC

1.5A

87654321

Cat5

VOPEX-C5HDA-8

(Rear View)

1a2a5

VideoMonitor

Line

Out

(S-Video connecto rs on VOPEX-C5SVA-8 )

LOCAL OUTPUT

NETWORK TECHNOLOGIES INCORPORATED

NTI

Tel:33 0-562-70 70

1275 Danner Dr

Fax:33 0-562-19 99

Aurora, OH 44202

www.nti1.com

S-Vout

1b2b

S-Vin

Page 7

NTI EXTENDEX SERIES SPLITTER/EXTENDER

10a. 15HD female VGA video connector - for connecting the remote user's monitor 10b. 4-pin miniDIN female S-Video connector - for connecting the remote user's S-video compatible monitor 10c. RCA Video Connectors - connection for remote component video (Y,Pb,Pr) cable

11. Cat 5- RJ45 female - for connecting CAT5 cable from the VOPEX

12. Traffic LED- communication indic ator- illuminates when there is valid communication between the VOPEX and the

XTENDEX Receiver. (illuminates only in models with audio support)

13. Power LED- illuminates when power has been supplied to the unit 14a. Audio Connector- 3.5mm female stereo audio connector- for connecting remote self-powered speakers 14b. Stereo Audio Connectors-RCA- connection for right and left channel stereo audio amplifier 14c. Digital Audio Connector-RCA- connection for digital audio device

15. 9VDC 1.0A- conn ection jack for 9VDC 1A AC adapter

14b

14c

(Front View) (Rear View)

10c

(Front View) (Rea r View)

10c

(Front View) (Rea r View)

14a

NTI

Networ k Tec hnologi es In c

XTENDEX

Network Tech nologies Inc

XTENDEX

Network Tech nologies Inc

XTENDEX

NTI

10a

XTENDEX

Network Technologies Inc

NTI

10b

(S-video Connect or of ST-C5SVA-R-600)

1213

ST-C5VA-R-600 Receiver (Receiver not included)

XTENDEX

Network Tech nologies Inc

NTI

1312

ST-C5HDTV-600 Receiver (Receiver not included)

XTENDEX

Network Tech nologies Inc

NTI

1312

ST-C5HDA-600 Receiver (Receiver not included)

Page 8

NTI EXTENDEX SERIES SPLITTER/EXTENDER

LIMITATIONS

• The audio input of the VOPEX-C5VA is compatible with the following standard CPU audio outputs:

• Line out - typically lime green in color

• Speaker out- typically orange in color

• Headphone out- typically located on the CD-ROM

• The audio outputs of the VOPEX and the XTENDEX Receiver are compatible with self-powered stereo speakers.

PREPARATION FOR INSTALLATION

• Locations should be chosen for the monitors and speakers that also have space to connect the VOPEX and XTENDEX

Receivers within the distance provided by the cables. If extension cables are needed, contact NTI for the cables required.

• The CAT5 cables must be run to the locations where the VOPEX and XTENDEX Receivers will be connected. Be

careful to route the cables away from any sources of magnetic fields or electrical interference that might reduce the quality of the video signal (i.e. AC motors, welding equipment, etc.). NOTE: If CAT5 cable is already installed in the wall and there are RJ45 wall outlets, it will be necessary to obtain male-to-male straight through connection cables long enough to reach from the wall outlets to the connection locations of the VOPEX and XTENDEX Receivers.

• A properly grounded, polarized, and preferably surge-protected 120V or 240V electrical outlet (de pending on the AC

adapter being used) must be installed close enough to the connection location of the VOPEX and XTENDEX Receivers, monitors, stereo speakers, and CPU to plug them into.

• All cables should be installed in such a way that they do not cause stress on their connections to the equipment.

Extended lengths of cable hanging from a connection may interfere with the quality of that connection. Secure cables as needed to minimize this.

• Properly shut down and disconnect the power from all devices to be separated. If other equipment is involved whose

connections are being interrupted, be sure to refer to the instruction manuals for that equipment for proper disconnection and re-connection procedures before proceeding.

Note: CAT5 connection cable used between NTI XTENDEX Series Local and Remote or any XTENDEX Series products should not be run underground, outdoors or between buildings.

WARNING: Outdoor or underground runs of CAT5 cable could be dangerous and will void the warranty.

Page 9

NTI EXTENDEX SERIES SPLITTER/EXTENDER

VOPEX INSTALLATION

VOPEX-C5VA-x and VOPEX-C5V-x

Note: VOPEX-C5V-x Video Only Splitter/Extender does not have audio support. If the audio support is not present, please disregard all audio references.

1. Make connections between the VOPEX-C5V A-x and the audio and video source(s). (See Fig. 1.) a) Connect the male15HD cable end of a VEXT-3 to the VGA connector on the back of the

video source.

b) Connect the female 15HD cable end of the VEXT-3 cable to the 15HD male

connector marked "Video" on the VOPEX-C5VA-x.

c) Connect one 3.5mm stereo plug end of the SA-3-MM cable into the 3.5mm female audio

connector marked "line out", "spkr", or "headphones" on the audio source.

