NSi Industries W100 User Manual
TORK MODEL W100
SEVEN DAY CALENDAR DIAL TIME SWITCH
SWITCH: SPST
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
120VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON and OFF trippers close and
open all circuits simultaneously. Dial is graduated in one hour intervals. There must be an ON and an OFF tripper for each day of the
week operations are desired. Place tripper on dial edge as shown in
diagram. Set point of each tripper at the desired operating time.
Hold tripper securely against dial and tighten knurled screw firmly
by hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes.
DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close cir-
cuit. Press down lever on left of nameplate to open it.
Disconnect power at main panel prior to installing or servicing this time switch or
the equipment connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C
(167 degrees F)
TORK
®
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
LI-598(A)
Typical connections for 120VAC
OFF
TRIPPER
ON
TRIPPER
TIME
POINTER
W
E
D
T
U
E
N
S
E
T
M
I
D
N
I
G
H
T
M
I
D
N
I
G
H
T
M
I
D
N
I
G
H
T
N
O
O
N
O
N
A
M
P
M
A
M
P
M
A
M
P
M
OFF
ON
T
I
M
E
9
7
5
3
1
1
1
9
7
5
3
1
1
1
9
7
5
3
1
1
1
9
7
5
3
1
1
9
7
5
3
1
1
1
9
7
5
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
O
F
F
O
N
TORK
➤
MANUAL
ON
LEVER
MANUAL
OFF
LEVER
TIME
➤
H
N
L
MOTOR
MOTEUR
▲▲
1X
2
LOAD
CHARGE
CARGA
TORK MODEL W120
SEVEN DAY CALENDAR DIAL TIME SWITCH
SWITCH: SPDT
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
120VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON trippers close circuit A. OFF
trippers close circuit B. Dial is graduated in one hour intervals.
There must be an ON and an OFF tripper for each day of the week
operations are desired. Place tripper on dial edge as shown in diagram. Set point of each tripper at the desired operating time. Hold
tripper securely against dial and tighten knurled screw firmly by
hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes.
DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close cir-
cuit. Press down lever on left of nameplate to open it.
Disconnect power at main panel prior to installing or servicing this time switch or
the equipment connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C
(167 degrees F)
TORK
®
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
LI-602(A)
OFF
TRIPPER
ON
TRIPPER
TIME
POINTER
W
E
D
T
U
E
N
S
E
T
M
I
D
N
I
G
H
T
M
I
D
N
I
G
H
T
M
I
D
N
I
G
H
T
N
O
O
N
O
N
A
M
P
M
A
M
P
M
A
M
P
M
OFF
ON
T
I
M
E
9
7
5
3
1
1
1
9
7
5
3
1
1
1
9
7
5
3
1
1
1
9
7
5
3
1
1
9
7
5
3
1
1
1
9
7
5
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
O
F
F
O
N
TORK
➤
MANUAL
ON
LEVER
MANUAL
OFF
LEVER
TIME
➤
H
LOAD A
CHARGE A
CARGA A
N
MOTOR
MOTEUR
▲
▼
L 1 X 2
H
LOAD B
CHARGE B
CARGA B
N
TORK MODEL W202
SEVEN DAY CALENDAR DIAL TIME SWITCH
SWITCH: DPST
CONTACT RATINGS:
40 AMP TUNGSTEN 120VAC
40 AMP RESISTIVE
120-277VAC SINGLE PHASE
40 AMP GENERAL PURPOSE
120-277VAC SINGLE PHASE
20 AMP INDUCTIVE
120VAC, 277VAC
SINGLE PHASE
1000VA PILOT DUTY
120-277VAC
2 HP (24 FLA) 120VAC;
5HP (28 FLA) 240VAC
TIMING MOTOR :
208-277VAC 60Hz
POWER CONSUMPTION :
3 WATTS MAX.
INSTALLATION AND OPERATING INSTRUCTIONS
TO SET ON AND OFF TIMES: ON and OFF trippers close and
open all circuits simultaneously. Dial is graduated in one hour intervals. There must be an ON and an OFF tripper for each day of the
week operations are desired. Place tripper on dial edge as shown in
diagram. Set point of each tripper at the desired operating time.
Hold tripper securely against dial and tighten knurled screw firmly
by hand. (Do not use pliers).
NOTE: Trippers are inter-changeable. With the knurl screw inserted
in the side marked ON, it will become an ON tripper. If the tripper is
turned over and the screw inserted in the side marked OFF, it
becomes an OFF tripper.
Be certain to select the proper day and notice whether the selected time is AM or PM. Minimum ON
time is 1 hour. Minimum OFF time is 2 hours. (There must be at least six hours between any two
OFF trippers).
TO SET DIAL TO TIME: Turn dial COUNTER-CLOCKWISE until correct time of day and day of week
is indicated by time pointer. For ACCURATE OPERATION, care must be used in setting dial to time.
Each notch advances the dial approximately 15 minutes.
DO NOT FORCE DIAL BACKWARDS.
TO OMIT A DAY: Remove both ON and OFF trippers from the dial for the day or days to be omitted.
FOR MANUAL OPERATION OF CONTACTS: Press down lever on right of nameplate to close cir-
cuit. Press down lever on left of nameplate to open it.
Disconnect power at main panel prior to installing or servicing this time switch or
the equipment connected to it.
Connect in accordance with national and local electrical codes.
Supply Connections: Use gauge specified (AWG # 8-14) suitable for 75 degrees C
(167 degrees F)
TORK
®
1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542
FAX: 914-664-5052
LI-599(A)
OFF
TRIPPER
ON
TRIPPER
TIME
POINTER
W
E
D
T
U
E
N
S
E
T
M
I
D
N
I
G
H
T
M
I
D
N
I
G
H
T
M
I
D
N
I
G
H
T
N
O
O
N
O
N
A
M
P
M
A
M
P
M
A
M
P
M
OFF
ON
T
I
M
E
9
7
5
3
1
1
1
9
7
5
3
1
1
1
9
7
5
3
1
1
1
9
7
5
3
1
1
9
7
5
3
1
1
1
9
7
5
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
2
1
2
1
0
8
6
4
O
F
F
O
N
TORK
➤
MANUAL
ON
LEVER
MANUAL
OFF
LEVER
TIME
➤
Typical for 208-240VAC supply. Typical for 277VAC supply.
MOTOR
MOTEUR
L
H
1X
H
CHARGE
LOAD
2
H
N
CARGA
L
MOTOR
MOTEUR
1X
LOAD LOAD
CHARGE
CARGA
2
CHARGE
CARGA
Loading...