NTI SM-8X8-DVI, SM-4X4-DVI User Manual
V
EEMUX
®
Series
SM-4X4-DVI
SM-8X8-DVI
DVI Video Matrix Switch
Installation and Operation Manual
MAN114 Rev Date 10/7/2009
TRADEMARK
VEEMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries.
COPYRIGHT
Copyright © 2009 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.
CHANGES
The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the
right to make changes in the product design without reservation and without notification to its users.
i
TABLE OF CONTENTS
Introduction......................................................................................................................................................................1
Materials..........................................................................................................................................................................2
Features and Functions...................................................................................................................................................2
Connect Cables...............................................................................................................................................................4
Operating the sm-4x4-dvi................................................................................................................................................5
Learn Mode..................................................................................................................................................................5
Enter Learn Mode.....................................................................................................................................................5
Change Connections Manually....................................................................................................................................5
Operating the sm-8x8-dvi................................................................................................................................................6
Accessing the Setup Menu..........................................................................................................................................6
Change Connections via RS232 .................................................................................................................................7
Setup Control Computer...........................................................................................................................................7
RS232 Protocol.........................................................................................................................................................9
Embedded Commands.............................................................................................................................................9
Technical Specifications................................................................................................................................................11
Warranty Information.....................................................................................................................................................11
TABLE OF FIGURES
Figure 1- Connect devices and sources to VEEMUX ........................................................................................................................4
Figure 2- Configure the VEEMUX connection....................................................................................................................................7
Figure 3- Smart Control Connection Display......................................................................................................................................8
ii
NTI VEEMUX DVI VIDEO MATRIX SWITCH
INTRODUCTION
The VEEMUX® 4x4 DVI video matrix switch (VEEMUX) provides non-blocking access to four single link digital DVI video sources
from four displays. Locate computers up to 19 feet away from displays, enabling easy access to multiple servers in various
locations.
Also available:
SM-8X8-DVI- provides non-blocking access to 8 single link digital DVI video sources from 8 eight displays
Features:
• Configure and control the switch through serial port, or front panel buttons.
• Supports DVI-D interface for crisp and clear video quality on flat panel displays.
• Supports DVI operation at the maximum TMDS rate of 2 x 1.65 Gb/second
• Silent fanless operation.
• Provides high digital resolution up to 1920x1200 for monitors and 1080p for HDTV displays.
• EDID learning for the support of any DVI display device.
• Built in default EDID configuration tables for both PC and Mac.
• Each output provides one video signal.
• Each input can be independently connected to any or all outputs.
HDTV
DVD Player
Satellite
Set Top Box
DVI Projector
DVI C omputer
Typical Application
DVI M onitor
SM-4X4-DVI
1
NTI VEEMUX DVI VIDEO MATRIX SWITCH
MATERIALS
Materials supplied with this kit:
• NTI SM-4X4-DVI or SM-8X8-DVI DVI Video Matrix Switch
• 100-240VAC at 50 or 60Hz-5VDC/3.0A (4x4) or 4.0A (8x8) AC Adapter
• CD containing pdf of this manual and control software
Materials Not supplied but REQUIRED:
• DVI-IS-xx-MM cable for each monitor and CPU being connected to the switch- available in 3, 6,10, and 15 foot lengths
where:
xx is the length of the cable in feet
MM indicates male-to-male connector
FEA TURES AND FUNCTIONS
NTI
Network Tech nologies In c
R
VEEMUX
R
OUTPUT 1
OUTPUT 2 OUTPUT 3 OUTPUT 4
INPUT 1 INPUT 2 INPUT 3
56 78
1. Seven-segment Input LEDs- for indicating what inputs (video sources) are connected to the labeled output (display device)
and Learn Mode indicator
2. Power LED- for indicating that power has been supplied to the unit
3. Output LEDs- for indicating which output is being configured when “Input Select” is pressed
4. Selection buttons- for manually changing connections between the inputs and outputs
5. OUTPUTx- female DVI connector- for connecting DVI cable from display device
6. INPUTx- female DVI connector- for connecting DVI cable from video source
7. RS232 connector- 9D male- for connecting the user's RS232 control cable
8. 5VDC- power input connector for attachment of power supply
FRONT VIEW OF SM-4X4-DVI
Input
Input
123
Output
4
Select
Output
Select
12 3 4
R
NTI
1275 Dann er Dr
INPUT 4
Aurora, OH 44 202
Tel:330-562-70 70
Fax:330-562-19 99
www.network techinc.com
IR
RS232
REAR VIEW OF SM-4X4-DVI
-
5VDC
3A
+
2
Loading...