Notes: If all 3 connectors are available, use the connector marked "line out".

The "line out" connector is typically lime green and may be marked with this symbol

The "spkr" connector is typically orange, and may be marked with this symbol

The "headphones" connector may be marked with this symbol

d) Connect the other 3.5mm stereo plug end of the SA-3-MM cable into the 3.5mm female stereo

audio connector marked "Line In" on the VOPEX-C5VA-x.

VIDEO

CONN ECTOR

15HD Female Video Connector

AUDIO CONNECTOR

ONE WILL BE MARKED "line

out" ,"spkr", "head p hon e s"

OR WITH THIS SYMBOL

line out

CPU

15HD Male Video Connector

VEXT-3 (supplied)

SA-3-MM (supplied)

3.5mm Stereo Plug

VIDEO

CONNECTOR

15HD Male Video Connector

1275 Danner Dr

NETWORK

Aurora, O H 44 202

TECHNOLOG IES INCORPORATED

www.nti1.com

NTI

9VDC

1.5A

Tel:330-5 62-7070 Fax:330-5 62-1999

VOPEX-C5VA-8 (Rear View)

Cat5

4321

Line

Out

15HD Female Video Connector

VideoMonitor

Line

3.5mm Female Stereo Audio Connector

Figure 1- Connecting a VOPEX-C5VA-8 to a CPU

Page 10

NTI EXTENDEX SERIES SPLITTER/EXTENDER

2. Connect the local user to the VOPEX-C5VA-x (see Fig. 2) a) Connect the cable from the local user's VGA monitor to the 15HD female connector

marked "Monitor" on the VOPEX-C5VA-x.

b) Connect the cable from the local speakers into the 3.5mm stereo audio connector marked "Line

Out" on the VOPEX-C5VA-x.

VIDEO

CONNECTOR

15HD Female Video Connector

CAT5 Cable to ST-C5VA-R-600 Receiver

9VDC

1.5A

NTI

NETWORK TECHNOLOGIES INCORPORATED

1275 Dann er Dr Aurora, OH 44202

www.nti1.com

VOPEX-C5VA-8 (Rear View)

Tel:330- 562-70 70 Fax:33 0-562-199 9

Cat5

4321

Local User's Monitor and Speakers

Monitor

Line

Out

Multi-Scan

Video

VGA

Monitor

3.5mm Female Stereo Audio Connector

Figure 2- Connect Local User components and CAT5 cable to VOPEX-C5VA-8

3. Connect a CAT5 cable to any one of the “Cat5x” ports on the VOPEX-C5VA-x. (See Fig. 2) When

properly inserted the cable end should snap into place.

4. Repeat step 3 for each ST-C5VA-R-600 Receiver to be connected to the VOPEX-C5VA-x.

Note: If an RJ45 wall outlet is being used, connect the other end of the extension cable to the

RJ45 wall outlet.

WARNING: Never connect the VOPEX-C5VA-x Extender/Splitter to an Ethernet card, Ethernet router,

hub or switch or other Ethernet RJ45 connector of an Ethernet device. Damage to devices connected to the Ethernet may result.

Page 11

NTI EXTENDEX SERIES SPLITTER/EXTENDER

VOPEX-C5SVA-x and VOPEX-C5SV-x

Note: VOPEX-C5SV-x S-Video Only Splitter/Extender does not have audio support. If the audio support is not present, please disregard all audio references.

1. Make connections between the VOPEX-C5SVA-x and the audio and video source(s). (See Fig. 3) a) Connect a 4-pin miniDIN cable end of a SVEXT-3-MM to the VGA connector on the back of the

video source.

b) Connect the other 4-pin miniDIN cable end of the SVEXT-3-MM cable to the 4-pin miniDIN

female connector marked "S-Vin" on the VOPEX-C5SVA-x.

c) Connect one 3.5mm stereo plug end of the SA-3-MM cable into the 3.5mm female audio

connector marked "line out", "spkr", or "headphones" on the audio source.

Notes: If all 3 connectors are available, use the connector marked "line out".

The "line out" connector is typically lime green and may be marked with this symbol

The "spkr" connector is typically orange, and may be marked with this symbol

The "headphones" connector may be marked with this symbol

d) Connect the other 3.5mm stereo plug end of the SA-3-MM cable into the 3.5mm female stereo

audio connector marked "Line In" on the VOPEX-C5SVA-x.

