NPC SM5904CF Datasheet

NIPPON PRECISION CIRCUITS INC.

NIPPON PRECISION CIRCUITS-1

SM5904CF

compression and non compression type
shock-proof memory controller

Overview

- 2-channel processing

- Serial data input
⋅ 2s complement, 16-bit/MSB first, right-justified
format

- Wide capture function
(up to 3 × speed input rate)

- System clock input
⋅ 384fs (16.9344 MHz)

- Shock-proof memory controller

⋅ ADPCM compression method
⋅ 4-level compression mode selectable

4-bit compression mode 2.78 s/Mbit
5-bit compression mode 2.22 s/Mbit
6-bit compression mode 1.85 s/Mbit
Full-bit non compression mode 0.74 s/Mbit

⋅ External DRAM configurations usable

2 × 4M DRAM (1M × 4 bits)

Internal and External 4M DRAM

1 × 4M DRAM (1M × 4 bits)

Only Internal 4M DRAM

- Compression mode selectable

- Microcontroller interface

⋅ Serial command write and status read-out

⋅ Data residual detector:

15-bit operation, 16-bit output

⋅ Digital attenuator

8-bit setting

⋅ Soft attenuator function

Noiseless attenuation-level switching
(256- step switching in 23 ms max.)

⋅ Soft mute function

Mute ON in 23 ms max.
Direct return after soft mute release

⋅ Forced mute

- Extension I/O
Microcontroller interface for external control
using 4 extension I/O pins

- +2.5 to + 3.3 V operating voltage range

- Schmitt inputs
All input pins (including I/O pins) except CLK
(system clock)

- Reset signal noise elimination
Approximately 3.8 µs or longer (65 system
clock pulses) continuous LOW-level reset

- Digital audio interface (DIT)

- 44-pin QFP package (0.8 mm pin pitch)

The SM5904CF is a compression and non com­pression type shock-proof memory controller LSI for
compact disc players. The compression level can
be set in 4 levels, and external 4M DRAM can be

connected to expand the memory to 4M bits. Digital
attenuator, soft mute and related functions are also
incorporated. It operates from a 2.5 to 3.3 V supply
voltage range.

Features

Ordering Information

SM5904CF 44pin QFP

NIPPON PRECISION CIRCUITS-2

SM5904CF

Package dimensions

(Unit: mm)

44-pin QFP

13.20 0.30

13.20 0.30

+

10.00 0.20

+

0.10MAX

0.35

+

0.05

0.10

2.30MAX

2.05 0.10

+

0.15 0.10

+

0.15MAX

0.80 0.20

1.60

0.80

+

+

+

10.00 0.20

0.15

+

0.05

0.10

0 to 8

Pinout

(Top View)

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

VDD2

UC1
UC2
UC3
UC4

VSS2

DIT

NTEST1

CLK

VSS1

YSRDATA

NWE
D1
D0
D3
D2
NCAS2
NTEST2
YMCLK
YMDATA
YMLD
YDMUTE

YLRCK

YSCK

ZSCK

ZLRCK

ZSRDATA

YFLAG

YFCLK

YBLKCK

NRESET

ZSENSE

VDD1

A3A2A1A0A4A5A6A7A8

A9

NRAS

SM590

4CF

NIPPON PRECISION CIRCUITS-3

SM5904CF

Pin number Pin name I/O Function Setting

HL

1 VDD2 - VDD supply pin
2 UC1 Ip/O Microcontroller interface extension I/O 1
3 UC2 Ip/O Microcontroller interface extension I/O 2
4 UC3 Ip/O Microcontroller interface extension I/O 3
5 UC4 Ip/O Microcontroller interface extension I/O 4
6 VSS2 - Ground
7 DIT O Digital audio interface
8 NTEST1 Ip Test pin Test

9 CLK I 16.9344 MHz clock input
10 VSS1 - Ground
11 YSRDATA I Audio serial input data
12 YLRCK I Audio serial input LR clock Left channel Right channel
13 YSCK I Audio serial input bit clock
14 ZSCK O Audio serial output bit clock
15 ZLRCK O Audio serial output LR clock Left channel Right channel
16 ZSRDATA O Audio serial output data
17 YFLAG I Signal processor IC RAM overflow flag Overflow
18 YFCLK I Crystal-controlled frame clock
19 YBLKCK I Subcode block clock signal
20 NRESET I System reset pin Reset
21 ZSENSE O Microcontroller interface status output
22 VDD1 - VDD supply pin
23 YDMUTE I Forced mute pin Mute
24 YMLD I Microcontroller interface latch clock
25 YMDATA I Microcontroller interface serial data
26 YMCLK I Microcontroller interface shift clock
27 NTEST2 Ip Test pin Test
28 NCAS2 O DRAM2 CAS control(Use External DRAM)
29 D2 Ip/O DRAM data input/output 2
30 D3 Ip/O DRAM data input/output 3
31 D0 Ip/O DRAM data input/output 0
32 D1 Ip/O DRAM data input/output 1
33 NWE O DRAM WE control
34 NRAS O DRAM RAS control
35 A9 O DRAM address 9
36 A8 O DRAM address 8
37 A7 O DRAM address 7
38 A6 O DRAM address 6
39 A5 O DRAM address 5
40 A4 O DRAM address 4
41 A0 O DRAM address 0
42 A1 O DRAM address 1
43 A2 O DRAM address 2
44 A3 O DRAM address 3

