NTE NTE2013, NTE2012, NTE2011, NTE2015, NTE2014 Datasheet

NTE2011/NTE2012/NTE2013/NTE2014/NTE2015

Integrated Circuit

7–Channel Darlington Array/Driver

Description:

The NTE2011 through NTE2015 are high–voltage, high–current Darlington arrays in a 16–Lead DIP
type package and are comprised of seven silicon NPN Darlington pairs on a common monolithic sub­strate. All units have open–collector outputs and integral diodes for inductive load transient suppres­sion.

Peak inrush currents to 600mA (NTE2011, NTE2013, NTE2014) or 750mA (NTE2012, NTE2015) are
permissible, making them ideal for driving tungstun filament lamps.

The NTE201 1 is a general purpose array that may be used with standard bi–polar digital logic using
external current limiting, or with most PMOS or CMOS directly. This device is pinned with outputs
opposite inputs to facilitate printed wiring board layouts.

The NTE2012 is designed for use with 14V to 25V PMOS devices. Each input has a Zener diode and
resistor in series to limit the input current to a safe value in that application. The Zener diode also gives
this device excellent noise immunity.

The NTE2013 has a 2.7kΩ series base resistor for each Darlington pair, allowing operation directly
with TTL or CMOS operating at a supply voltage of 5V. This device will handle numerous interface
needs – particularly those beyond the capabilities of standard logic buffers.

The NTE2014 has a 10.5kΩ series input resistor that permits operation directly from CMOS or PMOS
outputs utilizing supply voltages of 6V to 15V. The required input current is below that of the NTE2013,
while the required input voltage is less than that required by the NTE2012.

The NTE2015 is designed for use with standard TTL and Schottky TTL, with which higher output cur­rents are required and loading of the logic output is not a concern. This device will sink a minimum
of 350mA when driven from a “totem pole” logic output.

Absolute Maximum Ratings: (TA = +25°C for any one Darlington pair unless otherwise specified)
Output Voltage, V
Input Voltage, V

IN

CE

50V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NTE2012, NTE2013, NTE2014 30V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NTE2015 15V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous Collector Current. I

C

NTE2011, NTE2013, NTE2014 500mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NTE2012, NTE2015 600mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous Input Current, I
Power Dissipation, P

D

IN

25mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

One Darlington Pair 1W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Total Device (Note 1) 2W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Ambient Temperature Range, T
Storage Temperature Range, T

stg

A

–20° to +85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–55° to +150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Note 1. The NTE2015 is a discontinued device and no longer available.
Note 2. Derate at the rate of 16.6mW/°C above +25°C.

Note 3. Under normal operating conditions, these devices will sustain 350mA per output with

V

CE(sat)

= 1.6V at +70°C with a pulse width of 20ms and a duty cycle of 34%.

Electrical Characteristics: (TA = +25° unless otherwise specified)

Parameter Symbol Device Test Conditions Min Typ Max Unit

Output Leakage Current I

Collector–Emitter V

CEX

CE(sat)

Saturation Voltage NTE2013

Input Current I

Input Voltage V

IN(ON)

I

IN(OFF)

IN(ON)

All VCE = 50V, TA = +25°C – – 50 µA

VCE = 50V, TA = +70°C – – 100 µA
NTE2012 VCE = 50V, TA = +70°C, VIN = 6V – – 500 µA
NTE2014 VCE = 50V, TA = +70°C, VIN = 1V – – 500 µA
NTE201 1

NTE2014

NTE2014

IC = 100mA, IB = 250µA – 0.9 1.1 V

IC = 200mA, IB = 350µA – 1.1 1.3 V

IC = 350mA, IB = 500µA – 1.3 1.6 V
NTE2012

NTE2015

IC = 200mA, IB = 350µA – 1.1 1.3 V

IC = 350mA, IB = 500µA – 1.3 1.6 V

IC = 500mA, IB = 600µA – 1.7 1.9 V
NTE2012 VIN = 17V – 0.82 1.25 mA
NTE2013 VIN = 3.85V – 0.93 1.35 mA
NTE2014 VIN = 5V – 0.35 0.50 mA

VIN = 12V – 1.0 1.45 mA
NTE2015 VIN = 3V – 1.5 2.4 mA

All IC = 500µA, TA = +70°C 50 60 – µA
NTE2012 VCE = 2V, IC = 500mA – – 17 V
NTE2013 VCE = 2V, IC = 200mA – – 2.4 V

DC Forward Current

h

Transfer Ratio
Input Capacitance C
Turn–On Delay t
Turn–Off Delay t

Clamp Diode Leakage I

Current
Clamp Diode Forward Voltage V

FE

IN
PLH
PHL

R

VCE = 2V, IC = 250mA – – 2.7 V
VCE = 2V, IC = 300mA – – 3.0 V

NTE2014 VCE = 2V, IC = 125mA – – 5.0 V

VCE = 2V, IC = 200mA – – 6.0 V
VCE = 2V, IC = 275mA – – 7.0 V

VCE = 2V, IC = 350mA – – 8.0 V
NTE2015 VCE = 2V, IC = 350mA – – 2.6 V
NTE201 1 VCE = 2V, IC = 350mA 1000 – –

All – 15 25 pF
All 0.5 Ein to 0.5 E
All 0.5 Ein to 0.5 E
All

VR = 50V, TA = +25°C – – 50 µA

out
out

– 0.25 1.0 µs
– 0.25 1.0 µs

VR = 50V, TA = +70°C – – 100 µA

F

All IF = 350mA – 1.7 2.0 V