VIDEO

CONNE CT O R

4-pin miniDIN Female S-Video Connector

AUDIO CONNECTOR

ONE WILL BE MARKED "line

out" ,"spkr", "headphones"

OR WITH THIS SYMBOL

line out

CPU

4 pin miniDIN Male S-Video Connector

SVEXT-3-MM (supplied)

SA-3-MM (supplied)

3.5mm Stereo Plug

VIDEO

CONNECTOR

4-pin miniDIN Female S-Video Connect or

1275 Dann er Dr

NETWORK TECHNOLOGIES

Aurora, OH 44202

www.nti1.com

NTI

INCORPORATED

9VDC

1.5A

VOPEX-C5SVA-8 (Rear View)

Tel:330-562-7070 Fax:330-5 62-1999

Cat5

4321

4 pin miniDIN Male S-Video Connector

S-VinS-Vout

Line

Out

3.5mm Female Stereo Audio Connector

Figure 3- Connecting a VOPEX-C5SVA-8 to a CPU

Page 12

NTI EXTENDEX SERIES SPLITTER/EXTENDER

2. Connect the local user to the VOPEX-C5SVA-x (see Fig. 4) a. Connect one end of another SVEXT-xx-MM cable to the 4-pin miniDIN female connector

marked "S-Vout" on the VOPEX-C5SVA-x. b. Connect the other end of the SVEXT-xx-MM cable to the 4-pin miniDIN female connector on the

local s-video display. c. Connect the cable from the local speakers into the 3.5mm stereo audio connector marked "Line

Out" on the VOPEX-C5SVA-x.

CAT5 Cable to ST-C5SVA-R-600 Receiver

VIDEO

CONNECTOR

4-pin miniDIN Female S-Video Connector

VOPEX-C5SVA-8 (Rear View)

NETWORK

Tel:330- 562-70 70

1275 Dann er Dr

TECHNOLOGIES

Fax:33 0-562-199 9

Aurora, OH 44202

NTI

9VDC

1.5A

www.nti1.com

INCORPORATED

87654321

S-VinS-Vout

Cat5

Line

Out

3.5mm Female Stereo Audio Connector

SVEXT-xx-MM

S-Video

Display

Local User's Display and Speakers

Figure 4- Connect Local User components and CAT5 cable to VOPEX-C5SVA-8

3. Connect a CAT5 cable to any one of the “Cat5x” ports on the VOPEX-C5SVA-x. (See Fig. 4) When properly

inserted the cable end should snap into place.

4. Repeat step 3 for each ST-C5SVA-R-600 Re ceiver to be connected to the VOPEX-C5SVA-x.

Note: If an RJ45 wall outlet is being used, connect the other end of the extension cable to the

RJ45 wall outlet.

WARNING: Never connect the VOPEX-C5SVA-x Extender/Splitter to an Ethernet card, Ethernet router,

hub or switch or other Ethernet RJ45 connector of an Ethernet device. Damage to devices connected to the Ethernet may result.

Page 13

NTI EXTENDEX SERIES SPLITTER/EXTENDER

VOPEX-C5HDTV-x

1. Make connections between the VOPEX-C5H DTV-x and the stereo audio and HD video source. (See Fig. 5.)

a) Connect the video ends of the CMPSAEXT-1.5-MM RCA coax cable (supplied) to the HD video

source.

b) Connect the video ends on the other end of the CMPSAEXT-1.5-MM RCA coax cable to connectors marked "INPUT" on the VOPEX-C5HDTV-x. Connect the RCA cables to their proper matching colors- green to "Y", blue to "Pb", and red to "Pr".

c) Connect the stereo audio end s of the CMPSAEXT-1.5-MM cable between the audio source and the "R" (right channel) and "L" (left channel) connectors on the VOPEX.

Note: The jacket of the red RCA coax (on the CMPSAEXT-1.5MM) for connection to the "R" (right channel) stereo connection is pink.

The jacket of the red RCA coax for connection to the "Pr" video connector is red

L Y Pb Pr

9VDC

1.5A

87654321

note: pink jacket

CMPSAEXT-1.5-MM

VOPEX-C5H DTV-8 (Rear View)

INPUT LOCAL OUTPUT

(supplied)

To Stereo Audio Source

Cat5

YPbPr

To HD Video Source

NTI

1275 Danner Dr Aurora, OH 4420 2

www.nti1.com

note: red jacket

NETWORK TECHNOLOGIES INCORPORATED

Tel:33 0-562- 7070 Fax:33 0-562- 1999

Figure 5- Connect HD Video and Stereo Audio sources

2. Connect the local user to the VOPEX-C5HDTV-x (see Fig. 6) a) Connect one end a set of 75 ohm RCA cables to an HDTV. b) Connect the other end of the RCA coax cables to connectors marked "LOCAL OUTPUT" on the

VOPEX-C5HDTV-x. Connect the RCA cables their proper matching colors- green to "Y", blue to "Pb", and red to "Pr".

c) Connect a stereo audio cabl e between a stereo audio device and the "R" (right channel) and "L"

(left channel) connectors on the VOPEX under "LOCAL OUTPUT".