Ip : Input pin with pull-up resistor Ip/O : Input/Output pin (With pull-up resistor when in input mode)
28, 33 to 44 pins for high-impedance output and 29 to 32 pins for input pull-up condition except for using external DRAM.

Pin description

NIPPON PRECISION CIRCUITS-4

SM5904CF

Parameter Symbol Rating Unit

Supply voltage V

DD - 0.3 to 4.6 V

Input voltage V

I VSS - 0.3 to VDD + 0.3 V

Storage temperature T

STG - 40 to 125 ˚C

Power dissipation P

D 600 mW

(VSS = 0V, VDD1, VDD2 pin voltage = VDD)

(*1) Refer to pin summary on the next page.
Note. Values also apply for supply inrush and switch-off.

Parameter Symbol Rating Unit

Supply voltage V

DD 2.5 to 3.3 V

Operating temperature T

OPR −10 to 70 ˚C

(VSS = 0V, VDD1, VDD2 pin voltage = VDD)

Parameter Pin Symbol Condition Rating Unit

Min Typ Max

Current consumption VDD I

DD (*A)SHPRF ON 9 18 mA

(*A)Through mode 2.6 5 mA

Input voltage CLK H level V

IH1 0.7VDD V

L level V

IL1 0.3VDD V

V

INAC AC coupling 1.0 VP-P

(*2,3,4) H level VIH2 0.8VDD V

L level V

IL2 0.2VDD V

(*5) H level V

IH3 0.8VDD V

L level V

IL3 0.2VDD V

Output voltage (*4,6) H level V

OH1 IOH = - 0.5 mA VDD - 0.4 V

L level V

OL1 IOL = 0.5 mA 0.4 V

(*5,7) H level V

OH2 IOH = - 0.5 mA VDD - 0.4 V

L level V

OL2 IOL = 0.5 mA 0.4 V

Input current CLK I

IH1 VIN = VDD 10 30 60 µA

I

IL1 VIN = 0V 10 30 60 µA

(*3) I

IL2 VIN = 0V 6 25 200 µA

(*4,5) I

IL3 VIN = 0V 1 3 6 µA

Input leakage current (*2,3,4,5) I

LH VIN = VDD - 10 10 µA

(*2) I

LL VIN = 0V - 10 10 µA

(*A) VDD1 = VDD2 = 3 V, CLK input frequency fXTI= 384fs = 16.9344 MHz, all outputs unloaded,
SHPRF: Shock-proof,
typical values are for V

DD1 = VDD2 = 3 V.

Electrical characteristics

Recommended operating conditions

DC characteristics

Standard voltage: (VDD1 = VDD2 = 2.5 to 3.3 V, VSS = 0 V, Ta = −10 to 70 ˚C)

Absolute maximum ratings

NIPPON PRECISION CIRCUITS-5

SM5904CF

(*1) Pin function Clock input pin (AC input)

Pin name CLK

(*2) Pin function Schmitt input pins

Pin name YSRDATA, YLRCK, YSCK, YFLAG, YFCLK, NRESET,

YBLKCK, YDMUTE, YMLD, YMDATA, YMCLK

(*3) Pin function Schmitt input pin with pull-up

Pin name NTEST1, NTEST2

(*4) Pin function I/O pins (Schmitt input with pull-up in input state)

Pin name UC1, UC2, UC3, UC4

(*5) Pin function I/O pins (Schmitt input with pull-up in input state)

