NTE NTE580 Datasheet

NTE580

General Purpose Silicon Rectifier

Fast Recovery

Features:

D High Temperature Metallurgically Bonded–No Compression Contacts
D Fast Switching for High Effeciency
D 3A Operation at TA = +25°C with No Thermal Runaway

Maximum Ratings and Electrical Characteristics:

(TA = +25°C unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%)

Maximum Recurrent Peak Reverse Voltage 600V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum RMS Voltage 420V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum DC Blocking Voltage 600V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Average Forward Rectified Current (.375” (9.5mm) Lead Length, TA = +75°C) 3A. . . . . .

Peak Forward Surge Current (8.3ms Single Half Sine–Wave Superimposed on Rted Load) 100A.

Maximum Instantaneous Forward Voltage (IF = 3A) 1.3V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum DC Reverse Current (VDC = 600V, TA = +25°C) 5µA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Average Reverse Current (PRV = 600V)

TA = +25°C 2µA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TA = +100°C 100µA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Reverse Recovery Time (Note 1) 150ns. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Typical Junction Capacitance (Note 2) 65pF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Junction Temperature Range, T
Storage Temperature Range, T

stg

Lead temperature (During Soldering, .375” (9.5mm) from case, 10sec), T

J

L

Note 1. Reverse Recovery Test Conditions: IF = 0.5A, IR = 1.0A, IRR = 0.25A.
Note 2. Measured at 1MHz and applied reverse voltage of 4V.

–65° to +175°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–65° to +175°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

+350°C. . . . . . . . . . . . . .

1.000
(25.4)

Min

.180 (4.6) Max.042 (1.07) Max

Color Band Denotes Cathode

.300 (7.6) Max