Page 14

NTI EXTENDEX SERIES SPLITTER/EXTENDER

CAT5 Cable to ST-C5HDTV-R-600 Receiver

9VDC

1.5A

stereo audio cable

Self-Powered Amplifier

INPUT LOCAL OUTPUT

L Y Pb Pr

87654 3 21

Stereo

Speakers

Locally connected devices

VOPEX-C5HDTV-8 (Rear View)

Cat5

75 ohm RCA cables

HDTV

YPbPr

NETWORK TECHNOLOGIES INCORPORATED

NTI

Tel:33 0-562- 7070

1275 Danner Dr

Fax:33 0-56 2-1999

Aurora, OH 44202

www.nti1.com

Figure 6- Connect local HDTV and stereo speakers

3. Connect a CAT5 cable to any one of the “Cat5x” ports on the VOPEX-C5HDTV-x. (See Fig. 6) When properly

inserted the cable end should snap into place.

4. Repeat step 3 for each ST-C5HDTV-R-600 Receiver to be connected to the VOPEX-C5HDTV-x.

Note: If an RJ45 wall outlet is being used, connect the other end of the extension cable to the

RJ45 wall outlet.

WARNING: Never connect the VOPEX-C5HDTV-x Extender/Splitter to an Ethernet card, Ethernet router,

hub or switch or other Ethernet RJ45 connector of an Ethernet device. Damage to devices connected to the Ethernet may result.

Page 15

NTI EXTENDEX SERIES SPLITTER/EXTENDER

VOPEX-C5HDA-x

1. Make connections between the VOPEX-C5H DA-x and the digital audio and HD video source. (See Fig. 7.) a) Connect a set of 75 ohm RCA cables to the HD video source. b) Connect the other end of the RCA coax cables to connectors marked "INPUT" on the VOPEX-

C5HDA-x. Connect the RCA cables to their proper matching colors- green to "Y", blue to "Pb", and red to "Pr".

c) Connect a coax cable for digital audio between a digital audio source and the connector under

"INPUT" marked "Digital" on the VOPEX

9VDC

1.5A

87654321

coax cable for digital audio

To Digtal Audio Source

VOPEX-C5HDA-8 (Rear View)

INPUT

Y Pb Pr Y Pb PrDigital Digital

Cat5

75 ohm RCA cables

To HD Video Source

LOCAL OUTPUT

NTI

1275 Danner Dr Aurora, OH 44202

www.nti1.com

NETWORK TECHNOLOGIES INCORPORATED

Tel:33 0-562- 7070 Fax:33 0-56 2-1999

Figure 7- Connect HD Video and Digital Audio sources

2. Connect the local user to the VOPEX-C5HDA-x (see Fig. 7) a) Connect one end a set of 75 ohm RCA cables to an HDTV. b) Connect the other end of the RCA coax cables to connectors marked "LOCAL OUTPUT" on the

VOPEX-C5HDTV-x. Connect the RCA cables to their proper matching colors- green to "Y", blue to

"Pb", and red to "Pr".

c) Connect a coax cable for digital audio between a digital audio device "Digital" connector on the

VOPEX under "LOCAL OUTPUT".

Page 16

NTI EXTENDEX SERIES SPLITTER/EXTENDER

CAT5 Cable to ST-C5HDA-R-600 Receiver

coax cable for digital audio

Digital Audio Receiver

9VDC

1.5A

87654321

VOPEX-C5HDA-8 (Rear View)

INPUT

Y Pb Pr Y Pb PrDigital Digital

Cat5

75 ohm RCA cables

HDTV

LOCAL OUTPUT

NTI

1275 Danner Dr Aurora, OH 44202

www.nti1.com

NETWORK TECHNOLOGIES INCORPORATED

Tel:33 0-562- 7070 Fax:33 0-56 2-1999

Figure 8- Connect HDTV and Digital Audio devices

3. Connect a CAT5 cable to any one of the “Cat5x” ports on the VOPEX-C5HDA-x. (See Fig. 8) When properly inserted the cable end should snap into place.

4. Repeat step 3 for each ST-C5HDA-R-600 R eceiver to be connected to the VOPEX-C5HDA-x.

Note: If an RJ45 wall outlet is being used, connect the other end of the extension cable to the

RJ45 wall outlet.

WARNING: Never connect the VOPEX-C5HDA-x Extender/Splitter to an Ethernet card, Ethernet router,

hub or switch or other Ethernet RJ45 connector of an Ethernet device. Damage to devices connected to the Ethernet may result.

Page 17

NTI EXTENDEX SERIES SPLITTER/EXTENDER

RECEIVER INSTALLATION

ST-C5VA-R-600 and ST-C5V-R-600 Receiver

Note: This section is applicable to both models of Receiver except for step 3. When installing ST-C5V-R-600 Receivers (no audio support), disregard step 3.

1. Position a ST-C5VA-R-600 Receiv er such that the CAT5 cable, the monitor cable, speaker cable,

and the AC adapter power connector can each reach the Receiver comfortably.