Pin name D0, D1, D2, D3

(*6) Pin function Outputs

Pin name ZSCK, ZLRCK, ZSRDATA, ZSENSE

(*7) Pin function Outputs

Pin name NCAS2, NWE, NRAS, A0, A1, A2, A3, A4, A5, A6, A7, A8, A9, DIT

<Pin summary>

NIPPON PRECISION CIRCUITS-6

SM5904CF

Parameter Symbol Condition Rating Unit

System clock Min Typ Max

Clock pulsewidth (HIGH level)

tCWH 26 29.5 125 ns

Clock pulsewidth (LOW level)

tCWL 26 29.5 125 ns

Clock pulse cycle

tCY 384fs 56 59 250 ns

CWL

t

CY

t

0.5V

DD

CLK

CWH

t

Parameter Symbol Rating Unit Condition

Min Typ Max

YSCK pulsewidth (HIGH level)

tBCWH 75 ns

YSCK pulsewidth (LOW level)

tBCWL 75 ns

YSCK pulse cycle

tBCY 150 ns

YSRDATA setup time

tDS 50 ns

YSRDATA hold time

tDH 50 ns

Last YSCK rising edge to YLRCK edge

tBL 50 ns

YLRCK edge to first YSCK rising edge

tLB 50 ns

0 3fs Memory system ON

YLRCK pulse frequency (MSON=H)

See note below. fs fs Memory system OFF

(MSON=L)

Note. When the memory system is OFF (through mode), the input data rate is synchronized to the system clock input (384fs), so input

data needs to be at 1/384 of this frequency. But, this IC can tolerate a certain amount of jitter. For details, refer to Through-mode
operation.

YSCK

YSRDATA

YLRCK

BCY

t

DS

t

DH

t

BCWH

t

BCWL

t

LB

t

BL

t

0.5V

DD

0.5V

DD

0.5V

DD

Serial input (YSRDATA, YLRCK, YSCK pins)

AC characteristics

Standard voltage: VDD1 = VDD2 = 2.5 to 3.3 V, VSS = 0 V, Ta = −10 to 70 ˚C
(*) Typical values are for fs = 44.1 kHz

System clock (CLK pin)

System clock input

NIPPON PRECISION CIRCUITS-7

SM5904CF

Parameter Symbol Rating Unit

Min Typ Max

YMCLK LOW-level pulsewidth

tMCWL 30 + 2tCY ns

YMCLK HIGH-level pulsewidth

tMCWH 30 + 2tCY ns

YMDATA setup time

tMDS 30 + tCY ns

YMDATA hold time

tMDH 30 + tCY ns

YMLD LOW-level pulsewidth

tMLWL 30 + 2tCY ns

YMLD setup time

tMLS 30 + tCY ns

YMLD hold time

tMLH 30 + tCY ns

Rise time

tr 100 ns

Fall time

tf 100 ns

ZSENSE output delay

tPZS 100 + 3tCY ns

Note. tCY is the system clock cycle time (59ns typ).

YMDATA

YMCLK

ZSENSE

YMLD

YMDATA

YMCLK

YMLD

MDS

t

MDH

t

MCWL

t

MLS

t

MCWH

t

MLH

t

MLWL

t

PZS

t

0.5V

DD

0.5V

DD

0.5V

DD

0.5V

DD

0.5V

DD

0.3VDD

0.3VDD

0.7VDD

0.7VDD

f

t

r

t

Reset input (NRESET pin)

Parameter Symbol Rating Unit

Min Typ Max

First HIGH-level after supply voltage rising edge

tHNRST 0 tCY (Note)

NRESET pulsewidth

tNRST 64 tCY (Note)

Note. tCY is the system clock (CLK) input (384fs) cycle time.

tCY = 59 ns, tNRST (min) = 3.8 µs when fs = 44.1 kHz

NRESET

VDD1,VDD2

HNRST

t t

NRST

Microcontroller interface (YMCLK, YMDATA, YMLD, ZSENSE pins)

NIPPON PRECISION CIRCUITS-8

SM5904CF

Parameter Symbol Condition Rating Unit

Min Typ Max

ZSCK pulsewidth

tSCOW 15 pF load 1/96fs

ZSCK pulse cycle

tSCOY 15 pF load 1/48fs

ZSRDATA and ZLRCK output delay time

tDHL 15 pF load 0 60 ns
tDLH 15 pF load 0 60 ns

DRAM access timing (NRAS, NCAS2, NWE, A0 to A9, D0 to D3)

Parameter Symbol Condition Rating Unit

Min Typ Max

NRAS pulsewidth

tRASL 15 pF load 5 tCY(note)

tRASH 15 pF load 3 tCY

NRAS falling edge to NCAS2 falling edge tRCD 15 pF load 2 tCY

NCAS2 pulsewidth tCASH 15 pF load 5 tCY

tCASL 15 pF load 3 tCY

NRAS Setup time tRADS 15 pF load 1 tCY

falling edge to address Hold time tRADH 15 pF load 1 tCY

NCAS2 Setup time tCADS 15 pF load 1 tCY

falling edge to address Hold time tCADH 15 pF load 5 tCY

NCAS2 Setup time tCWDS 15 pF load 3 tCY

falling edge to data write Hold time tCWDH 15 pF load 3 tCY

NCAS2 Input setup tCRDS 40 ns

rising edge to data read Input hold

tCRDH 0ns

NWE pulsewidth

tWEL 15 pF load 6 tCY

NWE falling edge to NCAS2 falling edge tWCS 15 pF load 3 tCY

Refresh cycle Non compression 2.8 ms

(fs = 44.1 kHz playback)

tREF 4M 6-bit compression 7.3 ms

Memory system ON

DRAM 5-bit compression 8.8 ms

Decode sequence operation(READ=H)

