NTE NTE1953 Datasheet

NTE1953

Integrated Circuit

Positive 3 Terminal Voltage Regulator,

Low Dropout Voltage, 10V, 1A

Description:

The NTE1953 positive voltage regulator features the ability to source 1A of output current with a drop­out voltage of typically 0.5V and a maximum of 1V over the entire temperature range. Furthermore,
a quiescent current reduction circuit has been included which reduces the ground current when the
differential between the input voltage and the output voltage exceeds approximately 3V. The quies­cent current with 1A of output current and an input–output differential of 5V is therefore only 30mA.
High quiescent currents only exist when the regulator is in the dropout mode (VIN – V

Features:

D Dropout Voltage: 0.5V (Typ) @ IO = 1A
D Output Current in Excess of 1A
D Reverse Battery Protection
D Internal Short Circuit Current Limit

OUT

≤ 3V).

Absolute Maximum Ratings: (TA = +25°C unless otherwise specified)
Input Voltage, V

I

Survival Voltage (≤100ms) 60V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operational Voltage 26V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Internal Power Dissipation (Note 1), P
maximum Junction Temperature, T
Operating Temperature Range, T
Storage Junction Temperature Range, T

D

J

A

stg

Lead Temperature (During Soldering, 10sec max), T

L

Internally Limited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

+150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–40° to +125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–65° to +150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

+230°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Note 1. Thermal resistance without a heatsink for junction–to–case temperature is 3°C/W. Thermal

resistance case–to–ambient is 50°C/W

Electrical Characteristics: (VIN = 15V, IO = 1A, C

unless otherwise specified)

Parameter Symbol Test Conditions Min Typ Max Unit

= 22µF, CO = 0.1µF, TJ = +25°C

OUT

Output Voltage V

OUT

Line Regulation Reg
Load Regulation Reg
Output Impedance Z

5mA ≤ IO ≤ 1A 9.7 10.0 10.3 V
12V ≥ VIN ≥ 26V, IO = 5 mA – 20 100 mV

line

50mA ≤ IO ≤ 1A – 65 100 mV

load

100mADC and 20mArms, fo = 120Hz – 65 – MΩ

O

Quiescent Current 12V ≥ VIN ≥ 26V, IO = 5 mA – 10 15 mA

VIN = 15V, IO = 1A – 30 45 mA
Output Noise Voltage V
Ripple Rejection RR fo = 120Hz, 1V

10Hz – 100kHz, IO = 5mA – 300 – µV

n

, II = 100mA 51 63 – dB

rms

rms

Long Term Stability S – 36 – mV/1000Hr
Dropout Voltage VIN–VOIO = 1A – 0.5 0.8 V

IO = 100mA – 110 150 mA
Short Circuit Current I

SC

1.6 1.9 – A
Maximum Line Transient VO ≤ 11V, RO = 100Ω, T ≤ 100ms 60 75 – V
Maximum Operational

26 31 – V

dc

Input Voltage

Reverse Polarity Input

RO = 100Ω –15 –30 – V

Voltage DC

Reverse Polarity Input

T ≤ 100ms, RO = 100Ω –50 –75 – V

Voltage Transient

.147

(3.75)

Dia

Max

.070 (1.78) Max

V

.100 (2.54)

.420 (10.67)

Max

.110 (2.79)

GND

.500

(12.7)

Max

.250 (6.35)

Max

.500

(12.7)

Min

IN

V

OUT

GND