2. Connect the remote user's monitor cab le to the female 15H D video connector on the Receiver.

3. Connect the remote user's speakers to the 3.5mm female stereo connector on the Receiver (see

Fig. 9).

ST-C5VA-R-600 Receiver (Front and Rear View)

Front View of Receiver

Rear View of Receiver

NTI

Network Tech nologies Inc

XTENDEX

CAT5 Cable to VOPEX-C5VA-x

Remote User's Monitor and Speakers

VGA

Multi-Scan

Monitor

15HD Female Video Connector

Figure 9- Connect the Extended Components to the ST-C5VA-R-600 Receiver

4. Make sure the CAT5 cable ha s been installed in accordance with the “Preparation for

Installation” instructions on page 5. Connect the CAT5 cable to the “Cat 5” port on the Receiver. (See Fig. 9) When properly inserted the CAT5 cable end should snap into place.

Note: If an RJ45 wall outlet is being used, connect the other end of the extension cable to the RJ45

wall outlet.

WARNING: Never connect the ST-C5VA-R-600 Receiver to an Ethernet card, Ethernet router, hub or

switch or other Ethernet RJ45 connector of an Ethernet device. Damage to devices connected to the Ethernet may result.

5. Repeat steps 1-4 for each ST-C5VA-R-600 Receiver to be connected to the VOPEX-C5VA-x.

Page 18

NTI EXTENDEX SERIES SPLITTER/EXTENDER

ST-C5SVA-R-600 and ST-C5SV-R-600 Receiver

Note: This section is applicable to both models of Receiver except for step 4. When installing ST-C5SV-R-600 Receivers (no audio support), disregard step 4.

1. Position a ST-C5SVA-R-600 Receiver such that the CAT5 cable, the SVEXT-xx-MM cable, speaker cable, and the AC adapter power connector can each reach the Receiver comfortably.

2. Connect one end of another SVEXT-xx-MM cable to the female 4-pin miniDIN video connector on

the Receiver.

3. Connect the other end of the SVEXT-xx-MM to the female s-video connector of the remote s-video

display.

4. Connect the remote user's speakers to the 3.5mm female stereo connector on the Receiver (see

Fig. 10).

ST-C5SVA-R-600 Receiver (Front and Rear View)

Front View of Receiver

Rear View of Receiver

NTI

Network Tech nologies Inc

XTENDEX

CAT5 Cable to VOPEX-C5SVA-x

Remote User's Display and Speakers

SVEXT-xx-MM

S-Video

Display

Figure 10- Connect the Extended Components to the ST-C5SVA-R-600 Receiver

5. Make sure the CAT5 cable has been installed in accordance with the “Preparation for

Installation” instructions on page 5. Connect the CAT5 cable to the “Cat 5” port on the Receiver. (See Fig. 10) When properly inserted the CAT5 cable end should snap into place.

Note: If an RJ45 wall outlet is being used, connect the other end of the extension cable to the RJ45

wall outlet.

6. Repeat steps 1-4 for each ST-C5SVA-R-600 Receiver to be connected to the

VOPEX-C5SVA-x.

WARNING: Never connect the ST-C5SVA-R-600 Receiver to an Ethernet card, Ethernet

router, hub or switch or other Ethernet RJ45 connector of an Ethernet device. Damage to

devices connected to the Ethernet may result.

Page 19

NTI EXTENDEX SERIES SPLITTER/EXTENDER

ST-C5HDTV-R-600 and ST-C5HDA-600 Receiver

1. Position the ST-C5HDxx-R-600 Receiver such that the CAT5 cable, the HD television cable, the speakers, and the AC adapter power connector can each reach the Receiver comfortably.

2. Connect 75 ohm RCA cables between the remote HDTV and the RCA connectors marked "Y", "Pb", and "Pr" on the

3. Connect coax cable for digital audio (ST-C5HDA-600 only) or stereo audio cable (ST-C5HDT V-600 only) between the

ST-C5HDA-600 Receiver

Digital Audio Receiver

Receiver as shown in Fig. 11.

audio connection(s) on the Receiver and the audio device. (See Fig. 11)

NTI

Network Technologies Inc

XTENDEX

ST-C5HDTV-600 Receiver

(Front View)

coax cable for digital audio

75 ohm RCA cables

HDTV

Self-Powered Amplifier

Remote Television

stereo audio cable

Stereo

Speakers

NTI

Network Tech nologies Inc

XTENDEX

(Front View)

75 ohm RCA cables

HDTV

emote Televisi on

Figure 11- Connect the Extended Components to the Receiver

Connect the CAT5 cable

Make sure the CAT5 cable has been installed in accordance with the “Preparation for Installation” instructions on page 5. Connect the CAT5 cable to the “Cat 5” port on the Remote Unit. (See Fig. 12) When properly inserted the CAT5 cable end should snap into place.