× 1 or × 2 4-bit compression 10.9 ms

Note. tCY is the system clock (CLK) input (384fs) cycle time. tCY = 59 ns when fs = 44.1 kHz

ZSCK

ZSRDATA

0.5V

DD

ZLRCK

0.5V

DD

DHL

t

SCOY

t

SCOW

t

DLH

t

SCOW

t

Serial output (ZSRDATA, ZLRCK, ZSCK pins)

NIPPON PRECISION CIRCUITS-9

SM5904CF

,,,,,,,,,,,,,,

,,,,,,,,,,,,,,

,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

,,,,,,,

,,,,,,,

,,,,,,,

NCAS2

A0 to A9

D0 to D3

(WRITE)

NRAS

D0 to D3

(READ)

NWE

(WRITE)

3

WCS

t

6

WEL

t

CRDH

t

CRDS

t

CWDH

t

CWDS

t

33

5

CADH

t

CADS

t

RADH

t

RADS

t

111

5

32

t

RCD

t

CASL

CASH

t

RASH

t

3

t

CY

5

RASL

t

t

CY

tCY

tCY

tCY

tCY tCY tCY tCY

tCY tCY

tCY

tCY

DRAM access timing (with double DRAM) ∗ Use external DRAM.

The NWE terminal output is fixed HIGH during read timing.

DIT Interface (DIT pin)

tDI0H

0.5V

DD

DIT

tDI0L tDI1H tDI1L

6tCY 6tCY 3tCY 3tCY

Parameter Symbol Condition Rating Unit

Min Typ Max

0 data H level

tDI0H 15 pF load 6 tCY(Note)

0 data L level

tDI0L 15 pF load 6 tCY

1 data H level tDI1H 15 pF load 3 tCY

1 data L level tDI1L 15 pF load 3 tCY

Note. tCY is the system clock (CLK) input (384fs) cycle time. tCY = 59 ns when fs = 44.1 kHz.

NIPPON PRECISION CIRCUITS-10

SM5904CF

Control
Input 1

Control
Input 2

Micro-

controller

Interface

General

Port

Output Interface Input Interface

Attenuator Input Buffer

Decoder Encoder

4M DRAM / External DRAM Interface

YBLKCK

YFCLK

YFLAG

YMDATA

YMCLK

YMLD

ZSENSE

UC1 to UC4

YDMUTE

NRESET

NTEST1,2

CLK

NRAS

NCAS2

NWE

A0 to A9

D0 to D3

Through

Mode

Compression

Mode

ZLRCK

ZSCK

ZSRDATA

YLRCK

YSCK

YSRDATA

DIT

SM5904

Block diagram

NIPPON PRECISION CIRCUITS-11

SM5904CF

Write command format (Commands 80 to 86)

SM5904CF has two modes of operation; shock­proof mode and through mode.

The operating sequences are controlled using com­mands from a microcontroller.

D7 D6 D5 D4 D3 D2 D1 D0 B7 B6 B5 B4 B3 B2 B1 B0

COMMAND 8bit DATA 8bit

YMDATA

YMCLK

YMLD

B7 B6 B5 B4 B3 B2 B1 B0

COMMAND 8bit

YMDATA

YMCLK

YMLD

S7 S6 S5 S4 S3 S2 S1 S0

STATUS 8bit

ZSENSE

B7 B6 B5 B4 B3 B2 B1 B0

COMMAND 8bit

YMDATA

YMCLK

YMLD

S7 S6 S1 S0

RESIDUAL DATA 16bit

ZSENSE

M1 M2 M7 M8

Functional description

Read command format (Command 92 (memory residual read))

Read command format (Commands 90, 91, 93)

Microcontroller interface

Commands from the microcontroller are input using
3-wire serial interface inputs; data (YMDATA), bit
clock (YMCLK) and load signal (YMLD).

In the case of a read command from the microcon­troller, bit serial data is output (ZSENSE) synchro­nized to the bit clock input (YMCLK).

Write command format (Commands 87)

D11 D10 D4 D3 D2 D1 D0 B7 B6 B5 B4 B3 B2 B1 B0

COMMAND 8bit DATA 12bit

YMDATA

YMCLK

YMLD