NTE NTE1635 Datasheet
NTE1635
Integrated Circuit
Speaker Protector/Voltage/Temperature/Overload
Description:
The NTE1635 is a monolithic integrated circuit in an 8–Lead SIP type package designed for use in
protecting power amplifiers and speakers in various amplifier and receiver applications.
Features:
D Built–In Relay Driver
D Single Power Source
D Wide Operating Supply Range: 25V to 60V
D Plus and Minus Voltage using One Pin (Both Pin3 and Pin4 Posses the Same Functions and
Detect Plus and Minus Voltage)
D AC Voltage Detector (Pin5)
D Circuit Protection by Plus Voltage Detection is Provided by Connecting D1 Diode Externally (Pin6)
D Relay–On Lag Time Adjustable by External Applications
D Short Relay–Off Time (25ms Typ Under the Standard External Applications)
Typical Applications:
D For Speaker Protection, use Pin3 (or Pin4) to Detect Setoff of Quiescent Output DC Voltage
and to Turn the Relay Off
D For Power Amplifier Protection, use Pin3 (or Pin4) with an External Thermo–Sensitive Device
to Detect the Temperature Increase and to Turn the Relay Off
D Power Amplifier can be Protected by Detecting Overload and Turning the Relay Off with Pin6
D In case of Overload Detection by Constant–Current or by Constant–Voltage Drive using an
External Diode D1, the Latch Mechanism keeps the Relay On until the Power is Switched Off
D For Prevention of Pop Noise at Power Off use Pin5. AC Voltage Disappeance is Immediately
Detected when the Amp’s Switch has been Off. This Minimizes the Relay–Off Time and thus
can Prevent Pop Noise Generated by Mute–Off Time Lag
Absolute Maximum Ratings:
Total Power Disipation (T
Operating Temperature Range, T
Storage Temperature Range, T
Supply Voltage (Pin1), V
Supply Current (Pin1), I
CC(max)
1(max)
(TA = +25°C unless otherwise specified)
= +70°C), P
A
opr
stg
T
400mW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
–20° to +70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
–55° to +125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute Maximum Ratings (Cont’d): (TA = +25°C unless otherwise specified)
Supply Current (Pin3, Note 1), I
Supply Current (Pin4, Note 1), I
Supply Voltage (Pin5), V
Supply Current (Pin6), I
5(max)
6(max)
Supply Voltage (Pin7, Note 2), V
Supply Current (Pin7, Note 2), I
Supply Voltage (Pin8), V
Supply Current (Peak, Pin8), I
8(max)
8(max)
3(max)
4(max)
7(max)
7(max)
Less than Pin7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
±3mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
±3mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
–10V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Note 1. Pos it iv e c u rr en t d enotes input current a t P in3 a nd P in4, N egative current denotes o utput c urrent
Note 2. V
When applying current to V
= 8V is derived when driven by a constant voltage source without any resistance.
7(max)
throught a resistance VCC the maximum value of input current
7
to Pin7 should be used instead of the above values.
Electrical Characteristics:
Parameter Symbol Test Conditions Min Typ Max Unit
Threshold Voltage at Pin3,
Positive Side
Threshold Voltage at Pin3,
Negative Side
Threshold Voltage at Pin4,
Positive Side
Threshold Voltage at Pin4,
Negative Side
Threshold Voltage at Pin6 V
Threshold AC Voltage at Pin5 V
Threshold Voltage at Pin5 V
Current Drain at Pin7 I
(VCC = +45V unless otherwise specified)
+V
–V
+V
–V
th(6)
AC(on)
th(5)
Apply positive voltage to Pin3 through an ex-
th(3)
ternal resistance (56kΩ). Measure Pin3 volt-
age while Pin1 voltage changes from low (1V)
to high (45V) during the above process.
Apply negative voltage to Pin3 through an ex-
th(3)
ternal resistance (56kΩ). Measure Pin3 volt-
age while Pin1 voltage changes from low (1V)
to high (45V) during the above process.
Apply positive voltage to Pin4 through an ex-
th(4)
ternal resistance (56kΩ). Measure Pin4 volt-
age while Pin1 voltage changes from low (1V)
to high (45V) during the above process.
Apply negative voltage to Pin4 through an ex-
th(4)
ternal resistance (56kΩ). Measure Pin4 volt-
age while Pin1 voltage changes from low (1V)
to high (45V) during the above process.
Apply voltage to Pin6 through D1. Measure
voltage on Pin6 while Pin1 voltage changes
from low (1V) to high (45V) during the above
process.
Apply AC voltage to Pin5 through D2. Measure AC voltage on Pin5 while Pin1 voltage
changes from low (1V) to high (45V) during
the above process.
Apply voltage to Pin5 directly. Measure voltage on Pin5 when Pin1 voltage change from
low (1V) to High (45V) during the above process.
Measure Pin7 input current when turning
(7)
relay on.
0.89 1.20 1.61 V
–1.86 –1.20 –0.84 V
0.89 1.20 1.61 V
–1.86 –1.20 –0.84 V
0.90 1.15 1.40 V
– 2.5 – V
–1.8 –1.2 0 V
16.5 18.5 20.5 mA
rms
Loading...