Note: If an RJ45 wall outlet is being used, connect the other end of the extension cable to the RJ45 wall outlet.

WARNING: Never connect the XTENDEX

to an Ethernet card, Ethernet router, hub or switch or other Ethernet RJ45 connector of an Ethernet device. Damage to devices connected to the Ethernet may result.

Figure 12- Connect the CAT5 cable to the Receiver

Green Power LED

Yellow Traffic LED

ST-C5HDTV-600 Receiver

(Rear View)

XTENDEX

Network Te chnolo gies Inc

NTI

CAT5 Cable to VOPEX

Page 20

NTI EXTENDEX SERIES SPLITTER/EXTENDER

PLUG-IN AND BOOT UP

1. Plug the power cord from each video device and the power supply for each audio device into a power outlet. Connect the 9VDC 1.5A AC adapter (or 5VDC 3A, see product markings) power connector to the power port on the

VOPEX.

3. Connect a 9VDC 1A AC adapter to each XTENDEX Receiver. Make sure the power connectors go into each port all

the way.

WARNING: The AC adapter for the Receivers is rated at 1A only. Be sure to plug the 9VDC 1A AC

adapter into the Receiver, NOT into the VOPEX! The 1A AC adapter, if connected to the VOPEX, is not powerful enough to supply the VOPEX for very long and will be damaged.

4. Plug each AC adapter into a power outlet. The green LED on the VOPEX and the yellow LED on the RJ45 connector of

each XTENDEX Receiver should illuminate, indicating that a proper power connection has been made to them. (See Fig. 13)

9 VDC

ADAPTER

Barrel

Rear View of ST-C5VA-R-600 Receiver

Yellow Power LED

Green Communication LED

Power Connector

9VDC @ 1A OUTPUT

(Outside barrel)

2.1 mm x 5.5 mm Female

(Inside barrel)

Figure 13- Connect an AC adapter to a ST-C5VA-R-600 Receiver

5. Turn ON the audio and video source(s), stereo speakers, and monitors. They should react as if they were

directly connected to each other.

Note: The green LED on the RJ45 connector of each XTENDEX Receiver will blink anytime data traffic is passing between the VOPEX and the XTENDEX Receivers, indicating proper CAT5 cable connection and communication. (See Fig. 13)

Page 21

NTI EXTENDEX SERIES SPLITTER/EXTENDER

INSTALLATION FOR VOPEX-M12V-4 AND ST-M12V-4

Installation of the VOPEX splitter and receivers with M12 connectors is the same as those with RJ45 connectors, except that M12 male connectors must be applied to the ends of the CAT5 cables. See the images below for the required connections and proper wiring pinout of the male M12 connector (wired to EIA/TIA 568B standard).

Figure 14- Connections for VOPEX with M12 Connectors

Figure 15- M12 Connector Wiring Method

Page 22

NTI EXTENDEX SERIES SPLITTER/EXTENDER

VIDEO QUALITY ADJUSTMENT VOPEX-C5VA-x / -C5SVA-x / -C5HDTV-x / -C5HDA-x

When powering ON the VOPEX-C5VA-x/-C5SVA-x/-C5HDTV-x/-C5HDA-x, video quality adjustment is done automati c ally to assure the image is as clear as possible. Once the VOPEX is up and running, the video quality can be re-adjusted at any time by pressing the recessed "Video Adjust" button. (See Fig. 16) Using a non-conductive pointed object, a momentary press of the button will force the system to automatically re-adjust the video quality.

Note: Video quality adjustment of the VOPEX-C5V-x or VOPEX-C5SV-x is performed manually at the Receiver. See "Video Quality Adjustment for VOPEX-C5V-x / -C5SV-x" below.

VOPEX-C5VA-x (Front View)

NTI

Network Technologies Inc

XTENDEX VA

Video Adjust

Press button inside using non-conductive (i.e. woo d or pl astic) point ed ob je c t to adjust video quality

Power

Figure 16- Video Adjust button for manual video quality adjustment

Video quality may need to be re-adjusted if any of the following situations occur:

• A CAT5 cable is replaced, for any reason

• A new XTENDEX Receiver is connected to the system

• CAT5 cable becomes disconnected from the VOPEX or any of the Receivers

Note: When the cable is longer than 300 feet some colored lines can be seen at the black-to-white transitions. This is a normal behavior and is caused by the different twisting rates of each pair of wires in the CAT5 cable.

VOPEX-C5V-x / -C5SV-x / -M12V-4

Video quality adjustment of the VOPEX-C5V-x, VOPEX-C5SV-x and VOPEX-M12V-4 is performed manually at the Receiver. It is possible that on initial startup the image on the monitor will not be as crisp as the image normally is. This is due to the

frequency characteristics of the CAT5 cable. It may be necessary to press the "+" or "-" buttons on the Receiver (see Fig.

17) until the image is crisp and clear. Press the "+" button if the image is not crisp and clear enough. Press the "-" button

if the image has been over-corrected (such that horizontal lines appe ar to trail or shadow at the edge of an open window). A momentary press of either button will make a minor change in the image. If either button is pressed and held, the changes made will be gradual and continuous. Ultimately, the image quality should improve to a satisfactory level. Once the adjustment is made, it should not be necessary to change it again as the new settings are stored in memory and become the default settings with each startup.

Figure 17- Video quality adjustment buttons on XTENDEX Receiver

Page 23

NTI EXTENDEX SERIES SPLITTER/EXTENDER

TECHNICAL SPECIFICATIONS

VOPEX-C5VA / -C5V Models

Maximum Resolution See chart next page Video Compatibility SVGA, XGA, VGA Video Connectors HD15 female for monitor connection

VOPEX-C5SVA / -C5SV Models

Maximum Resolution (refresh frequency 60Hz) Video Compatibility All s-video displays and sources Video Connectors 4-pin miniDIN female

All Above Models

Video Quality Adjustment

Video Coupling DC Video Maximum I/O Levels 1.45Vp-p Input / Output Impedance 75 Ohms Input Horizontal Frequency Range 15kHz to 130 kHz Input Vertical Frequency Range 30 Hz to 150 Hz Sync Types Supported Separate and composite TTL Level and sync on green Audio Connectors 3.5mm female stereo audio connectors Signal Type Line Level, stereo, unbalanced Audio Frequency Response 20Hz to 20Khz, + 1dB Signal-to-noise ratio 76 dBA Total Harmonic Distortion and Noise 0.017% Stereo Crosstalk -70 dB Audio Maximum I/O Levels 3.1Vp-p Output Impedance Max 2K Ohms, unbalanced THD+N 0.017%,F=20-20KHz, RL=2K Ohm, Vout=1 Vrms

VOPEX-C5HDA/-C5HDTV Models

Video Compatibility HDTV Component- Y,Pb, Pr Connectors RCA Video Maximum I/O Levels 1.45Vp-p (no offset) Input / Output Impedance 75 Ohms Maximum Resolutions 1080i and 720p @ 600ft

Stereo Audio

Signal Type Line Level, stereo, unbalanced Audio Connectors RCA Audio Frequency Response 20Hz to 20Khz, + 1dB Signal-to-Noise Ratio (SNR) 76 dBA Total Harmonic Distortion and Noise Stereo Crosstalk -70 dB Audio Maximum I/O Levels 3.1Vp-p

Output Impedance Max 2K Ohms, unbalanced Digital Audio

Signal Type S/PDIF

Connectors RCA

Input/Output Level 0.5 Vp-p

Input / Output Impedance 75 Ohms

HD15 male for CPU video connection 800 x 600 - up to 600 feet

Automatic, for up to 600 feet of CAT5 cable, with manual override (video quality adjustment can only be performed manually at the Receiver for VOPEX-C5V / -C5SV)

1080p @ 400ft

0.017%

Page 24

NTI EXTENDEX SERIES SPLITTER/EXTENDER

General (All Above Models)

Interconnect Cable CAT5/5e Solid UTP EIA/TIA 568B wiring w/ male RJ45 connectors VOPEX-C5 Power VOPEX-C5V(A)-4/8C Power Receiver Power AC Adapter Power Connector 2.1 x 5mm connector, center positive Operating Temperature Range 32°F to 100°F (0°C to 38°C) VOPEX Size (In.) WxDxH VOPEX-C5V(A)-x VOPEX-C5V(A)-4C VOPEX-C5V(A)-8C XTENDEX Receiver Size (In.) WxDxH 3.25x3.4x1

VOPEX-M12V-4

Maximum Resolution See chart below Video Compatibility SVGA, XGA, VGA Video Connectors HD15 female for monitor connection

CAT5 Connectors M12 Female VOPEX-M12V-4 Power ST-M12V-R-600 Power Operating Temperature Range -4°F to 158°F (-20°C to 70°C) VOPEX Size (In.) WxDxH 5.6x3.5x1.7 XTENDEX Receiver Size (In.) WxDxH 3.25x3.4x1 Interconnect Cable CAT5 shielded stranded EXANE cable

Distances and Resolutions for CAT5/CAT5e and CAT6 Cables (VOPEX-C5VA / -C5V ONLY)

CABLE DISTANCE (feet) RESOLUTION

CAT5/CAT5e (UTP) 600 1024x768 at 60Hz CAT5/CAT5e (UTP) 400 1280x1024 at 60Hz CAT5/CAT5e (UTP) 300 1600x1200 at 60Hz CAT5/CAT5e (UTP) 100 1920x1440 at 60Hz CAT6 (UTP) 300 1024x768 at 60Hz CAT6 (UTP) 200 1280x1024 at 60Hz CAT6 (UTP) 100 1920x1440 at 60Hz

Distances and Resolutions for CAT5 EXANE Cable (VOPEX-M12V-4 ONLY)

DISTANCE (feet) RESOLUTION

200 1280x1024 at 60Hz 100 1920x1440 at 60Hz

50 1920x1440 at 60Hz

120V or 240V at 50 or 60Hz-9VDC/1.5A via AC Adapter 120V or 240V at 50 or 60Hz-5VDC/3A via AC Adapter 120V or 240V at 50 or 60Hz-9VDC/1.0A via AC Adapter

8.5x6x2.5

5.1x3.4x1.1

5.1x3.4x1.7

HD15 male for CPU video connection 18-36VDC, 1.0A

18-36VDC, 1.0A

Page 25

NTI EXTENDEX SERIES SPLITTER/EXTENDER

INTERCONNECTION CABLE WIRING METHOD

The connection cable between the VOPEX and each XTENDEX Receiver is terminated with either RJ45 connectors or M12 connectors (see installation instruction for you model) and must be wired according to the EIA/TIA 568B industry standard. Wiring is as per the tables and drawings below.

Pair 3

RJ45 Connector Wiring

1 White/Orange 2 T 2 Orange 2 R 3 White/Green 3 T 4 Blue 1 R 5 White/Blue 1 T 6 Green 3 R 7 White/Brown 4 T 8 Brown 4 R

Pin Wire Color Pair Function

Pair 2 Pair 1

Pair 4

T 5

Figure 18- View looking into RJ45 female

Note: CAT5 connection cable used between NTI XTENDEX Series Local and Remote or any XTENDEX Series products should not be run underground, outdoors or between buildings.

WARNING: Outdoor or underground runs of CAT5 cable could be dangerous and will void the warranty.

M12 Connector Wiring

Page 26

NTI EXTENDEX SERIES SPLITTER/EXTENDER

TROUBLESHOOTING

Each and every piece of every product produced by Network Technologies Inc is 100% tested to exacting specifications. We make every effort to insure trouble-free installation and operation of our products. If problems are experienced while installing this product, please look over the troubleshooting chart below to see if perhaps we can answer any questions that arise. If the answer is not found in the chart, please check the FAQs (Frequently Asked Questions) at our website at http://www.networktechinc.com or contact us directly for help at 1-800-742-8324 (800-RGB-TECH) in US & Canada or 1330-562-7070 worldwide. We will be happy to assist in any way we can.

Problem Cause Solution

VOPEX or XTENDEX power LED does not illuminate

No video on monitor/display

The picture on the monitor is black and white, rather than color Monitor sometimes loses sync, causing it to go blank for a second or two

A constant vertical wobble appears down the screen

Video picture is not sharp or is smeared

No audio

• Power supply is not connected or plugged-in.

• One or more video cables is loose or disconnected.

• No power to the VOPEX or the XTENDEX Receiver.

• Video Cable was not attached when CPU was booted.

• CAT5 cable is not connected.

The video cable was not attached to the CPU when it was booted.

• Electrical power system is very noisy, particularly the ground.

• The CAT5 cable is not properly connected.

• CAT5 cable is too close to a strong power source.

• Monitor is too close to a power source or another monitor.

• All Video Cables are not firmly seated.

• CAT5 cable is too long.

• The CAT5 cable is not properly

connected.

• A cabling change has been made while the system was powered.

• A new receiver was connected while the system was powered

• Video was not manually adjusted

• Audio cable is not properly

plugged in

• Speakers are not plugged in

• CAT5 cable is not properly

connected

• Make sure each outlet is live and the AC adapters are plugged-in. (one for each Remote and one for the VOPEX)

• Make sure DC plugs are fully connected

• Check all video cable connections

• Make sure power LEDs are illuminated for local and

remote. If not, see solution for problem above.

• With all the cables properly connected, reboot the CPU.

• Check cable connections. Make sure they are snapped-

in properly and completely and reboot.

With the cables all properly connected, reboot the CPU.

• Make sure the interconnection cable is not near any power lines.

• Check cable connections. Make sure they are snappedin properly and completely.

• Reroute CAT5 cable if possible.

• Move the monitor

• Check all connections. Make sure all cables are fully

seated.

• Verify length is within specified limits-600'.

• Check cable connections. Make sure they are snapped-

in properly and completely.

• Press the "Video Adjust" button. (See "Video Quality" on page 18.)

• Adjust video at the receiver (See "Video Quality" on page 18.)

• Check all cable connections

• Verify speakers are powered (if applicable)

• Check CAT5 cable connections

Page 27

NTI EXTENDEX SERIES SPLITTER/EXTENDER

WARRANTY INFORMATION

The warranty period on this product (parts and labor) is two (2) years from the date of purchase. Please contact Network Technologies Inc at (800) 742-8324 (800-RGB-TECH) or (330) 562-7070 or visit our website at

http://www.networktechinc.com for information regarding repairs and/or returns. A return authorization number is required

for all repairs/returns.

Manual 071 Rev. 3/21/12